One (1) 1997 POREBA TRP-93N: One (1) 1997 POREBA TRP-93N
Swing Over Guideways 36.6"
Swing Over Saddle 21.6"
Distance Between Centers 118"
Workpiece Weight, In Chuck 1,800 lbs
Workpeice Weight Between Centers 10,000 lbs
Headstock Spindle Spped Range Infinitley Variable 1 to 350 RPM
Number of Ranges 2
Spindle Nose A1-20
Front Bearing 14.75"
Spindle Bore 12.50"
Main Drive 40 HP Continuous 49 HP (50% Duty Cycle)
Cross Slide Travel X Axis 21.5"
Working Geed Range Axis X .0001-9.8
Working Feed Range Axis Z .0001-9.8
Rapid Travel Z Axis 157 IPM
Rapid Travel X Aixs 157 IPM
Feed Thrust Z Aixs 5,500 Lbs
Ball Screw X Axis 1.57"
Ball Screw Z Axis 2.5"
Carriage Length Bearing on Bedways 27.5"
Width of Cross Slideways 9.8"
Eight Position Sauter Tool Turret, Sauter 8 Pos Disk Turret Model 0.5.480.52
Tool Size ACC to VDI3425 50 MM
Max Permissible Cutting Torque at Radial Tool Overhang of 12.5": 53,000
Admissible Feed Force (Axis Z) 44,000 LBF
Swivel time for 180 deg Index 3.0 Sec
Indexing Precision (+/-) 4.0
Repetitive Precision (+/-) 1.6
Tailstock Quill Diameter (Taper) 5.11 (MT6)
Quill Travel 11.80"
Two Speed Quill Movement 1:1 & 1:5
Tailstock Set Off (+/-).6"
Width of Bed 23.00"
One (1) 2001 Mori Seiki SL-250BMC/500: One (1) 2001 Mori Seiki SL-250BMC/500
Fanuc 18
Swing Over Bed 26.8"
Swing Over Cross Slide 20.1"
Between Centers 22.6"
Max. Turning Diameter 15.3"
Max. Turning Length 19.1"
Max.Bar Capacity 2.8"
X-Travel 9.3"
Z-Travel 19.5"
Spindle Speed 3500 RPM
Spindle Nose A2-8
Through Hole 3.3"
Number Tool Stations 12
Shank Height for Square Tool 1"
Max. Boring Bar 2"
Turret Indexing Time 0.2 Seconds
Rotary Tool Speed 3000 RPM
Tailstock Travel 19.3"
Tailstock Spindle 3.3"
Tailstock SpindleTravel 4.7"
Spindle Motor Drive 25 HP
Rotary Tool Motor HP 8.7 HP
Coolant Tank Capacity 54.1 Gallons
Includes:
Fanuc 18
Chip Conveyor
2 Live Holders 1-X, 1-Z
Programmable Tailstock
Toolpresetter
All Available Tooling and Manuals
One (1) 1998 Hitachi-Seiki HT23J: One (1) 1998 Hitachi-Seiki HT23J
Max Turning Dia 13.30"
Max Turning Length 24.80"
Max Swing 17.70"
Kitagawa Hydraulic Chuck 10"
Max Bar Capacity 2.75"
HeadstockA2-8 Spindle Nose
3.000" Bore
20-4000 RPM
20 HP
Tailstock#5MT Quill Center
20.500" Body Travel Standard
Turret10 Position
Axis TravelX-8.200"
Z-24.80"
1181 IPM Traverse Rate
Equipped With:
Siecos J CNC Control
Tool Eye
Chip Conveyor
One (1) 1985 Dianichi MG-63: One (1) 1985 Dianichi MG-63
Swing Over Bed 24.822"
Swing Over Carriage 13.79"
Bed Width 18.912"
Formation of Main Spindle Edge JIS A1-11
Diameter of Front Bearing For Main Spindle 5.516"
Diameter of Main Spindle Through Hole 3.349"
Diameter of Main Spindle Tapered Hole (1/10 metric taper) No 100
Diameter of Tailstock Spindle 3.546"
Size of Center MT # 5
Width of Crossslide 11.032"
Tool Rest Type Automatic Square Tool Rest
Size to Tool 0.985" x 0.985"
Max Movable Distance of X Axis 12.608"
Max Movable Distance of Tailstock Spindle 5.91"
10" Chuck
One (1) 1999 Dianichi F-25: One (1) 1999 Dianichi F-25
Swing Over Bed 19.6"
Center Distance 24.4"
X Axis Travel 6.89"
Z Axis Travel 26.4"
Spindle Speed 35-3500 RPM
Turret 10 Station
Spindle Nose A2-8
Spindle Bore 3.1"
Bar Capacity 2.5"
Motor HP 20 HP
10" 3 JAwHydraulic Chuck
Equipped With 10" 3 Jaw Hydraulic Chuck
Chip Conveyor
14" Color CRT on Control
One (1) 1982 HES 600: One (1) 1982 HES 600
Fanuc 6T Control
40 HP Option
12 Position Turret
15" Chuck
A1-8 Spindle
New Bearing Z Axis
30 Deg Slant Bed
Auto Lube System
3 Speed Headstock Automatic
Hydraulic Tailstock # 4 Taper
Swing Over Bed 24"
Swing Over Cross Slide 12 1/2"
Distance Between Centers 122"
3" Bore
Z Axis Travel 66"
X Axis Travel 14 3/4
Rapid 320 IPM
One (1) 1987 DAEWOO Puma 6: One (1) 1987 DAEWOO Puma 6
Swing Over Bed 20"
Swing Over Carriage 12.2"
Recom Turing Dia/Length 6.5/14.6
Max Turning Dia 14.6"
Max Bar Working Dia 1.58"
Chuck Size 6.5"
Spindle Nose/Bore A2 #5/1.8
Bearing Dia front/rear 3.1/2.8
Spindle Speed 60-6000 RPM
Spindle Motor Cont/ 30 Min 11/15 HP
Quill Dia/ Stroke 2.6/4.0
Taper of Center MT # 3
Travel Distance X/Z 7.9/15.0
Electric Power Supply 30 KVA
Fanuc 6T
30 deg Slant Design
Hydraulic Tlsk
10 Station Bolt on turret
6" Kitagawa 3 Jaw Chuck
Powerful 15 HP (11 Kw) AC Spindle Motor
Fast 945 IPM (24 m/min) Rapid Traverse
Rigid One Piece Meehanite Cast Iron Bed
Hardened and Ground Box Way Construction
Precision 6000 RPM Cartridge Spindle
Non Stop Bidirectional Turret Indexing
Double end Pretensioned Ball Screw Support
State of the Art 32 Bit Fanuc Controller
One (1) 1998 CITIZEN L-20VII: One (1) 1998 CITIZEN L-20VII
Max Bar Capacity 0.812"
Main and Sub Spindle Speeds 10,000 RPM (M) 8000 (S)
Live Milling Speeds 200-5000 RPM
# of Live Tool Positions 4
# of OD 6
# of ID 6 (3 front, 3 back)
Spindle Motor (with step up ratio) 4.96 HP
Main Spindle Indexing C Axis
Sub Spindle Indexing 1 deg
Equipped With Canned Cycle for Drilling
C Axis on Main Spindle
1 Degree on Back Spindle
User Macros
Main/Back Spindle Synch
Control Mitsubishi meldus Windows Based CNC
1999 Femco HL-15: 1999 Femco HL-15
6” Chuck
23” Centers
1.77 Bar
6,000 RPM
10 HP
12 Station Turret
Chip Conveyor
Tail Stock
Fanuc OT Control.
(2) Two Machines Available
1999 Mazak Multiplex-6200 : 1999 Mazak Multiplex-6200
GL-100 Loader
Chip Conveyor
Two 8" Chucks
8 Rotary heads
Turret Air Blast Left and Right
Tool Eyese Left and Right
NAKAMURA TOME METHODS Slant SL-3B 2-axes CNC Turning Center: NAKAMURA TOME METHODS Slant SL-3B 2-axes CNC Turning Center
Max. swing over door 22.05”
Max. swing over slide cover 27.17”
Max. swing over bed 31.1”
Max. swing over cross slide 18.9”
Max. turning diameter 15.75”
Max. turning length 21.26”
Max. distance between spindle nose and turret face 30.31”
Min. distance between spindle nose and turret face 7.48”
Hole through Spindle 3.15”
Spindle nose A1-8
Hole through draw tube 2.56”
Round collet capacity 2.50”
Spindle speed range 10 to 3500 RPM
X-axis travel 10.83”
Z-axis travel 22.83”
X-axis rapid traverse rate 395 IPM
Z-axis rapid traverse rate 590 IPM
Tailstock quill center size No.3 M.T.
Tailstock quill stroke 3.94”
Tailstock quill diameter 3.54”
EQUIPPED WITH:
12” Dia. 3-jaw power chuck
Tailstock with built-in live center
12-Station turret with large amount of holders
Tool eye arm
Automatic chip conveyor
Work light
Flood coolant system
25 H.P. Spindle drive Motor
Fanuc 11T-A Control, Swivel pendant mount, Color CRT, RS232 port
NAKAMURA TOME METHODS Slant SL-3B 2-axes CNC Turning Center: NAKAMURA TOME METHODS Slant SL-3B 2-axes CNC Turning Center
Max. swing over door 22.05”
Max. swing over slide cover 27.17”
Max. swing over bed 31.1”
Max. swing over cross slide 18.9”
Max. turning diameter 15.75”
Max. turning length 21.26”
Max. distance between spindle nose and turret face 30.31”
Min. distance between spindle nose and turret face 7.48”
Hole through Spindle 3.15”
Spindle nose A1-8
Hole through draw tube 2.56”
Round collet capacity 2.50”
Spindle speed range 10 to 3500 RPM
X-axis travel 10.83”
Z-axis travel 22.83”
X-axis rapid traverse rate 395 IPM
Z-axis rapid traverse rate 590 IPM
Tailstock quill center size No.3 M.T.
Tailstock quill stroke 3.94”
Tailstock quill diameter 3.54”
EQUIPPED WITH:
12” Dia. 3-jaw power chuck
Tailstock with built-in live center
12-Station turret with large amount of holders
Tool eye arm
Automatic chip conveyor
Work light
Flood coolant system
25 H.P. Spindle drive Motor
Fanuc 11T-A Control, Swivel pendant mount, Color CRT, RS232 port
JNC 10 STAR CNC Swiss type Automatic Screw Machine w/ bar-feed: JNC 10 STAR CNC Swiss type Automatic Screw Machine w/ bar-feed
Max. machining diameter 0.394”
Stroke of headstock 2.95”
3 ranges spindle speeds 500-10,000 RPM
No. of tools: 6 (3 on each opposed tool posts) shifting
by .394” possible for 1 each
Rapid traverse rate 394 IPM
Max. cutting feed rate 236 IPM
3-Spindle end working attachment specs:
Drilling capacity 0.24”
Thread cutting capacity M6 x P1.0
EQUIPPED WITH:
Mechanical bar-feed
3-Spindle end working attachment
Threading
Twin 3-jaw work chucks
Twin tool posts
Parts separator
.15 KW OM X-axis drive
.15 KW OM Z-axis drive
.4 KW hydraulic motor
.18 KW coolant motor
1.5 KW Spindle drive
2T-A Fanuc control with RS232 port
JONES & LAMSON MODEL 4512 COMBI CNC LATHE: JONES & LAMSON MODEL 4512 COMBI CNC LATHE
MAXIMUM BAR SIZE: 4-1/2"
MAXIMUM SWING: 22"
SWING OVER CROSS SLIDE: 12-1/2"
LONGITUDINAL TRAVEL (Z-AXIS): 18"
CROSS TRAVEL (X-AXIS): 14"
MAX. DISTANCE SPINDLE TO TURRET FACE: 31"
TOOL POSITIONS: 12
TYPE OF TURRETS: END & SIDE
SPINDLE NOSE: B-1-11"
HOLE THRU SPINDLE: 5-1/4"
SPINDLE SPEEDS: (VAR.) 20 TO 1200 RPM
FEED RATES: (VAR.) .01 TO 300 IPM
RAPID TRAVERSE RATE: 300 IPM
MOTOR: 40 HP
EQUIPPED WITH:
FANUC OT CNC CONTROL
COOLANT
SPLASH/CHIP GUARDS
NOTE - MACHINE REMANUFACTURED AND RETROFIT WITH FANUC OT CNC CONTROL IN 2002.
no manuals
needs work
CNC DUAL SPINDLE TURNING CENTER : With dual Turrets
Live Tooling and Dual Sub-Spindles
Siemens 810T CNC Control with Color CRT
6.3" Swing Over the Carriage
(2) 5C Collet Chucks
Live Tooling
(2) Main Spindles
(2) Sub-Spindles
5000 RPM
Includes Dual Spindle Barfeeder!
MAZAK Quick Turn 10N-ATC-M/C CNC Slant Bed turning/milling center: MAZAK Quick Turn 10N-ATC-M/C CNC Slant Bed turning/milling center
Max. swing 17.3”
Max. cutting diameter 10”
Max. cutting length 19.69”
Spindle nose A2-6”
Spindle bore 2.2”
Tailstock quill diameter 3.15”
Tailstock center size No.40 M.T.
Tailstock quill travel 5.1”
Spindle speed range 50-5000 RPM
EQUIPPED WITH:
16 Station magazine tool changer
“C” axis
Programmable tailstock
Tool eye
8” Dia. Howa hydraulic 3-jaw power chuck
with set of soft jaws and remote foot pedal
(5) block type holders
(5) round type holders
(6) live tools
(1) live right angle tool
Misc. cutters
Flood coolant
15 H.P. Main drive motor
Mazatrol CAM T-3-B CNC control
with color CRT and graphics
1996 Citizen E16J CNC Turning Center: 5/8 Capacity
Mitz Control
6.3 Machine Length
10,000 RPM Main
8,000 RPM Sub
5,000 RPM Live Tool
(2) 12 Station Turret
c Axis
Chip Conveyor
Bar Feed
Full Machine Specifications
MAXIMUM MACHINING DIAMETER 16MM (5/8")
MAXIMUM MACHINING LENGTH 160MM (6.3")
MAIN SPINDLE THROUGH HOLE 20MM (.79")
MAIN SPINDLE SPEEDS 220 - 10,000 RPM
MAXIMUM SUB SPINDLE SPEED 8,000 RPM
MAXIMUM LIVE TOOL SPEED 5,000 RPM
MAXIMUM DRILLING DIAMETER 4MM (.157")
MAXIMUM THREDING DIAMETER M3 (.118")
RAPID SPEEDS (X1 & X2 AXES) 12 M/MIN (472"/MIN)
RAPID SPEEDS (Z1 & Z3 AXES) 16 M/MIN (630"/MIN)
RAPID SPEEDS (C AXIS) 100 RPM
MAX. CHUCKING DIA. OF PICK-OFF SPINDLE 16MM (5/8")
MAXIMUM BACKWORK LENGTH 140MM (5.51")
PICK-OFF SPINDLE SPEED 200-5000 RPM
NUMBER OF TURRETINDEXES 10 PER TURRET
SYNCHRONOUS ROTARTY GUIDE BUSHING UNIT E216J U22OZ/U212OZ
C AXIS CONTROL UNIT E2U21B
COOLANT UNIT PUMP TYPE 400W (0.54HP)
COOLANT UNIT CARTRIDGE TYPE TANK 140 LITRES (37 GAL)
EQUIPPED WITH
MITSUBISHI CNC CONTROL
(2) 12-STATION TURRETS (ALL LIVE)
C AXIS ON MAIN SPIDNLE
SUB-SPINDLE WITH 5 DEGREE INDEX
SPEGO TURNANIC 123 BAR FEED WITH Z-SORBS
LIFT UP CHIP CONVEYOR
TOOL HOLDERS
STANDARD COOLANT SYSTEM
MIST COLLECTOR (AIR PUMP FOR BAR FEED
ALL AVAILABLE MANUALS AND SCHEMATICS
12 MONTH EXTENEDED WARRANTY INCLUDED IN
1998 Mori Seiki DL-151Y CNC Turning Center with Twin Spindle & Turrets: MSC 501 Cntl
16.5' Swing
40.2" Btwn Spindle Noses
7.8" Turn Dia.
7.8’ Turn Length
1.7" Bar Cap
Dual Spindles
5,000 RPM
10 HP
12 Tools Per Turret
3,000 Rot. Tool
3.8HP
6" Chuck Both Sides
Built In Tool Pre Setter
(8) Live Tools
30 Misc. ID & OD Holders Combined Included
Full Machine Specifications
Control MSC-501
Swing Over Bed No.1, 2 16.5"
Max Distance BTWN Spindle Noses 40.2"
Max Turning Diameter No. 1, 2 7.8"
Standard Turning Diameter No. 1,2 5.9"
Max Turning Length No. 1, 2 7.8"
Bar Capacity 1.7"
Travels: X-Axis No.1, 2 9.3/8.5+/- 0.8"
Y-Axis 3.1 +/- 1.6"
Z-Axis 9.8"
2nd Head Stock 30.9"
Number of Spindles 2
Spindle Speed Range No. 1, 2 50-5,000 RPM
Spindle Nose No. 1, 2 JIS A2-5
Thru Hole Diameter 2.2"
Number of Turrets 2
Tools Per Turret 12 (All Rotary)
Rotary Tool Speed 30-3,000 RPM
Spindle Drive Motor #1/ #2 7.5HP/ 10 HP
Rot Tool Spindle HP 3.8 HP
Equipepd With:
6" Chuck Left & Right Side
Built In Tool Presetter
Chip Conveyor
(8) Live Tools
Approx (14) I.D. Tool Holders
Approx (16) O.D. Tool Holders
1998 Mazak SQT 30MS CNC Turning Center with Sub-Spindle: 15" Chuck
T-Plus Control
LNS Quickload Barfeeder
12 Position Turret
Live Tooling
Sub Spindle
35 HP
Full C-Axis
3" Bar Capacity
Conveyor
Full Machine Specifications
Mazatrol T-PLUS/CRT
Maximum Swing 22.04"
Maximum Swing (Over Carriage) 19.68"
Maximum Cutting Diameter 16.25"
Maximum Bar Diameter 3.03"
Maximum Distance Between Std. Chuck Jaws &2nd 40.4"
Spindle Nose A2-8
Spindle Bore 3.46"
Spindle Speed 3300 RPM
Spindle Indexing (C Axis) .001 degree
Spindle Motor Horsepower (30 Min.) 35 HP
Sub Spindle Speed 3300 RPM
Maximum Synchronized Speed 3000 RPM
Recommended Synchronized Transfer Speed 300
Spindle Indexing 5 Degree/ 72 Pos.
Spindle Motor Horsepower (10 Min.) 10 HP
Type of Turret Drum
Turret Index Time (sec.) 0.9 Seconds 1 position
Number of Tools/Type 12
Tool Size (Turning & Facing) 1"
Tool Size (Boring Bar Max. Dia.) 2"
Milling Spindle Speed 1500 RPM
Spindle Motor Horsepower (10 min) 10 HP
X Axis 9.625"
Z Axis 40.75"
B Axis 42"
Rapid Traverse X/Z Axis 708/944 IPM
Rapid Traverse C Axis 100 RPM
Rapid Traverse B Axis 590 IPM
Includes:
12" 3 Jaw Chuck
LNS Quickload Barfeeder
Chip Conveyor
2004 Hardinge Quest 8/51 Hydroglide CNC Turning Center: Fanuc 21iT
20HP
8,000 RPM
24” Centers
2.378” Bar capacity Tailstock
12 Station Turret
Tool Probe
Thread Cutting Cycle Retract
Continual Thread Cutting
PC Front End Machine
Foot Switch
Full Machine Specifications
Hydroglide Model- Hydrostatic Linear Guideways
Optional High Speed Wraparound Drive System (8,000
Fanuc 21iT Control
12 Station Top Plate
Tailstock
Automatic Tool Touch Probe
Collet Closer Footswitch (Main)
Thread Cutting Cycle Retract
Continual Thread Cutting
PC Front End Machine
Travels (Max) X axis 7.45”
Z axis with Collect 24”
Z axis with 8” Chuck 20.5”
Spindle Through Hole 2.378”
Turning Dia Max 12.151”
Swing Dia over Way Cover 20.44”
20 HP
80-8,000 RPM
2002 Gildemeister CTX-400-S2 CNC Turning Center with Live Tooling: Fanuc 21iT
22.4" Swing
16.5" Swing Over Crosslide
25" Centers
12 Tools
5,000 RPM
37.5 HP
Live Tooling
Full Contouring C-Axis
RS -232 Port
8" or 10" 3 Jaw Power Chuck
Prog Tailstock
Chip Conveyor
Tooling Package!!
Full Machine Specifications
LATHES, 3-AXIS CNC, UNIVERSAL W/ LIVE TOOLING
Fanuc 21i
Max Swing Over Slant Bed 22.4"
Max Swing Over Crosslide 16.5"
Distance Between Centers 25"
Travels:X-Axis 8.7"
Z-Axis 25"
Rapid Travers:X / Z-Axis 787 / 945 IPM
Tool Positions 12 Total
Spindle Bore 3.1"
Bar Capacity 2.56"
Spindle Speed Range 25-5,000 RPM
Spindle Horse Power 37.5 HP
Equipped With:Fanuc 21i Control
RS-232 Port
Tool Tip Graphics
8" or 10" 3-Jaw Power Chuck (5k RPM Only with 8")
Live Tooling Milling Drilling Turret Option
Full Contouring C-Axis
Chip Conveyor
Programmable Tailstock
2002 Hardinge Quest 6/42 CNC Turning Center: Belted
Fanuc 21iT
15HP
6,000 RPM
15” Centers
1.89” Bar capacity
Tailstock
12 ATC
Full Machine Specifications
General Precision Model
Belted Drive System
Fanuc 21iT Control
12 Station Top Plate
Tool Touch Probe
Tailstock
Travels (Max) X axis 7.45”
Z axis with Collect 15”
Z axis with 6” Chuck 10.65”
Spindle Through Hole 1.89”
Turning Dia Max 12.151”
Swing Dia over Way Cover 20.44”
15 HP
60-6,000 RPM
1999 Haas SL-20 CNC Turning Center with Live Tooling: 8" Kitagawa Chuck
20 HP
2.062" spindle bore
High Speed
5C ATC Collet Chuck
Hyd Draw Tube
Floppy
Tool Pre Setter
Live Tooling
P. Catcher
Quick Code
Chip Auger
Full Machine Specifications
Heavy Duty Servo Bar 300 Bar Feeder
Part Program Storage and Edit
8" Kitagawa Chuck # B-208
20 HP Vector Dual Drive
High Speed Machining
5C ATS Collet Chuck
Hydraulic Draw Tube
Hydraulic Tailstock
Instruction Manual
Floppy Disk Drive
Advanced Editor
Tool Pre Setter
Live Tooling
Sensor Light
Parts Catcher
Quick Code
Chip Auger
Alarms
1998 Mazak SQT-15MS CNC Turning Center with Sub-Spindle: Swing 20.9"
Turning Diam. 11.8"
21.9 Btwn Centers
25 HP
35-5000 RPM
ATS B-60 collet Chuck
Full Machine Specifications
MAZATROL T-Plus CNC Controls
Main and Sub Spindle
Maximum Swing 20.9"
Max Turning Diameter 11.8"
Between Centers 212.9"
Main Spindle Motor 25 HP
Full "C" Axis
Spindle Speed 35-5000 RPM
ATS B-60 Collet Chuck 3 Jaw Chuck
Sub Spindle Motor 10 HP
Sub Spindle Speed 180-3000 RPM
6" 3 Jaw Chick
Single Tool Turret with 12-Tool Positions
5 HP Rotary Tools
120-3000 rpm Rotary Tool Speeds
1180 IPM Rapid Transverse Rate
Accessories Tool Eye
Auto Chuck Open/ Closure
Rigid Taping Cycle
Chip Conveyor
Automatic Parts Catcher
Bar Feed Interface
Rotary & Turning Tools as Available
1988 Cincinnati Cinturn 10U40: Acramatic 850TC Control
C Axis
Live Tool
VDI50
12 Station Turret
30 HP
2.5" Bar
44" Centers
15" Swing
3500 RPM
Full Machine Specifications
Series 1210
Swing 18"
Center Distance 44"
Travels X 5.2"
Travels Z 10"
RPM 32-3500
Spindle Bar 2.3"
30 HP
12 Position Turret
10" Chuck
C Axis 1 deg
VDI 50
Live Tooling
Manuals
5 OD Holders
2 ID Holders
2 Live Holders
800 Cutting Hours
Tailstock
Max Length 44"
Has Optional 30 HP Spindle Motor
30” x 168”cc MONARCH Pathfinder N.C. Straight Bed Lathe, Model 25NC: 30” x 168”cc MONARCH Pathfinder N.C. Straight Bed Lathe, Model 25NC
Max. Swing over bed 31”
Max. Swing over cross-slide 20”
Hole through spindle 3 1/16”
Center size No.6 M.T.
Spindle nose D-1-8-Camlock
Bed width 22”
Tailstock spindle diameter 5 ¾”
Tailstock Spindle travel 10”
4 Ranges spindle speeds (Infinity variable) 10-1250 RPM
Minimum programmable increment .0001”
Longitudinal threading rates up to 150 IPM
Traverse rates up to 275 IPM
EQUIPPED WITH:
Flame hardened bed ways
Interchangeable square tool post and hexagon tool post
Tailstock
Automatic chip conveyor
12” Dia. capacity roller steady rest
Built-in live tailstock center
20” Dia. 3-jaw power chuck w/ extra jaws
Pan bed and Coolant system with sliding splash guard
Automatic coolant supply to each tool
Heavy duty cross bridge on hardened dovetail with ball screw drive
Carriage driven by preloaded rack and pinion with precision feed back and hydraulic Servo Motor
40 H.P. DC Main Drive Motor
G.E. Mark Century 7500 N.C. Controller
We found 54 matching ads. Now displaying the remaining 54 ads.
26´´ X 86´´ TOS GAP BED ENGINE LATHE: 26´´ X 86´´ TOS GAP BED ENGINE LATHE:
SWING OVER WAYS ..................... 26´´
SWING OVER CROSS SLIDE .............. 14´´
DISTANCE BETWEEN CENTERS ............ 86´´
SWING IN GAP ........................ 36´´
LENGHT OF GAP ....................... 16-1/2´´
SPINDLE SPEEDS ...................... (16) 10 TO 1000 RPM
LONGITUDINAL FEEDS .................. (38) 0.002 TO 0.0311 IPR
CROSS FEEDS ......................... (38) .0005 TO 0.028 IPR
THREADS ............................. (38) 2 TO 72 TPI
METRIC THREADS ...................... (38) .2 TO 4 MM PITCH
DIAMETER OF SPINDLE HOLE ............ 3´´
THREAD DIAL ......................... YES
SPINDLE FORWARD AND REVERSE ......... YES
HARD WAYS ........................... YES
MOTOR ............................... 7.5 HORSEPOWER
36" VERTICAL TURRET LATHE: 36" VERTICAL TURRET LATHE
DIAMETER OF 4 JAW TABLE ....... 36"
TABLE SPEEDS .................. (20) 4.93 - 180 RPM
FEEDS ......................... (16) .0026 TO .500 IPR
VERTICAL TURRET TRAVEL ........ 26"
FACE OF TURRET TO TABLE ....... 41-1/4" MAXIMUM
SWING, SIDE HEAD UP ........... 39"
SWING, SIDE HEAD DOWN ......... 45" DIAMETER
SWIVELING TURRET HEAD ......... YES
5-POSITION TURRET ON RAIL ..... YES
4-WAY TOOL POST ON SIDEHEAD ... YES
PENDANT CONTROL ............... YES
MOTOR ......................... 30 HORSEPOWER
40" VERTICAL TURRET LATHE: DIAMETER OF 4-JAW TABLE ............. 39-1/2"
SWING WITH SIDE HEAD IN PLACE ....... 42"
SWING WITHOUT SIDE HEAD ............. 50"
SPINDLE SPEEDS ...................... (16) 6.2 TO 310 RPM
MAXIMUM UNDER RAIL .................. 46"
HORIZONTAL TRAVEL OF TURRET HEAD .... 28"
VERTICAL TRAVEL OF TURRET HEAD ...... 27"
HORIZONTAL TRAVEL OF SIDE HEAD ...... 24"
VERTICAL TRAVEL OF SIDE HEAD ........ 28"
FEEDS............................... (12) .002 TO .259 IPR
EQUIPPED WITH:
5 POSITION TURRET HEAD ON RAIL
SIDE HEAD
PENDANT CONTROL
30 HORSEPOWER MAIN MOTOR
42" VERTICAL TURRET LATHE: DIAMETER .............................. 42"
SWING ................................. 46"
TABLE SPEED ........................... 4.1 TO 125 RPM
TRAVEL OF THE RAM ....................26" VERTICAL
SADDLE TRAVEL ON RAIL ................37" RIGHT TO LEFT
HEIGHT UNDER RAIL ..................... 39" (RAM HIGHEST POSITION)
SIDE HEAD WITH 4 WAY TOOL POST ........ 1-1/4" SQUARE TOOL
HORIZONTAL TRAVEL ..................... 22"
VERTICAL TRAVEL ....................... 31"
FEED RATES FOR THE HEADS .............. 12
CHANGES ............................... 1/96" TO 1/2"
RAPID TRAVERSE ........................ YES TURRET RAIL HEAD AND SIDE HEAD ........ YES
4 JAW CHUCK ........................... YES MOTOR ................................. 20 HORSEPOWER
HARDINGE Precision Second Operation Lathe, Model DSM-59: HARDINGE Precision Second Operation Lathe, Model DSM-59
Spindle capacity with
round 5C collets 1-1/16"
hexagon 5C collets 7/8"
square 5C collets 3/4"
step chucks 1-1/16" to 6"
jaw chucks 5"
jaw chucks through spindle 1-5/32"
Spindle nose 2-3/16" R.H.
Length of bed 36"
Swing over bed 9"
Travel of double tool cross slide 3 3/4"
Travel of turret slide 4"
Diameter of turret holes 5/8"
Variable spindle speeds range 230 to 3,500 RPM
EQUIPPED WITH:
Hexagon turret
Double tool cross slide with (3) toolblocks
Push button control for variable speed
Ball bearing lever collet closer
(2) Round type 5C collets
(1) Dead center
(4) Drill chucks
Work light
Self-contained coolant system
3/4 - 3/8 H.P. 3/60/220 volt 2-speed main drive motor and electrical controls
Model HC HARDINGE Precision Chucker: Model HC HARDINGE Precision Chucker
Spindle capacity:
with step chucks 1" to 6"
with jaw chucks 5"
with jaw chucks through spindle 1 5/32"
with Round 5C collets 1"
with Hex 5C collets 7/8"
with square 5C collets 3/4"
Spindle nose diameter 2.189"
Spindle nose thread 2 3/16"-10 R.H.
Maximum fixture diameter 9"
Maximum distance from face of turret to spindle 13"
Power feeds 1/4 to 10 IPM
Spindle speeds 130 to 3000 RPM
EQUIPPED WITH:
Threaded nose
Hardened and ground bedways
8-station turret
Steel cabinet
Coolant
1.5 H.P.
3/60/220 volt electrics
9" x 22"cc SOUTHBEND model A bench lathe with table: 9" x 22"cc SOUTHBEND model A bench lathe with table, bed length 3 1/2'
Collet capacity 1/2"
Max. swing over bed 9 1/4"
Max. swing over cross slide 5 1/2"
Hole through spindle 3/4"
Cross slide travel 5 7/8"
Compound rest top slide travel 2 1/4"
Tailstock spindle taper No. 2 M.T.
Tailstock spindle travel 2 1/8"
6 Spindle speeds 41-658 RPM
Longitudinal feeds .0015-.0853 IPR
Cross feeds .0004-.0252 IPR
Thread range 4-224 T.P.I.
EQUIPPED WITH:
Steel table mount
Swivel compound
Power longitudinal and cross feeds
Threading with thread dial
5” dia. 3-jaw universal chuck
3-point plain steady rest
Plain toolpost
(3) drill chucks
Live center
½ H.P. 3/60/220-440 volt motor with reversing control
Wired for 3/60/440 volt operation
9" x 22"cc SOUTHBEND Model A Bench lathe with table: 9" x 22" cc SOUTHBEND Model A Bench lathe with table, Bed length 3 1/2'
Collet capacity 1/2"
Max. swing over bed 9 1/4"
Max. swing over cross slide 5 1/2"
Hole through spindle 3/4"
Cross slide travel 5 7/8"
Compound rest top slide travel 2 1/4"
Tailstock spindle taper No. 2 M.T.
Tailstock spindle travel 2 1/8"
6 Spindle speeds 41-658 RPM
Longitudinal feeds .0015-.0853 IPR
Cross feeds .0004-.0252 IPR
Thread range 4-224 T.P.I.
EQUIPPED WITH:
Steel table mount
Swivel compound
Power longitudinal and cross feeds
Threading with thread dial
5" dia. 3-jaw universal chuck with (2) sets of jaws
3-point plain steady rest
Plain toolpost
Drill chuck
Live center
Dead center
Carriage stop
1 H.P. 3/60/220-440 volt motor with reversing control
Wired for 3/60/440 volt operation
24”/32” x 120”cc IKEGAI Removable Gap Bed Lathe: 24”/32” x 120”cc IKEGAI Removable Gap Bed Lathe
Maximum swing over bed ways 24.4”
Maximum swing over cross slide 15.35”
Maximum swing through gap 32”
Maximum length of gap from front of chuck 9”
Spindle bore 2.17”
Spindle nose type A
Bed width 16-15/16”
Tailstock spindle diameter 2-15/16”
Tailstock spindle taper No. 5 M.T.
20 Spindle speeds 25-2000 RPM
44 Longitudinal feeds 0.00136-0.0937 IPR
44 Cross feeds 0.00044-0.0315 IPR
Thread range:
Inch 2-28 T.P.I.
Metric 1 to 224 mm.
Module 0.25-56
EQUIPPED WITH:
Removable gap bed
Induction hardened bed ways
Swivel compound
Hydraulic tracer attachment (less power unit)
2-speed drilling type tailstock
Extra fine feed arrangement
15” diameter 3-jaw universal chuck
Thread dial
Carriage stop
Quick-change tool post with toolblock and tool
Work light
3-point plain follow rest
3-point 7 ½” diameter capacity steady rest
3-point 6” diameter capacity steady rest
Motor amp meter
(2) slide out chip pans with coolant pump
15 H.P. 3/60/220-440 volt motor with controls
20” x 144”cc MONARCH heavy duty engine lathe: 20” x 144”cc MONARCH heavy duty engine lathe, Mdl. 20M
Max. swing over bed ways 22 ½”
Max. swing over cross-slide 13”
Hole thru spindle 2-3/16”
Spindle nose 8”-D-1 Camlock
Size of centers No. 5 M.T.
Compound rest top slide travel 6”
Bed width 21 ¾”
Tailstock spindle diameter 4”
Tailstock spindle travel 6 ¾”
16 Spindle speeds 11 to 500 RPM
48 Feeds .0038 to .240 IPR
Thread range ¾ to 46 T.P.I.
EQUIPPED WITH:
Flame hardened bed ways
Full threading
Thread dial
Swivel compound
15” dia. 3-jaw universal chuck
12” bed extension for tailstock increasing center distance to 156”
Square toolpost
Live center
(2) Pipe centers
Power rapid traverse to carriage
Roller type steady rest
Pan & bed and coolant
25 H.P. 3/60/230-460 volt motor with controls
Wired for 3/60/440 volt operation
#3A WARNER & SWASEY Square Head Saddle Type Turret Lathe, Model M-3500: #3A WARNER & SWASEY Square Head Saddle Type Turret Lathe, Model M-3500
Maximum swing over carriage guard: 23-1/2"
Maximum swing over bed: 24-1/2"
Maximum swing over carriage horn: 18"
Bar capacity - Round: 4-1/2"
Square: 3-3/16"
Hexagon: 3-7/8"
Spindle nose: A-11"
Cross slide specs: Cross travel - 14-3/8"
16-Cross feeds - .0025 to .082 IPR
Longitudinal travel - 51"
16-Longitudinal feeds - .005 to .167 IPR
Hexagon turret specs: Longitudinal travel - 51"
16-Longitudinal feeds - .005 to .167 IPR
Diameter of holes - 5"
Maximum distance, spindle to turret face - 59"
Length turned: 43"
16-Spindle speeds: 12 to 426 RPM
EQUIPPED WITH:
Square, pre-selector headstock
Hardened ways
Square toolpost
Rapid traverse to side carriage
Telescopic way covers
Overhead pilot bar
21" Dia. 3-jaw universal chuck
Chuck guard
(2) 2-Hole vertical slide tools
(1) Multiple boring head with pilot hole
(2) Long flange type toolholders
(1) Short flange type toolholder
(3) Boring tools
Pan bed with splash guard
30 H.P. 3/60/220-440 volt motor with controls
Machine wired for 3/60/440 volt operation
No.5-3 GISHOLT Masterline Ram type turret lathe with SCR drive: No.5-3 GISHOLT Masterline Ram type turret lathe with SCR drive
Swing over bed ways 21 ¾”
Swing over carriage wings 18 ¾”
Swing over cross slide 12 1/8”
Bar capacity 3”
Bed width 12”
Spindle nose A1-8”
Cross slide travel 11 ¾”
Longitudinal travel of cross slide 25 ¾”
(8)Power longitudinal & cross feeds .003-.031 IPR
Hexagon turret turning length 15.62”
Max. distance spindle to turret face 37”
8 power longitudinal feeds of turret .003-.031 IPR
24 Spindle speeds 30-1500 RPM
EQUIPPED WITH:
Hardened bed ways
Curvic couplings on both hexagon & square turrets
Leader type threading with (5) leaders
Square front turret tool post
Hexagon turret
Mimik hydraulic tracer attachment mounted on rear slide
Pneumatic collet chuck with approx. (50) sets of collets
8 ¼” dia. 3-jaw universal chuck
Swing type pendant control
Power assisted turret indexing
Dual feeds on cross slide
(5)short flange type tool holders
(1)long flange type tool holders
(1)live center
(1) drill chuck
Pan bed and coolant
Variable speed drive with up-dated Square D-Altvar
S.S. controls, pendant control mount
3/60/440 volt control voltage
13” x 36” cc CLAUSING-COLCHESTER Geared-Head Lathe: 13” x 36” cc CLAUSING-COLCHESTER Geared-Head Lathe
Max. swing over bed 13”
Max. swing over saddle wings 12”
Max. swing over cross slide 8”
Bar capacity thru spindle 1 ½”
Spindle bore 1 9/16”
Spindle nose L-O tapered key
Cross slide travel 6 ½”
Compound rest travel 3 ¾”
Tailstock spindle diameter 1 11/16”
Tailstock spindle travel 4 ¼”
Center in tailstock No.3 M.T.
Bed width 8 1/2”
16 spindle speeds 40-1800 RPM
45 longitudinal feeds .0025-.068 IPR
45 cross feeds .0012-.034 IPR
Thread range 4-112 T.P.I
EQUIPPED WITH:
Geared head
Flame hardened bed-ways
Swivel compound
Thread indicator
Micrometer carriage stop
12” Dia. faceplate
9” Dia. 4-jaw chuck
6” Dia. 3- jaw universal chuck with
(4) sets of soft jaws
L-o back plate
Hand collet closer with nose (for 5C collets)
2-point plain follow rest
Drill chuck with adapter
Dead center
Headstock sleeve adapter with dead center
Boring bar
Steel cabinet base
Chip pan with splash guards
3/1 ½ H.P. 2-speed, 3/60/220 volt
motor with controls
21”/28-1/8” x 160”cc HERCULES AJAX gap bed lathe: 21”/28-1/8” x 160”cc HERCULES AJAX gap bed lathe
Max. swing over bed 21”
Max. swing over cross-slide 13-1/8”
Max. swing through gap 28-1/8”
Length of gap in front of face plate 6 ¾”
Hole through spindle 3-1/8”
Spindle nose D-1-8 Camlock
Cross-slide travel 14-13/16”
Compound rest tool slide travel 4-5/16”
Bed width 14 ½”
Tailstock spindle diameter 2-9/16”
Tailstock spindle travel 5-7/8”
Tailstock center size No. 4 M.T.
12 Spindle speeds 25-1500 RPM
76 Longitudinal feeds .0014 to .0559 IPR
76 Cross-feeds .0007 to .0280 IPR
Thread range:
Inch 4 to 56 T.P.I.
Metric 0.5-7.0 mm
Module 0.5-7.0 mm
D.P. 4 to 56
EQUIPPED WITH:
Removable gap bed
Hardened bedways
Taper turning attachment
Swivel compound
Inch/metric threading with (5) change gears
18” dia. 4-jaw chuck with reversible jaws
12” dia. 3-jaw universal chck with reversible jaws
(2) 10” dia. 3-point plain steady rests
ALORIS square 4-way toolpost
(1) Dead center
(2) Pipe center
Foot brake
(3) Chip pans with coolant
10 H.P. 3/60/220-440 volt motor with controls
Wired for 3/60/440 volt operation
15”/ 21 ½” x 50” cc ENTERPRISE Geared Head Gap bed lathe: 15”/ 21 ½” x 50” cc ENTERPRISE Geared Head Gap bed lathe
Max. swing over bed 15”
Max. swing through gap 21 ½”
Length of gap in front of faceplate 5 ½”
Max. swing over cross slide 9 7/16”
Spindle bore 1 9/16”
Spindle nose D-1-4 Camlock
Center size No. 3 M.T.
Cross slide travel 8 ½”
Tailstock spindle diameter 1 31/32”
Tailstock spindle travel 5 ½”
Bed width 9 ½”
16 Spindle Speeds 45-2000 RPM
40 Longitudinal .0015-.0216 IPR
40 Cross feeds .0006-.009 IPR
Thread Range:
Inch 4-60 T.P.I.
Metric .5-7.5 mm.
EQUIPPED WITH:
Geared head
Flame hardened bed-ways
Swivel compound
Inch/Metric threading
Removable gap bed
T-slotted rear rest
Thread indicator
Hand collet closer with nose
D 1-4 Camlock spindle nose
15” Dia. faceplate
8” Dia. 3-jaw universal chuck
1-axis Anilam D.R.O. (cross travel)
4” Dia. capacity 3-point plain steady rest
Foot brake
Pan bed
5 H.P. 3/60/220 Volt Motor with controls
1942 MONARCH 27N 30.5" x 108"cc Lathe: 108" Betw Centrs
30.5" Swing
30 HP
6-303 RPM
Tailstock
Coolant System
Chip Guard
Fresh Paint
* All machinery specifications must be independently verified by buyer. All machinery sales are subject to prior sale. Any agreement to purchase or sell machinery must be in writing.
Full Machine Specifications
Distance Between Centers 108"
Swing 30.5"
Weight 18000 LBS
HP 30
RPM 6-303
Equipped With
Tailstock
3 Steady Rests 12",14",18"
Bull nose Live Centers 4", 6", 7",12"
4 jaw Chuck 21"
3 Jaw chuck 18"
Coolant System
Chip Guard
Fresh Paint
24” x 30” MONARCH Series 60 Engine Lathe:
24” x 30” MONARCH Series 60 Engine Lathe
Raised in the Sand to swing over bed ways 24 ¼”
Swing over cross slide 16 ½”
Distance between centers 30”
Hole through spindle 1 9/16”
Center size No. 4 M.T.
Spindle nose 6”-D-1 Camlock
Compound rest top slide travel 4”
Width of bed 17 5/8”
Tailstock spindle diameter 3 1/8”
Tailstock spindle travel 5”
16 Spindle speeds 17-700 RPM
66 Feeds .0014-.0841 IPR
Thread range(66) 2-120 T.P.I.
EQUIPPED WITH:
Flame hardened bed ways
Swivel compound
18” Dia. 4-jaw chuck
9” Dia. 6-jaw chuck
Micro gauging dials
Aloris tool post with (8) holders
Micrometer carriage stop
(2) Bed stops with dial indicators
Live center
(2) Jacobs drill chucks
Thread dial
Work light
Pan bed and coolant
7 ½ H.P. 3/60/220-440 Volt Motor and Controls
20”/30 3/8” x 87”cc CLAUSING METOSA Gap Bed Lathe, Model C 2087: 20”/30 3/8” x 87”cc CLAUSING METOSA Gap Bed Lathe, Model C 2087
Center height 10 ¼”
Max. swing over bed 20 7/8”
Max. swing over carriage 18 7/8”
Max. over cross slide 12 5/8”
Bed width 13 ¾”
Gap length in front of faceplate 8 5/8”
Spindle bore 3 5/32”
Spindle nose D1-8 Camlock
Center taper No.5 M.T.
Cross slide travel 14”
Compound rest travel 6 ½”
Tailstock spindle diameter 2 7/8”
Tailstock spindle travel 7”
16 Spindle speeds 45-1600 RPM
55 Longitudinal feeds .0018-.052 IPR
55 Cross feeds .0005-.015 IPR
Thread range:
Inch 2-60 T.P.I.
Metric 0.5-15 MM.
Module .25-7.5
Diametral 4-120
EQUIPPED WITH:
Removable gap bed
Hardened bed ways
Inch/Metric dials
Swivel compound with T-Slot
Thread indicator
12” Dia. 3-jaw universal chuck
7 ¼” Dia. Cap. 3 point plain steady rest
4 Position carriage stop
Headstock sleeve adapter
(2) Dead centers
(3) M.T. adapters
TRAK 102, 2-axes digital readout
Dorian quick-change tool post with (7) holders and
(3) boring bar holders
Chip pan, rear splash guard and coolant system
12 HP 3/60/230 Volt Main Drive motor w/ controls
10” x 20”cc MONARCH EE Precision toolmaker’s Lathe: 10” x 20”cc MONARCH EE Precision toolmaker’s Lathe
Max. swing over bed 12 1/2”
Max. swing over cross slide 7 ¼”
Max. distance between centers 20”
Hole through spindle 1 13/32”
Spindle nose D-1-3” Camlock
Bed width 10 ½”
Compound rest top slide travel 2”
Tailstock Spindle diameter 1 ¾”
Tailstock Spindle traverse 3 ½”
Variable Spindle speed range 8 to 4000 RPM
50 feeds .005-.016 IPR
Thread range 3-184 T.P.I.
EQUIPPED WITH:
Induction hardened bed-ways
Swivel compound
D-1-3” Camlock Spindle nose
6”Dia. 3-jaw chuck
Hand collet closer with collet nose
JACOBS collet chuck
Taper turning attachment
Square Toolpost
Pan bed
5 H.P. with new AC inverter drive and controls
20”/29 ½” x 197”cc LANSING Geared Head Gap Bed Lathe, Model 20G: 20”/29 ½” x 197”cc LANSING Geared Head Gap Bed Lathe, Model 20G
Max. swing over bed 20”
Max. swing thru gap 29 ½”
Length of gap 16”
Max. swing over cross slide 12 ¾”
Spindle bore 4 1/8”
Spindle nose D1-8 Camlock
Size of centers No.5 M.T.
Dia. of tailstock quill 2 ¾”
Travel of tailstock quill 9”
Width of bed 14 ½”
16 Spindle speeds 20-1500 RPM
200 Longitudinal feeds .0009-.235 IPR
200 Cross feeds .0008-.240 IPR
Thread range:
Inch 1-240 T.P.I.
Metric .125-28 mm
Module .062-14
Diametral 2-448
EQUIPPED WITH:
Flame hardened bed ways
Removable gap bed
Geared head
Inch/Metric threading
T-Slotted rear rest
Swivel compound
17” Dia. 4-jaw chuck
16” Dia. 4-jaw chuck
15” Dia. 3-jaw universal chuck with reversible hard jaws
(2) 12” Dia. cap. 3 point roller steady rests
(2) 7” Dia. cap. 3 point roller steady rests
(2) Follow rests
Aloris tool post with (3) holders
Removable chip pans w/ coolant
15 H.P. 3/60/220-440 Volt Motor w/ controls
53”/65” x 33’cc TR135B POREBA Removable Gap Bed Lathe: 53”/65” x 33’cc TR135B POREBA Removable Gap Bed Lathe
Length between centers 394”
Max. swing over bed 53.5”
Max. swing over carriage 43.3”
Max. swing in gap 65”
Length of gap 15.3”
Bed width 26”
Spindle nose A1-11”
Spindle bore 4 1/8”
Tailstock quill diameter 5 ½”
Tailstock quill travel 12”
Tailstock quill taper No.6 M.T.
Max. work piece weight between centers 17,500 lbs
Max. work piece weight with one steady 22,000 lbs
Max. work piece weight with two steadies 24,000 lbs
21 Spindle speeds 5-500 RPM
122 Longitudinal feeds .0017-.126 IPR
122 Cross feeds .0008-.063 IPR
Thread range:
Inch ¼ to 30 T.P.I.
Metric 1-120 mm
Longitudinal rapid traverse of carriage 13 FPM
Approx. top slide travel 19 ½”
EQUIPPED WITH:
Induction-hardened bed ways
(2) Carriages with power drive to top slide, rapid traverse and thread dials
Gap bed
Swivel compounds
Swing type chuck guard
Inch/Metric threading with (7) change gears (27,44,54,57,62,68,74)
Built-in 4-way tool posts
39.37” Dia. 4-jaw chuck
36” Dia. T-Slotted Faceplate
(2) 31” Dia. cap. 3 point roller steady rests
(1) 18” Dia. cap. 3 point roller steady rests
(1) 12” Dia. cap. 3 point roller steady rests
Heavy Duty long reach boring bar with holder
(3) M.T. adapters
(2) Live centers
(1) Headstock adapter sleeve with dual center
Chip pans with coolant system
(2) Work lights
41 HP Main drive Motor with controls
28" x 120"cc AXELSON Heavy Duty Engine Lathe, Model 24 H.D.: 28" x 120"cc AXELSON Heavy Duty Engine Lathe, Model 24 H.D.
Max. swing over bedways: 28 3/4"
Max. swing over cross slide: 18 3/4"
Bed width: 26"
Hole through spindle: 2 5/16"
Spindle nose: 11" D-1
Travel of cross slide: 16 3/4"
Tailstock spindle diameter: 41/2"
Size of centers: No.5 M.T.
24 spindle speeds 6 to 555 RPM
81 feeds .004 to .300 IPR
Thread range: 1 to 30 T.P.I
EQUIPPED WITH:
Swivel compound
Camlock spindle nose
4-jaw chuck
14 3/4" Dia. capcity 3-point roller steady rest
Plain follow rest
Micrometer carriage stop
(2) Boring holders w/(1) boring bar
Pan bed with coolant tank ( less pump)
Work light
20 H.P. 3/60/220 Volt Motor
14" x 40" Enco Manual Lathe with 2-axis DRO: Accurite 2-axis DRO
14" swing Over Bed
8-5/8" swing Over Cross Slide
40" distance Between centers
20" swing Over gap
16 Spindle Speeds
90-1800 RPM Range of Spindle Speeds
1-1/2" Hole Through Spindle
MT#5 Taper of Spindle Bore
MT#3 Tailstock Quill Taper
4-1/2" Tailstock Quill Travel
7" Cross Slide Travel
22 Number Of Metric Threads
.45-7.5MM Range of Metric Threads
40 Number of Inch Threads
4-112 TPI Range of Inch Threads
(40) .0012-.0294 in/rev. Longititudinal Feeds
(40) .0003-.010 in/rev. Cross Feeds
We found 130 matching ads. Now displaying ads.1 to 75.
One (1) 1997 Leblond-Makino A77: One (1) 1997 Leblond-Makino A77
Pallet Size 24.8" x 24.8"
Max Pallet Load 2,640 Lbs
X Axis Traverse 31.5"
Y Axis Traverse 29.5"
Z Axis Traverse 30.3"
B Axis Traverse 1 Degree Indexing
Rapid Traverse (all Axes) 1181 IPM
Cutting Feeds (all Axe) 1181 IPM
Distance From Table to Spindle 3.9"-33.5"
Distance from Center to Spindle 7.1"-37.4"
Spindle Motor 30/40 HP
Spindle Speed 10,000 RPM
ATC 40 Stations
Tool Change Time 2 Seconds
Max Tool Dia 4.92"/11.8"
Max Tool Length 17.7"
Max Tool Weight 44 lbs
Fanuc Professional 3 Control (Fanuc 16)
1 Degree 4th axis
Standard Coolant Thru
Chip Conveyor
One (1) 2003 MAZAK PFH 5800: One (1) 2003 MAZAK PFH 5800
Number of Pallet Stations 6
Pallet Size 19.69" x 19.69"
X Axis Travel 28.74"
Y Axis Travel 28.74"
Z Axis Travel 29.13"
Table Indexing .001 N/C Controuring
Max Table Load 1543 Lbs
Spindle Center To Table Top 3.15"-31.89"
Spindle Drive Motor 30 HP AC
Spindle Taper CAT # 40
Spindle Speeds 15,000 RPM
Number of Ranges 2
Rapid Traverse Rate 2,362 IPM X,Y,Z
Max Programmable Feedrate 2,362 IPM
Auto Tool Change Capacity 80 Tools
Machine Weight 22,400 Lbs
Equipped With Mazatrol 640M Conversational Control
(6) Station Pallatech With (6) Pallets and (1) Load Station
Cell Controller With Version E Software
EIA/ISO Measuring System Software
EIA/ISO Programming
Tool Life Management
Tool Breakage Detection
High Pressure Superflow II Thru Spindle Coolant System
80 Tool Capacity
Monitoring System B With MP700 Probe
Performance CNC Package
Inch/Metric Conversion
Network Interface
Operator Door Interlock
N/C Rotary Table
Transformer
Work Piece Air Blast
Chip Conveyor
Adaptive Feedrate Control
Tool Life Monitoring
One (1) 2000 Kitamura HX-500i: One (1) 2000 Kitamura HX-500i
Pallet Table Size 19.7" x 19.7"
Travels X Axis 34.3"
Travels Y Axis 28"
Travels Z Axis 26"
Max Load on Table 1760 Lbs
(full 4th)
Spindle Speed 12,000 RPM
SpindleTaper CAT # 50
Tool Magazine Capacity 50 ATC
Tool Change Time 2.0 Seconds
Rapid Traverse Rates 1969 IPM
Main Motor 35 HP
Chip to Chip Time 6 Seconds
Equipped With
Fanuc 16iM CNC Control
Coolant Thru Spindle
Chip Conveyor
Solid Box Ways
All Available Manuals
Leblond Makino CNC Vertical Machining Center Model FNC-106/A30: Leblond Makino CNC Vertical Machining Center
Model FNC-106/A30
Specification Description
Table Dimensions: 23.5" x 55"
X Travel: 41"
Y Travel: 23.5"
Z Travel: 22"
Taper: #50
Spindle Speeds: 3500 RPM
ATC: 30
Equipped With:
Fanuc OM-B CNC Pendant Control
1999 BOSTOMATIC BG12G Vertical Machining Center: One (1) 1999 BOSTOMATIC BG12G
BDC 3200 Control
Longitudinal X Axis Travel 14.9"
Transverse Y Axis Travel 15.3"
Vertical Z Axis Travel 10.0"
Max Routing Speed 30,000 RPM
Tool Holding Fixture HKS 40
Tool Changer 6 Mag Spaces
Work Table Table Surface 16.6" x 13.0"
Max Table Load 154 lbs
Machine Base Polymer Concrete
Weight 6,994 lbs
HSK 30 Spindle
Grease Lubricated Motor Spindle With 30,000 min
specially for graphite and other dust raising materials
Ethernet Connection
15" Screen Color
Electronic Handwheel
Min Quanuty Lubrication
Pneumatic Over Pressure on the measuring systems
and on the motor spindle
Efficent graphite dust extraction
Tool changer
Digital drive technology
Digital measuring systems with high resolution
Operator friendly shop optimised control
3 Axis
CDAM BSC 3200 (Heidenham)
Torit Mist Extractor
Prestressed Recirculating Ball Screw For Highest Precision
Completely Enclosed Machine in order to elimiate all emissions
Largest possible front door with large window
Graphite extractor unit integrated into the machine bed
Liquid Cooled Motor Spindle
New Spindle in 2002
6900 Hours
1998 HAAS VF-3 APC Vertical Machining Center: 1998 HAAS VF-3 APC
40" X 20" X 25"
MACROS
REMOT JOG
WIRED FOR THE 4TH AXIS
CHIP AUGER
P-COOL
FLOOPY
RIGID TAPPING
10,000 RPM SPINDLE
AUTOMATIC PALLET CHANGER
COMMENTS-MACHINE WAS ONLY EVER USED TO
CUT ALUMINUM
USED MAZAK MODEL V15 CNC VERTICAL MACHINING CENTER: USED MAZAK MODEL V15 CNC VERTICAL
MACHINING CENTER
TABLE SIZE: 55.1" X 26.7"
AXIS TRAVEL: 40" - Y
20" - X
30" - Z
DISTANCE SPINDLE NOSE TO TABLE TOP: 8" MIN.
38" MAX.
SPINDLE CENTER TO COLUMN WAYS: 21.6"
DISTANCE, FLOOR TO TABLE TOP: 33.5"
MAXIMUM TABLE LOAD: 3,300 LBS.
RAPID TRAVERSE RATE: 400 IPM
WAYS: HARDENED AND GROUND RECTANGULAR
SPINDLE SPEEDS: 14 - 2000 RPM
SPINDLE NOSE: #50 MMT
TOOL STORAGE CAPACITY: 20
MAXIMUM TOOL DIAMETER:
ALL POCKETS FULL- 5"
ADJACENT POCKETS EMPTY- 17.7"
TOOL CHANGE TIME: 6.0 SECONDS
MOTOR: 15 HP DC
EQUIPPED WITH:
VICKERS 2100 ACRAMATIC CNC CONTROL
REMOTE PENDANT STATION
TRANSFORMER
COOLANT SYSYTEM
USED MAZAK MODEL V10N CNC VERTICAL MACHINING CENTER: USED MAZAK MODEL V10N CNC VERTICAL
MACHINING CENTER
TABLE SIZE: 55.1" X 26.7"
AXIS TRAVEL: 40" - X-AXIS
20" - Y-AXIS
20" - Z-AXIS
DISTANCE, SPINDLE NOSE TO TABLE: 7-7/8" MIN.
27-7/8" MAX.
SPINDLE CENTER TO COLUMN WAYS: 21.6"
DISTANCE, FLOOR TO TABLE TOP: 30.3"
MAXIMUM TABLE LOAD: 2,200 LBS.
RAPID TRAVERSE RATE: 400 IPM X,Y & Z
WAYS: HARDENED AND GROUND RECTANGULAR
SPINDLE SPEEDS: 22.4 TO 3150 RPM
SPINDLE NOSE: #45 MMT
TOOL STORAGE CAPACITY: 30
MAXIMUM TOOL DIAMETER:
ALL POCKETS FULL- 4.8"
ADJACENT POCKETS EMPTY- 6'
MAXIMUM TOOL LENGTH: 17.7"
TOOL CHANGE TIME: 6.0 SECONDS
MOTOR: 10 HP DC
EQUIPPED WITH:
MAZATROL M-1 CNC CONTROL- PENDANT
CONTROL STYLE
COOLANT SYSTEM
SPLASH/CHIP ENCLOSURE
TELESCOPING WAY COVERS
30 STATION ATC
3 axis- Bedtype Milling Machine w/ manual wheels & quill: ACER E-mill Bed Type Milling Machine
Sony 3-Axis CNC Control
Auto Lube System
C5 Ball Screws and Bearings
Built-in Coolant System
Halogen Light
Full Length Splash Guard & Chip Pan
ULTRA HIGH QUALITY ACER E-MILL MILLING
MACHINE:
5 HP "Super E" Baldor Motor
Infinite 50 ~ 3,750 RPM Speed AC Frequency Drive
HRC 52° Hardened and Ground Table
Turcite-B Coated Slide-way and Gibs
Precision Spindle w/ ABEC-7 Bearing
Meehanite Casting
Automotive Painting
Rugged 13" x 50" Table Size
1-1/4" Diameter Ball Screws with Casted Mounting
Brackets
Hardened & Ground X, Y, & Z Table Top and Bottom
to HRC 52°
XYZ Travel: 32" x 19" x 23"
N.S.T. #40 Taper
Class 7 Precision Spindle Bearing
Precision 4" Diameter Hard Chromed Quill at HRC
62°
Turcite-B Lining Saddle Ways to Reduce Metal
Wear
Max. Load on Table: 1,700 lbs.
2000 Johnsford SV-32: 2000 Johnsford SV-32
Fanuc 18M
31.5" x 20" x 24" Travel
CT-40
15 HP
24 ATC
Chip
15,000 RPM
High Speed Machining (HPCC)
RISC
Data Server
MORI-SEIKI MODEL SH-8000 HORIZONTAL MACHINING CENTER W/ FANUC CONTROL: MORI-SEIKI MODEL SH-8000 HORIZONTAL MACHINING CENTER WITH FANUC CONTROL
SPECIFICATIONS:
X axis travel: 51.2"
Y axis travel: 47.2"
Z axis travel 43.3"
Distance from table surface to spindle center: 2-49.2"
Distance from table center to spindle gage plane: 7.9"-51.2"
Working surface: 31.5x31.5"
Max workpiece swing diameter: 51.1"
Table loading capacity: 4,400 lbs.
Max workpiece height: 51.1"
Pallet surface configuration: Tapped
Table indexing time (90°/180°): 3.4/4.2 sec.
Max spindle speed: 10,000
Rapid traverse rate: 1,653 ipm
Feedrate: .01-826 ipm
Type of tool shank: CAT 50
Type of retention knob: Mori 90 deg. type
Tool storage capacity: 60 positions
Max tool diameter : 4.92"(12.6")
Max tool length: 19.7"
Max tool mass: 66 lbs.
Method of tool selection: Fixed address
Tool changing time tool to tool: 2/3 sec.
Number of pallets: 2
Method of pallet change: Turn type
Pallet changing time: 14 sec.
Spindle drive motor (30 min/cont): 40/33.5 hp
Feed motor (X/Y/Z): 7.9,9.8,9.8 hp
Coolant tank capacity: 184 gal
STANDARD ACCESSORIES:
MAPPS conversational graphic control
Load monitor C
Tool Life management
Chip conveyor inside machine (spiral type)
Coolant system
Shower coolant
Oil hole drill coolant system
Tool tip air blow system
Oil cooler
Automatic power off system
Built in worklight
Signal indicator
Hand tools
CONTROL:
Fanuc model 18Ita inluding Mori Seiki MAPPS conversational / Graphic
OPTIONAL ACCESSORIES:
6000 RPM spindle
External chip conveyor ( hinge type rear discharge )
Optical scale feedback
Through spindle coolant I/F ( center )
1000 PSI HP Cool Jet 70/30SF
CNC VERTICAL MACHINING CENTER: 4TH AXIS READY
TABLE SIZE, WORKING SURFACE --------------- 23-1/2" X 48"
TABLE TRAVEL --------------- ( X ) -------- 40"
TABLE TRAVEL --------------- ( Y ) -------- 25"
TABLE TRAVEL --------------- ( Z ) -------- 21.65"
DIST. SPINDLE NOSE TO TABLE SURFACE ------- 7.8" MIN.
DIST. SPINDLE NOSE TO TABLE SURFACE ------- 29.5" MAX.
DIST. FROM SPDL. CENTER TO COLUMN FRONT --- 25.5"
TAPER IN SPINDLE -------------------------- ISO #50
SPINDLE SPEED RANGE ----------------------- 20 TO 3600 RPM
AUTOMATIC TOOL CHANGER CAPACITY ----------- 40 TOOLS
TABLE LOAD CAPACITY ----------------------- 3307 LBS.
MAIN DRIVE MOTOR, CONTINUOUS/30 MIN. ------ 15/20 HP A.C.
EQUIPPED WITH ---
WIRED FOR 4TH AXIS
M2 MAZATROL CONVERSATIONAL CNC CONTROL
40 STATION AUTOMATIC TOOL CHANGER
HARDENED & GROUND BOX WAY CONSTRUCTION
2 SPEED RANGE GEARED HEADSTOCK
COOLANT SYSTEM
HYDRAULIC SYSTEM
1/2 HEIGHT GUARDING
WORK LIGHT
CNC VERTICAL MACHINING CENTER: CNC VERTICAL MACHINING CENTER
OVERALL SURFACE OF TABLE ------------------ 14.75" X 41.73"
WORKING SURFACE OF TABLE ------------------ 12.6" X 33"
TABLE TRAVEL -------------- ( X ) --------- 17.7"
SADDLE TRAVEL ------------- ( Y ) --------- 12.2"
HEAD TRAVEL --------------- ( Z ) --------- 11.8"
DISTANCE TABLE TO SPINDLE - ( MAXIMUM ) --- 16.1"
DISTANCE TABLE TO SPINDLE - ( MINIMUM ) --- 3.54"
SPINDLE TAPER ----------------------------- #40
SPINDLE SPEED RANGE ----------------------- UP TO 3000 RPM
TOOL STATIONS ----------------------------- 12
TOOL CHANGE TIME -------------------------- 4 SECONDS
RAPID TRAVERSE RATE ----------------------- 472 IPM
SPINDLE DRIVE, CONT./30 MIN. -------------- 5.5 HP/7.4 HP
EQUIPPED WITH ---
FANUC OM CNC CONTROL
12 STATION AUTOMATIC TOOL CHANGER
AUTOMATIC LUBRICATION
FULL GUARDING
PRELIMINARY SPECIFICATIONS SUBJECT TO VERIFICATION OR CHANGE.
2006 Haas HRT 310 CNC Rotary Table: HRT 310 SP
Wrap Around Motor
* All machinery specifications must be independently verified by buyer. All machinery sales are subject to prior sale. Any agreement to purchase or sell machinery must be in writing.
Full Machine Specifications
Repetability 10 (arc sec)
Torque (ft-Lb) 200
Runout Max 0.001"
Speeds 0.001-50
Tooling 6 std T-Slots @ 60 deg
Center Height 9.000+- 0.001
Brake Torque 500 ft-lb
Accuracy +- 15
Max Rotation/Step 999.999 deg
Worm Gear Diameter 9.40"
2003 Haas HRT 310 Rotary Table: HRT 310 SP
Wrap Around Motor
Motor Just Rebuilt
* All machinery specifications must be independently verified by buyer. All machinery sales are subject to prior sale. Any agreement to purchase or sell machinery must be in writing.
Full Machine Specifications
Torque (ft-Lb) 200
Runout Max 0.001"
Speeds 0.001-50
Tooling 6 std T-Slots @ 60 deg
Center Height 9.000+- 0.001
Brake Torque 500 ft-lb
Accuracy +- 15
Repeatability 10 (arc sec)
Max Rotation/Step 999.999 deg
Worm Gear Diameter 9.40"
PDA P/C 50 3Axis CNC Router: (3) Aixs Router
21.13" x 24.13" Table Size
2.0" Z Axis Travel
Vacuum Table
Quick Change
(2) HP
Tool Holders
Turbo Cam Control
Full Machine Specifications
Number Of Axis 3
Table Size 22" x 24"
Table has Patented vacuum scavenge/brush hold-
down system. (does not include vacuum pump)
Y- Axis Travel 24.13"
X - Axis Travel 21.13"
Z - Axis Travel 2.0"
Number Of spindles Single
Horsepower 2 @ 24,000 rpm
Max Spindle Speed 400 IPM
Quick Change Tool Holders for 1/8" shank tools, 3/8 -
Collet Capacity
Phenolic Tooling Plate
Cutter Radius Compensation
Nested Subroutines for step and repeat functions
Tooling and programming macros for test coupon-fabrication
1.2 MB, 3.5" micro floppy disc
Menu Driven or EIA RS-274-D programming
Controls TurboCam
Electrics 230/460 vac, 20/10 amps
MACHINE HAS BEEN RURFURBISHED AND HAS -
"0" HOURS OF USE
1995 Multicam 48 CNC 3 Axis Router: Spindle
48" x 96" Table
T-Lock Hold Downs
5 HP Perske Motor
PLC/Softward
Vacuum System
(2) Xtra Perske Heads
Full Machine Specifications
Number Of Axis 3
Number Of Tables 1
Table Size 48" x 96"
Table Hold Down "T" Lock Material Hold down
Number Of Spindles Single
Spindle Motor Perske 5 HP Spindle
Drive Stepper Motor
Accuracy (max speed) +/- .002/ft 4" second
Maximum Weight 800 lbs.
Controls PLC
Software includes CASmate scan / 3-D
Import / Export clean up
In/outline / router offsets. Hatch and island fill for -
engraving. Full Scanning and line conversion capa-
bilities with 3-D machine tool path generation for -
interactive "z" control on the fly
Includes (2) Extra Perske Motor Heads
1.5 HP Vacuum Pump for product hold down
Computer / Software
Monitor, HP Scanjet 3P & Printer
Electrics 220v / 60 amps
1989 Accu-Router Powermatic Series II 3 Axis CNC Router: (3)Axis
4' x 10' Table
15 HP
Single Spindle
6" Z-Axis
Fanuc GNO Series
Full Machine Specifications
Number Of Axis 3
Number Of Tables Single
Table Size 48" x 120"
Vacuum Table No
Number Of Spindles One
Z - Axis Travel 6"
Horsepower 15 / 10 - 18,000 rpm
Controls Fanuc GNO Series
Material cutPlywood & Polypropylene Plastic (starboare)
2005 Bridgeport DT480-P3 CNC Drilling & Tapping Center: Fanuc Oi-MC
Travels: 18.9" x 15.8" x 16.9"
15K RPM
7.5 HP
BT30
20 ATC
Coolant Flush & Wash Down Hose
Full Machine Specifications
Fanuc Oi-MC Control
Travels: 18.9" x 15.8" x 16.9"
Table Size: 23.6" x 15.8"
Table Max Load: 551 lbs
Rapids: 1,890 IPM
15,000 RPM
7.5 HP Direct Drive
BT-30
20 ATC- Swing Arm Option
Coolant Flush System
Coolant Wash Down Hose
2005 Liberty CNC Routers 3 Axis: 2005 Liberty CNC Router Table Size 24" x 42"
Single Table
Number of Spindles 1
Equipped with Vexta Control
Full Machine Specifications
3 Axis CNC Router For Small Parts
# Of Axis 3
Table Size 24" x 42"
Single Table
Table Hold Down(s) "T" Slots
Number Of Spindles 1
Z - Axis Travel 1"
Horsepower .05
Controls Vexta
Includes Engraver Head
1998 Techno Model HX33VBM4896010 3 Axis CNC Router: Full Machine Specifications
# Of Axis 3
Table 48" x 96"
# Of Spindles Single
Horsepower 5
Motor Make Colombo
(includes an extra 3 axis 5.5 hp Perske motor)
X-Axis Travel 96"
Y-Axis Travel 60"
Z-Axis Travel 18.7"
Controls Computer Base Controls
2002 Shoda Essetre Leonardo 4 Axis CNC Router: (4) Axis Cnc Router Working Center
60" x 120" Bed
Single Spindle
18 hp @ 14,000 rpm
Tool
Tool Changer
Compressor
Dust collector
Pod & Rail System
Hand Held Controls
COMPLETE SYSTEM
2000 Northwood Model NW-265MC1D1 Dual Table 3 Axis CNC Router: (2000) Northwood Model NW-265MC1D1
Dual 6' x 5' Table
(3) Axis
Tool Holder
14.0" Z-Axis
17.4 HP
GE Fanuc Controls
Full Machine Specifications
"UNDER A 1000 HOURS OF USE!"
Number Of Axis 3
Number Of Tables 2
Table Size 72" x 60"
Axes Travel/Speed X - Axis: 200.00"
Rapid Traverse Rate 0 to 2500" / Min.
Y - Axis: 68.0" Rapid Traverse Rate 0 to 2500" / Min.
V - Axis: 68.0" Rapid Traverse Rate 0 to 2500" / Min.
Z - Axis: 14.0" Rapid Traverse Rate 0 to 500" / Min.
Cutting Feed Rate X - Axis 1200" / Min
Y - Axis 1200" / Min
V - Axis 1200" / Min
Z - Axis 500" / Min
C-Axis 360 Degrees
Distance Between Tables 2"
Main Shank Size 1" Maximum
Collets (4) 1/4" ER-40
(4) 1/2" ER-40
(4) 3/4" ER-40
Tool Holders (12) HSK-63F Collet Chuck (RH)
Tooling Length (extended from tool holder) 4" Maximum
Cutter Diameter 4.5"
Main Spindle Power 17.4 HP (13 kw)
Spindle Speed 3600 - 18000 rpm
Shank Size (Boring Unit) 10 mm (10H7)
Boring Unit Power 2.5 hp
Boring Unit Speed 4000 rpm
Controls GE/Fanuc 160i-MA
Controls Includes Advanced Preview Control (APC)
MPG Handle, RS-232C/PCMCIA interfaces, 32k memory
(4 wire grounded)
SUPER CLEAN
We found 51 matching ads. Now displaying the remaining 51 ads.
2 HP BRIDGEPORT SERIES I VERTICAL MILL: 2 HP BRIDGEPORT SERIES I VERTICAL MILL
SURFACE AREA OF WORK TABLE ---------------- 9" X 48"
TABLE TRAVEL ------------ ( X AXIS ) ------ 36" LONGITUDINAL
SADDLE TRAVEL ----------- ( Y AXIS ) ------ 12" CROSS
SPINDLE QUILL TRAVEL ---- ( Z AXIS ) ------ 5" VERTICAL
KNEE TRAVEL ------------------------------- 16" VERTICAL
SPINDLE QUILL SPEEDS ---- ( VARI-SPEED ) -- TO 4200 RPM
SPINDLE QUILL INTERNAL TAPER -------------- R-8
HEAD TILT FRONT TO BACK ------------------- +/- 45 DEG.
HEAD TILT SIDE TO SIDE -------------------- +/- 90 DEG.
MAIN DRIVE MOTOR -------------------------- 2 HP
EQUIPPED WITH ---
ONE SHOT MACHINE LUBRICATION SYSTEM
2 HP BRIDGEPORT SERIES I VERTICAL MILL: 2 HP BRIDGEPORT SERIES I VERTICAL MILL
SURFACE AREA OF WORK TABLE ---------------- 9" X 42"
TABLE TRAVEL ------------ ( X AXIS ) ------ 30" LONGITUDINAL
SADDLE TRAVEL ----------- ( Y AXIS ) ------ 12" CROSS
SPINDLE QUILL TRAVEL ---- ( Z AXIS ) ------ 5" VERTICAL
KNEE TRAVEL ------------------------------- 16" VERTICAL
SPINDLE QUILL SPEEDS ---- ( VARI-SPEED ) -- TO 4200 RPM
SPINDLE QUILL INTERNAL TAPER -------------- R-8
HEAD TILT FRONT TO BACK ------------------- +/- 45 DEG.
HEAD TILT SIDE TO SIDE -------------------- +/- 90 DEG.
MAIN DRIVE MOTOR -------------------------- 2 HP
EQUIPPED WITH ---
SONY 2 AXIS DIGITAL READOUT
CHROME WAYS
ONE SHOT MACHINE LUBRICATION SYSTEM
LONGITUDINAL POWER FEED .75 TO 30 IPM
RAPID TRAVERSE
COLLETS
WORK LIGHT
64” GIDDINGS & LEWIS Hypro Vertical Boring Mill, Type 64: 64” GIDDINGS & LEWIS Hypro Vertical Boring Mill, Type 64
Flush floor design, no pit required
Diameter of table 62”
Max. swing 67”
Max. height under cross rail 55”
Ram head vertical travel 32”
Turret head vertical slide travel 27”
Swivel of ram head ±60º
Center line to housing face 15”
Bore size in left ram 2 ¾”
Bore size in turret 2 ¾”
Table top to floor level 30”
(16) Table speeds 3.3 to 90 RPM
16 Feeds .003-.500 IPR
EQUIPPED WITH:
T-Slotted table w/ set of (4) faceplate jaws
L.H. Swivel ram head with 1 H.P. Dumore grinding spindle and
LH10 Sony2-axes D.R.O.
R.H. pentagon turret head with manual indexing and LH10 Sony 2-axes D.R.O.
Roller table bearings
Electric rail clamping
Power rapid traverse
Pendant control (replaced new 1988)
Automatic lubrication
(4) Square tool holders
(3) Boring bars
50 H.P. 3/60/440 Volt Main drive Motor with
control cabinet (replaced new 1988)
Height to top of Machine: 10’8”
Height above pendant control: 12’11”
Knee Mill Large 11" x 52" table: (1)Preowned SUPERMAX Vertical Milling Machine, Mdl YCM-2VAS
Table working surface 11”x52”
Number of t-slots 3
Range: Longitudinal(x) 40”
Cross(y) 16”
Vertical, knee(z) 18”
Quill 5 1/2”
(12)Longitudinal & cross feeds 5/8 to 28-3/4 I.P.M.
Rapid traverse rate, longitudinal & cross 118 I.P.M.
Rapid traverse rate, vertical 1/3 of longitudinal rate
Maximum/Minimum distance, 0”-22 3/4”
spindle nose to table
Maximum/Minimum distance, 27 11/16”- 6 11/16”
spindle center to face of column
Ram travel, approx. 21 ¼”
Turret rotation 360°
Head tilt left to right 90°
Quill diameter 4 3/8”
(3) Power quill feeds 0.0015,0.003,0.005 I.P.R.
Infinitely variable spindle speeds, two ranges 85-3800 R.P.M.
Spindle taper No.40 N.S.T.
EQUIPPED WITH:
Hardened and ground square ways
Power and longitudinal cross feeds
Power rapid traverse for longitudinal, cross and knee feeds
Swivel; overhead ram
Work light
Mist coolant
Pendant control
3-axes Acu-Rite Quik Count D.R.O.
Operator’s control pendant
Self-contained coolant system
1 H.P. Vertical feed motor
2 H.P. Table feed motor
5 H.P. 3/60/220-440 Volt AC inverter spindle drive motor and electrical controls
CARLTON CNC FLOOR TYPE BORING MILL: CARLTON CNC FLOOR TYPE BORING MILL
SPECIFICATIONS:
BAR SIZE........................: 5 "
X TRAVEL........................: 195"
Y TRAVEL........................: 94"
Z TRAVEL........................: 40"
W TRAVEL........................: 29"
SPINDLE HORSE POWER.............: 25
SPINDLE PRM.....................: 1,000
SPINDLE TAPER...................: NO.50 N.S.T.
FLOOR PLATE LENGTH..............: 20'
EQUIPPED WITH :
HARDENED & GROUND BED & COLUMN WAYS
POWER DRAW BAR
ALLEN BRADLEY 7300 CNC CONTROLS
OPERATORS STATION (ELEVATING)
RETRACTABLE WAY COVERS
AUTOMATIC WAY LUBRICATION
COOLANT SYSTEM
LIFT UP CHIP CONVEYOR
4´´ LUCAS HORIZONTAL BORING MILL: 4´´ LUCAS HORIZONTAL BORING MILL:
DIAMETER OF SPINDLE ...................... 4´´
AREA OF TABLE ............................ 40´´ X 84´´
STROKE OF SPINDLE ........................ 36´´
VERTICAL SPINDLE TRAVEL .................. 48´´
TABLE CROSS TRAVEL ....................... 60´´
MAXIMUM DISTANCE SPINDLE TO OUTBOARD ..... 96´´
SPINDLE SPEEDS ........................... (26) 9 TO 1200
FEEDS .................................... (81) .001 TO 1.038
4 WAY BED MACHINE ........................ YES
RAPID TRAVERSE ........................... YES
PENDANT CONTROL .......................... YES
OUTBOARD SUPPORT ......................... YES
MOTOR .................................... 20 HORSEPOWER
5" #350-T GIDDINGS & LEWIS Table type Horizontal Boring Mill: 5" Table type Horizontal Boring Mill
Main Spindle Specs:
Diameter 5"
Taper in spindle No.6 M.T.
Longitudinal travel 36"
Max. distance top of table to spindle center 60"
Min, distance top of table to spindle center 4 3/4"
36 Speeds 6.25 to 375 RPM
18 Feeds .005 to .250 IPR
Center distance between spindles 8.75"
High Speed Spindle Specs:
Diameter 2"
Taper in spindle No.4 M.T.
Longitudinal travel 9"
Max. distance top of table to spindle center 4"
36 Speeds 25 to 1500 RPM
18 Feeds .001 to .062 IPR
Headstock vertical travel 60"
Table working surface 48" x 86"
Table cross travel 72"
Table longitudinal travel 54"
Rapid traverse rate 120 IPM
EQUIPPED WITH:
Power rapid traverse
2-axes Tri-onics digital readouts
2”Dia. aux. High speed Spindle
Scales and verniers
15 H.P. 3/60/220-440 Volt Motor and Controls
(all ways have been remachined)
4" LUCAS 42B-60 Table type Horizontal Boring Mill: 4" Table type Horizontal Boring Mill
Diameter of spindle 4"
Taper in spindle No.50 power lock
Spindle traverse 36"
Headstock vertical travel 48"
Table working surface 40" x 74"
Table cross travel 60"
Table longitudinal travel with tailstock 51"
Table longitudinal travel without tailstock 64"
Max. distance, spindle nose to tailstock support bearing 96"
26 Spindle speeds 9-1200 RPM
81 Feeds .0001-1.038 IPR
EQUIPPED WITH:
Tailstock (less drive shaft)
Simple pendant control
Power rapid traverse
Power 50 tool-lock with No.40 adapter
Scales & verniers
2-axes Mitutoyo digital readouts
No.50 taper boring head
Built-in 4-way bed (60" width)
Coolant tank and pump
20 H.P. 3/60/220-440 volt motor with controls
70" Mdl. SK16, TOS Vertical boring mill: 70" Mdl. SK16, TOS Vertical boring mill
Table diameter 63.78"
Maximum swing when turning with side head 66.93"
Maximum swing without side head 74.5"
Maximum height under cross rail 54.33"
Maximum turning height under rail 50.79"
Maximum vertical distance, side head toolholder to table 39.37"
Vertical travel of cross rail 37.4"
Vertical travel of L.H. ram 31.5"
Vertical travel of R.H. turret slide 24.8"
Horizontal travel of side head ram 24.8"
Maximum table load capacity 11,000 lbs.
Swivel of L.H. ram head on rail ±45°, -35°
Infinitely variable table speeds 3.55 to 150 RPM
24 Feeds .0024 to 0.36
Rapid traverse rate 79 IPM
EQUIPPED WITH:
T-slotted table with set of (4) H.D. faceplate jaws
LH swivel type ram head with square toolholder
RH pentagon turret head
RH side head with square toolholder
SCAN-O-MATIC Hydraulic copying attachment mounted on LH ram head
Infinitely variable table speeds
Pendant control
Power rapid traverse, all travels
Power rail clamping
Scales, all travels
Centralized lubrication system
(2) Square toolholders for turret
50 HP 3/60/380 volt variable speed commutator main drive motor with controls
Maximum height, rail up: 186"
57" TITAN SC1600 Vertical Boring Mill: 57" TITAN SC1600 Vertical Boring Mill
Diameter of table 57"
Max. swing without side head 61"
Max. swing with side head 61"
Max. height of workpiece 47.24"
Max. weight of workpiece 17,600 lbs.
Max. travel center of R.H. head from table center 31.5"
Max. travel center of L.H. head from table center 31.5"
Vertical travel of turret head slide 29.92"
Vertical traverse of L.H. ram head 39.37"
Swivel of rail heads ± 35°
Turret tool bore diameter 3.15"
Side head vertical travel 43.3"
Side head horizontal ram travel 27.56"
Vertical traverse of cross rail 39.37"
16 Table speeds 4-200 RPM
16 feeds .00197-.197 IPR
Rapid traverse rate to heads 98.5 IPM
Rapid traverse rate to cross rail 15.75 IPM
Top of table to floor 35.43"
EQUIPPED WITH:
4-jaw chuck with set of (4) hardened top jaws and (2) sets of risers
L.H. swivel type ram head on rail with square toolholder
R.H. swivel type pentagon turret head on rail with manual indexing
R.H. side head with square toolholder and 1-axis Itek digital readout
Hydraulic rail clamping
Power rapid traverse
Motorized rail elevation
Threading and taper turning attachment with change gears
Full pendant control
Motor amp meter
Roller table bearings
Centralized lub system
Scales and verniers
Turret tooling including: (8) turret boring bars, (6) square turret toolholders, (8) boring bars, drill holder
Misc. tooling
5.5 H.P. rail elevation motor
4 H.P. rapid motors
60 H.P. A.C. main drive motor and controls Height over pendant, 168” height over ram head with rail and head in max. position
46?BULLARD Dynatrol Hi-Column Vertical Boring Mill: 46?BULLARD Dynatrol Hi-Column Vertical Boring Mill
Diameter of table 46?Max. swing 58?Max. height under cross rail 64?Vertical travel of cross rail 54?Vertical ram travel of rail head 51?Max. distance center of table
to center of ram 26 ½”
Center line of table to face of
Bed ways 19?Swivel of ram head ?30?Distance top of table to floor 37?2 ranges of infinitely variable
table speeds 27.7-83.2 RPM
111-333 RPM
Infinitely variable feed rates .001-.250 IPR
Rapid traverse rate 108 IPM
EQUIPPED WITH:
4-jaw chuck with set of hardened top jaws
11?Heavy duty R.H. Swivel type ram
head on rail with increased ram travel of 51?T.D.A. attachment for threading, angular turning,
drum scoring with approx. (14) change gears
Constant cutting speed control
Model 270Scan-O-Matic 2-axis hydraulic
Tracer attachment with power pak
Power rail clamping
Power rapid traverse
Hardened, chromed strips on cross rail
and ram head slide
Centralized pendant control with pistol grip and
speed and feed selection
Trak 102 2-axis digital readouts
Flood coolant system with pan, splash guards and pump
(4) ram tool holders
(4) ram boring bars
50 H.P. 240 Volt DC, 650/2000 RPM Main Drive Motor;
3:1 constant horsepower and 10:1 constant torque
C-600 Westinghouse Variable speed Drive control with
regenerative braking with 3/60/230-460 Volt hook-up
Max. height over ram head with everything in max. positions: 205?
Floor space required: 122”LR x 166”FB (Machine & Drive) 86”LR x 18”FB x 90”High (Cabinet)
40" x 50" DEVLIEG Type "AM" Air-Lift Index Type Rotary Table: 40" x 50" DEVLIEG Type "AM" Air-Lift Index Type Rotary Table
Working Surface of table 40" x 50"
(7) Parallel tee slots
(3) Cross reference slots
(24) Lock bolt Positions : 4@ 30 degrees, 4@ 45 degrees, 4@ 60 degrees,
4@ 90 degrees, plus 67.5; 247.5; 75; 255; 105; 285; 112.5; 292.5
degrees
Free turning with air lift
Table work piece capacity 15,000 lbs.
40" x 44 " Table base plate
Overall height 10-3/4"
48” x 48” LUCAS T-Slotted Airlift Rotary Table: 48” x 48” LUCAS T-Slotted Airlift Rotary Table
Size of platen: 48” x 48”
Height: 12 ¼”
(6) T-slots w/7”cc
Graduated in ½ degrees
Manual clamping
Approx. weight capacity: 15,000 lbs.
54” SCHIESS Vertical Turret Lathe, Model 13EK125: 54” SCHIESS Vertical Turret Lathe, Model 13EK125
Diameter of table 47 ¼”
Max.swing, with side head below table 55”
Max.swing, with side head in position 52”
Max.height under cross rail 43”
Max.turret head slide travel 28”
Max.distance, table to turret face 52”
Horizontal travel of side head ram 26”
Max.distance between table and bottom of side head ram 32”
Vertical travel of cross rail 30”
Max.weight of work piece 8,800 lbs.
12 Table speeds 8 to 126 RPM
8 Feeds .004 to .196 IPR
Rapid traverse rate 89 IPM
Swivel of turret head ±45º
EQUIPPED WITH:
T-slotted table with set of (4) faceplate jaws
Swivel type pentagon turret head on rail with (3) toolholders
Side head with square toolholder
Power rapid traverse
Motorized rail elevation
Pan and coolant
40 H.P. 3/60/220-440 Volt Motor with controls
5” LUCAS 542B-120 Table Type Horizontal Boring Mill: 5” LUCAS 542B-120 Table Type Horizontal Boring Mill
Diameter of spindle 5”
Taper in spindle No.50 power tool lock
Spindle travel 36”
Headstock vertical travel 96”
Table working surface 48” x 122”
Table cross travel 120”
Table longitudinal travel 70 3/8”
Length of bed ways 122”
Width across 4 bed ways 120”
Saddle length 216”
Spindle speeds 10-1220 RPM
42 Feeds .0001-1.038 IPR
Rapid traverse rate 112 IPM
EQUIPPED WITH:
Air-lift to table and saddle
10’ length bed
All hardened ways
Built-in 4-way bed
Multiple pendant control with pre-selection
Of speeds and feeds
Threading attachment with (23) change gears
Power rapid traverse
3-axes Mewall DP7 Digital readouts
(1) No.50 end mill holder
30 H.P. 3/60/220-440 Volt Motor w/ controls
: 84” KING Hi-Column Vertical Boring Mill, lot 481
Flush floor design, no pit required
Diameter of table 80”
Max. swing 84”
Max. height under cross-rail 72”
Max., height under ram tool holder 70 ½”
Max., height under turret face 82”
Max. height under turret tool holder 77”
Ram travel 72”
Turret head slide travel 45”
Swivel of ram head ±60º
Swivel of turret head ±30º
Distance table top to floor level 36”
16 table speeds 3.1 to 100 RPM
24 fine feeds .003-.500 IPR
EQUIPPED WITH:
T-Slotted table with set of (4) H.D. faceplate jaws
L.H. Swivel turret head with square tool holder
R.H. Swivel type pentagon turret head with manual index
and large assortment of tool holders and boring bars
Pendant controlled hydraulic speed shifting
Motorized rail clamping
Fine feeds
Power rapid traverse
2-Axes Acu-Rite digital readout on turret head
Timken table spindle bearings
12” extra column height
Extra ram and turret head travels
Scale and Verniers
50 H.P. 3/60/440 Volt Main Drive Motor and controls
Max. height over ram head 17’9”
Max. height over pendant control 14’7”
Floor space required: 17’10” LR x 13’8” FB
2 H.P. Series I BRIDGEPORT Vertical Milling Machine: 2 H.P. Series I BRIDGEPORT Vertical Milling Machine
Table working surface: 9” x 48”
Number of T-slots: 3
Range:
longitudinal 32 ½”
cross 12”
vertical, knee 16”
quill 5”
Maximum/minimum distance, spindle nose to top of table: 18 ½” / 2 ½”
Maximum/minimum distance, centerline of spindle to face of column 18 ¾” / 6 ¾”
Ram travel: 12”
Head tilt, left & right: 90°
Head tilt, front to rear, each way: 45°
Turret rotation: 360°
(3) Power quill feeds: .0015, .003, .006 IPR
Infinitely variable spindle speeds, two ranges: 60-4,200 RPM
Spindle taper: R-8
Maximum collet capacity: ¾”
EQUIPPED WITH:
Chrome ways
9” x 48” Table
Bridgeport X-axis power table feed
2-axes Acu-Rite D.R.O.
Bijur one-shot lubrication system
Work light
2 H.P. 3/60/200/220/440
2 H.P. Series I BRIDGEPORT Variable Speed Vertical Mill: 2 H.P. Series I BRIDGEPORT Variable Speed Vertical Mill
Table working surface 9” x 42”
Number of T-Slots 3
Range: Longitudinal 26 ½”
Cross 12”
Vertical, knee 16”
Quill 5”
Max./Min.distance, spindle nose to table 25 ½”/9 ½”
Max./Min.distance, centerline of spindle to face of column 18 ¾”/6 ¾”
Ram travel 12”
Head tilt, left to right 90º
Head tilt, front to rear, each way 45º
Turret rotation 360º
(3) power quill feeds .0015, .003, .006 IPR
Infinitely variable spindle speeds, two ranges 60-4200 RPM
Spindle taper R-8
Max. collet capacity ¾”
EQUIPPED WITH:
Chrome ways
9”x42” table with Bridgeport power feed and rapid traverse
Bijur one-shot lubrication
Pneumatic power draw-bar
2-axis Acu-Rite III digital readouts
Assortment of collets
7” Column riser
2 H.P. 3/60/208/220/440 Volt Motor
#5 CINCINNATI Universal Wide-Knee, High Power Mill: #5 CINCINNATI Universal Wide-Knee, High Power Mill
Table working surface: 20”x 941/2”
Range: longitudinal: 50”
cross: 14”
vertical(knee): 19”
Taper in spindle: No.50
Max.height, horiz.spindle center to table top: 19 3/4”
24 Spindle speeds: 14 to 1400 RPM
32 longitudinal and cross feeds: 3/8 to 90 IPM
32 vertical feeds: 3/32 to 221/2 IPM
Rapid traverse rate: 150 IPM
EQUIPPED WITH:
Universal swivel table
Dynapoise overarm
(1) arbor support
Power rapid traverse
Automatic backlash eliminator
Dual rear controls
(2) table dogs
Coolant system
(1) No.50 holder with manual draw bar
(1) Dividing head with 3-jaw chuck
Power speed and feed change
25 HP 3/60/220-440 volt main drive motor with controls
FU 400 V/2 HECKERT Universal Mill with H.D. Vertical Milling Attachmen: FU 400 V/2 HECKERT Universal Mill with H.D. Vertical Milling Attachment
Table working surface: 16" x 63"
Table swivel: + or - 45 degrees
Range: Longitudinal 44"
Cross 13.5"
Vertical 16"
Taper in both spindles: No. 50
Table load capacity: 3,300 lbs.
Spindle speed range: 28 to 1400 RPM
Longitudinal and cross feeds: .63 to 31.5 IPM
Vertical feeds: .2 to 10 IPM
EQUIPPED WITH:
Swivel table
Hardened knee ways
3-Axes automatic cycle control
Anti-backlash eliminator
Power rapid traverse
Pendant control
Heavy duty right angle milling attachment with 90 deg. swivel,
No. 50 taper, driver and manual draw bar
Universal right angle milling attachment with double swivel, No. 40
taper, O.H. arbor support, manual draw bar
12-3/8" Dia. Heckert t-slotted manual or power driven
rotary table, graduated in degrees, 5-1/4" overall height
Power take-off drive unit for rotary table
(2) arbor supports
Gear Box for driving dividing head
(2) Angle plates
(5) No. 50 toolholders
(3) No. 50 arbors with spacers
(1) 5" Dia. cutter
(1) Jacobs drill chuck
Work light
Coolant system
Central lubrication system
15 H.P. spindle drive motor
2 H.P. Series I BRIDGEPORT Vertical Milling Machine: 2 H.P. Series I BRIDGEPORT Vertical Milling Machine
Table working surface: 9” x 42”
Number of T-slots: 3
Range:
longitudinal 26 ½”
cross 12”
vertical, knee 16”
quill 5”
Maximum/minimum distance, spindle
nose to top of table: 18 ½” / 2 ½”
Maximum/minimum distance, centerline
of spindle to face of column 18 ¾” / 6 ¾”
Ram travel: 12”
Head tilt, left & right: 90°
Head tilt, front to rear, each way: 45°
Turret rotation: 360°
(3) Power quill feeds: .0015, .003, .006 IPR
Infinitely variable spindle speeds, two ranges: 60-4,200 RPM
Spindle taper: R-8
Maximum collet capacity: ¾”
EQUIPPED WITH:
Bridgeport X-axis power table feed
Bijur mist coolant
Bijur one-shot lubrication system
Work light
2 H.P. 3/60/200/220/440
JNC 16 STAR CNC Swiss type Automatic Screw Machine w/ bar-feed: JNC 16 STAR CNC Swiss type Automatic Screw Machine w/ bar-feed
Max. machining diameter .63”
Stroke of headstock with fixed bushing .063”
Stroke of headstock with Synchronized rotary bushing 3.74”
3 ranges spindle speeds 375-7500 RPM
No. of tools: 6 (3 on each opposed tool posts) shifting
by .394” possible for 1 each
Rapid traverse rate 315 IPM
Max. cutting feed rate 236 IPM
3-Spindle end working attachment specs:
Drilling capacity .314”
Thread cutting capacity M8 X P1.25
EQUIPPED WITH:
Mechanical bar-feed
3-Spindle end working attachment
Threading
Twin 3-jaw work chucks
Twin tool posts
Parts separator
.4 KW OM X-axis drive
.4 KW OM Z-axis drive
.4 KW hydraulic motor
.18 KW coolant motor
2.2 KW Spindle drive motor
2T-A Fanuc control with RS232 port
SWISS TYPE CNC LATHE: STAR SR-16 SWISS TYPE CNC LATHE, Model SR-16
MACHINING CAPACITY:
Maximum Turning Diameter 16 mm (5/8")
Maximum Head Stock Stroke 205 mm (8")
Maximum Drilling Capacity Stationary Tool: 8 mm (5/16")
Maximum Drilling Capacity Power Driven Attachment: 5 mm (3/16")
Maximum Tapping Capacity Stationary Tool: M8 x Pl.25
Maximum Tapping Capacity Power Driven Attachment: M5 x PO.8
Maximum Milling Capacity 0 mm (3/8")
Maximum Die Cutting Capacity M8 x Pl.25
Maximum Slotting Capacity 1.5 mm Width x 4 mm Depth
CONTROL AXIS SPECIFICATIONS:
Rapid Feed Rate - X 12,000 mm/min.
Rapid Feed Rate - Y 16,000 mm/min.
Rapid Feed Rate - Z 18,000 mm/min.
Rapid Feed Rate - XB 18,000 mm/min.
Rapid Feed Rate - ZB 18,000 mm/min.
Maximum Turning Feed Rate - X 6,000 mm/min.
Maximum Turning Feed Rate - Y 6,000 mm/min.
Maximum Turning Feed Rate - Z 6,000 mm/min.
Maximum Turning Feed Rate - XB 6,000 mm/min.
Maximum Turning Feed Rate - ZB 6,000 mm/min.
Minimum Input Increment - X .001mm/.0001" (Diameter Value)
Minimum Input Increment - Y .001mm/.0001" (Diameter Value)
Minimum Input Increment - Z .001mm/.0001"
Minimum Input Increment - XB .001mm/.0001" (Diameter Value)
Minimum Input Increment - ZB .001mm/.0001"
Operation Mode Right Handed Machine
HEADSTOCK SPECIFICATIONS:
Spindle Speed 10,000 RPM
Speed Control S Code + Direct 5 Digit Command
Main Spindle Rotational Control Inverter Control
Main Spindle Minimum Indexing Angle 15 Degrees (24 Divisions)
Main Spindle Bore 20 mm (49/64")
SUB-SPINDLE SPECIFICATIONS:
Pick-Up Capacity
Maximum Chucking Diameter 16 mm (5/8")
Maximum Part Length for Front Ejection 80 mm (3-1/8")
Maximum Parts Projection Length 30 mm (1-5/32") Distance from Collet End
SPINDLE SPECIFICATIONS:
Spindle Speeds 400 - 6,000 RPM
Speed Control S Code + Direct 4 Digit Command
Rotational Control Inverter Control
Spindle Minimum Indexing Angle 15 Degrees (24 Divisions)
Sub Spindle Motor .75 KW / 1.2 KW (30 Min.)
Collet Type R16
TOOL POST SPECIFICATIONS:
Type: Gang Tool Post - 2 Axis Control
Number of Turning Tools 6
Number of Power Driven Tools 3
Tool Shank Size 12 x 95-120 / 12.7 x 95 - 120
POWER DRIVEN ATTACHMENT:
Spindle Speed 350 - 5,000 RPM
Speed Control S Code + Direct 4 Digit Command
Rotational Control Inverter Control
Motor .4 KW
Use Cross Drilling/Milling Spindle
COLLET CHUCK & GUIDE BUSHING:
Main Spindle Collet Chuck
Type R16 (Schaublin Type F20, Art No. 87)
Stationary Guide Bushing:
Standard Version: Type VNC20
(Star Standard Part Equivalent to C16)
Revolving Guide Busing:
Standard Version: Type R16
(Weukomm Type B Art No. 39.001)
C16 Version: Type VNC29
(Star Standard Part Equivalent to C16)
HYDRAULIC UNIT SPECIFICATIONS:
Installation Method Installed Separately Outside Machine
Hydraulic Tank Capacity 20 L (5.2 Gallons)
Normal Pressure 35 kg/cm²
Suitable Hydraulic Oil Viscosity Grade: ISO V632
Recommended Oil Shell Tellus Oil 32
Hydraulic Pump Motor .75 KW
COOLANT UNIT SPECIFICATIONS:
Installation Method Installed Separately Outside Machine
Coolant Tank Capacity 100 L (26.4 Gallons)
Safety Device Coolant Oil Level Detector
Cutting Oil Water Insoluble Cutting Oil
Coolant Motor .18 KW
LUBRICATING UNIT SPECIFICATIONS:
Lubrication Part Rectilinear Guide Bearing Portion
Oil Ejection Amount 2.5 cc/30 min.
Tank Capacity .8 L (.2 Gallons)
Safety Device Lubricating Oil Level Detector
Pump Motor 3 W
Suitable Lubricating Oil Viscosity Grade ISO VG68
Recommended Oil Mobil Vactra Oil No. 2SLC
3 SPINDLE END WORKING ATTACHMENT:
Number of Tools 3
Maximum Drilling Capacity 8 mm (5/16")
Maximum Tapping Capacity M8 x Pl.25
Maximum Chucking Diameter ER16 10 mm (.39")
Maximum Die Cutting Capacity M8 x Pl.25
Maximum Die Diameter 2.5 mm (.98")
3 SPINDLE UNIT FOR BACK WORKING:
Number of Tools 3
Maximum Drilling Capacity 7 mm (1/4")
Maximum Chucking Diameter 10 mm (.39")
Maximum Tapping Capacity M6 x Pl.0
Maximum Chucking Diameter ER11 7 mm
EQUIPPED WITH:
Fanuc 16TTA Control
Sub-Spindle 15 Degree Indexing Unit with Synchronous Phase Control of
Main Spindle and Sub-Spindle
Air Blow in Sub-Spindle to Clear Chips
Broken/Cut-Off Tool Detector
Tool Pre-Setter
NSK Air Spindle Milling Heads with 30,000 RPM Air Motors
(3) Air Motors
LNS Mini-Sprint S2 Barfeed, Serial #46826-96
EQUIPPED WITH: (CONTINUED)
Door Interlock
Back Working Attachment
Broken Belt Detector for Sub-Spindle
Machine Manuals
Interior Work Light
Cabinet with Assorted Tooling & Collets
3-Spindle Cross Drilling/Milling Unit
Parts Ejection Detector
Sub-Spindle Digital Tachometer
Main Spindle Inner Tube: 11.7 mm
Revolving Guide Bushing
2.2 KW (Continuous) Main Spindle Motor
DIMENSIONS:
Main Machine: 84" L-R x 45" F-B x 84" H
Barfeed: 184" L-R x 44" F-B x 50" H
Tooling Cabinet: 30" L-R x 30" F-B x 34" H
Coolant System: 44" L-R x 30" F-B x 17" H
KSI 7 - Axis CNC Swiss Lathe: KSI 7 - Axis CNC Swiss Lathe
Bar Capacity
MAIN :32mm Max Turning Bar Dia.
210 mm Max Turning Bar Length
SUB: 32mm Max Chucking Dia.
Control
Fanuc 18iTB
Features/Accessories/Attachments
Y Axis Tool Block (adds 3 front working ID Tools)
9 Driven Tools
Full Contouring “C” Axis On Main & Sub Spdl.
Rigid Tap All Spindles
Low Hours
Comments
with: Parts Conveyor
Iemca Mini Boss Magazine Bar Feed S/N A05031604
Coolant System
Manuals
* 8000 RPM Spindle Speeds Main & Sub Spdl.
1 Deg. / 1000 Spindle Positioning Main & Sub
Rapid Traverse: 32M / Min - All Axes
Electrics: Main Spindle: 5.5 / 7.5 KW
Sub Spindle: 1.5 / 2.2 KW Cross Drill/Mill Unit Motor: 0.75/1.5 hp Rotary Guide Bushing Unit: 0.75/1.5 hp
We found 15 matching ads. Now displaying the remaining 15 ads.
8' x 22" CARLTON Radial Drill: 8' x 22" CARLTON Radial Drill
Arm length: 8'
Diameter of column: 22"
Maximum spindle radius: 9'3"
Minimum spindle radius: 2'6"
Max.distance, spindle to base: 98"
Min.distance, spindle to base: 20 1/2"
Working surface of base: 61"W x 102"L
Overall length of base: 170" x 70"W
Height of base: 12 1/2"
Vertical travel of spindle in head: 24"
Spindle diameter: 4"
Taper in spindle: No.6MT
Traverse of arm on column: 531/2"
Traverse of head on arm: 81"
36 spindle speeds: 8 to 800 RPM
18 feeds: .004 to .125 IPR
Tap leads: 8,11, 14, 18 TPI
EQUIPPED WITH:
(NEW) Spindle installed 2002
281/4" x 321/4" x 24" High, Carlton T-slotted, Tilting box table
T-slotted base
Power rapid traverse to head
Power column clamping
Hardened wear strip on arm
25 H.P. 3/60/220-440 Volt Main Drive Motor with controls
Max. height over column cap: 13'8"
Max. height over head: 14'7"
#140U KAUKAUNA Universal Radial Drill on Bed: #140U KAUKAUNA Universal Radial Drill on Bed
Drilling area 84” x 144”
Spindle diameter 4”
Drilling capacity 3”
Morse taper in spindle nose No. 6MT
Spindle travel 18”
Column diameter 22”
Reach-center on spindle to center
of column, spindle vertical 106”
Distance center of horizontal spindle
to floor max. 163”; min. 79”
Distance - nose of vertical spindle
to floor max. 108”; min. 6”
Horizontal travel - column on runway 144”
Traverse rate on runway 80 IPM
Vertical travel of head on column 84”
Traverse rate on column 80 IPM
Traverse of head and rail on rail slide 36”
Traverse rate of rail 60 IPM
Swivel of head on trunnion 360º
Swivel of trunnion on rail 180º
Column swivel 360º
Height of runway 161/2”
Length of runway 18'
Width of runway 56”
9-Spindle speeds 35 to 600 RPM
9-Spindle feeds .0035 to .062 IPR
EQUIPPED WITH:
Hardened replaceable bedways
96” Extra column travel on bed
24” Extra vertical travel on column
Lifting ear on top of column cap. for portable use
Electric clamping of column swivel
Power clamping to all movements
Power rapid traverse
Rack and pinion drives, vertical & horizontal
Pendant control
10 H.P. 3/60/220-440 volt, 1740 RPM spindle drive
motor w/controls
Height over column cap.: 20' 6”
8' x 19" CARLTON Radial Drill: 8' x 19" CARLTON Radial Drill
Arm length: 8'
Diameter of column: 19"
Maximum spindle radius: 9' - 3/4"
Minimum spindle radius: 25 1/2"
Maximum distance spindle to base: 78"
Minimum distance spindle to base: 10"
Working surface of base: 48" x 101"
Height of base: 10"
Vertical travel of spindle in head: 20"
Spindle diameter: 4"
Taper in spindle: No. 6 M.T.
Traverse of arm on column: 48"
Traverse of head on arm: 83 1/4"
Infinitely variable spindle speeds (with 96 changes): 10 to 1250 RPM
18 Feeds: .004 to .125 IPR
Tap leads: 8-11 1/2-14-18
EQUIPPED WITH: T-slotted base
Power column clamping
Manual clamping of head
Hardened wear strip on arm
20 H.P. 230 volt DC motor with solid-state SCR control
MAXIMUM HEIGHT OVER COLUMN CAP: 11'8"
MAXIMUM HEIGHT OVER HEAD: 144"
6' x 17" CARLTON Radial Drill: 6' x 17" CARLTON Radial Drill
Length of arm: 6'
Diameter of column 17"
Face of column to center of spindle:
Maximum: 72"
Minimum: 13 1/4"
Maximum spindle radius: 85 3/4"
Maximum spindle to base: 72"
Minimum spindle to base: 14 1/2"
Working surface of base: 50" x 77"
Height of base: 10"
Vertical travel of spindle in head: 20"
Spindle diameter: 4"
Taper in spindle: No. 6 M.T.
Traverse of arm on column: 37 1/2"
Traverse head on arm: 58 1/4"
36 Spindle speeds: 15 to 1500 RPM
18 Feeds: .004 - .125 IPR
Tap leads: 8-11 1/2 - 14 - 18 T.P.I.
EQUIPPED WITH: T-slotted base with coolant pump
24" x 30" x 20"High, t-slotted box table
Power rapid traverse of head
Power clamping
20 H.P. 3/60/220-440 volt motor with controls
MAXIMUM HEIGHT OF HEAD: 140"
MAXIMUM HEIGHT OVER COLUMN CAP: 135"
5’ x 15” FRN-60/1600 NARDINI Radial Drill: 5' x 15" FRN-60/1600 NARDINI Radial Drill
Maximum spindle radius 63"
Column diameter 15"
Drilling capacity in solid steel 2 3/8"
Drilling capacity in cast iron 3 1/8"
Boring capacity in steel 3-15/16"
Boring capacity, cast iron 4 3/4"
Tapping capacity in steel 2
Tapping capacity, cast iron 2 3/4"
Spindle diameter 3-9/16"
Vertical spindle travel 13 3/4"
Taper in spindle No. 5 M.T.
Max. height spindle to base 62"
Min. height spindle to base 13 3/4"
Horizontal travel of head on arm 52 3/8"
Working surface of base 35 1/4" x 64"
Height of base 8 5/8"
Vertical travel of arm on column 34 1/2"
12 spindle speeds 29-1450 RPM
6 feeds .002-.017 IPR
EQUIPPED WITH:
T-slotted base
30" x 30" x 18"High T-slotted box table (slotted top and side
Coolant pump in base
Coolant splash guard
Power column clamping
(1) Drill holder
Motor amp meter
1 H.P. clamping motor
2 H.P. arm elevation motor
10 H.P. 3/60/200-230-460 volt spindle drive motor
Max. height above column: 119 1/2"
Max. height above headstock: 129 7/8"
Dimensions: 109 3/8"LR x 119 1/2"High
8’2” x 20 7/8” YAMAZEN YMZ Radial Drill Model TRE-2500D: 8’2” x 20 7/8” YAMAZEN YMZ Radial Drill Model TRE-2500D
Arm length 8’2”
Column diameter 20 7/8”
Taper in spindle No. 5 M.T.
Drilling capacity:
Solid steel 3 ¾”
Cast iron 4 ½”
Boring in steel 10 5/8”
Boring in cast iron 13 3/8”
Diameter of spindle 3 1/8”
Diameter of spindle quill 4 ½”
Spindle travel 19 5/8”
Max. distance, column to spindle center 99 3/16”
Min. distance, column to spindle center 16 1/8”
Horizontal travel of spindle head on arm 83 1/16”
Max. distance, spindle to base 68 7/8”
Min. distance, spindle to base 17 ¾”
Vertical travel of arm on column 33 15/32”
Size of base 47 ¼” x 137 ¾”
Height of base 11”
24 Spindle speeds 20-2000 RPM
18 Feeds .0015-.125 IPR
Tap leads 8,11 ½,14,18,27 T.P.I.
EQUIPPED WITH:
T-Slotted base
20”x 30”x 19” High T-Slotted box table
(3)T-Slots in top, (2) T-Slots in side
Power clamping
Work light
5 M.T. Quick-Change holder
Quick change tool w/drill chuck
5 H.P. arm elevation Motor
15 H.P. Spindle drive Motor
Max. height above column cap: 115 1/8”
Max. height above head: 135 1/8”
4' x 12" WMW HECKERT Radial Drill, Model BR40/2 x 1250: 4' x 12" WMW HECKERT Radial Drill, Model BR40/2 x 1250
Column diameter 12"
Maximum/Minimum distance from face of column 49.2"/11.8"
to centerline of spindle
Drilling capacity: Steel 1.77"
Cast iron 2.36"
Tapping capacity: Steel 1.5"
Cast iron 2"
Horizontal travel of head on arm 37-3/8"
Vertical travel of arm on column 29.3"
Vertical travel of spindle in head 14"
Minimum/Maximum distance, spindle to base 11"/54.3"
Size of base 36-1/4" F-B x 80-3/4" L-R
Height of base 8-3/4"
Spindle taper No.5 M.T. Morse
Infinitely variable spindle speeds in three geared 20-1,200 R.P.M
ranges for each speed of two speed motor
(6) Feeds .0025-.025 I.P.R.
Maximum height above spindle drive motor with 121-1/4"
the arm at the highest position on column
Maximum height above top of elevation motor 112"
Maximum height above column cap 96-1/2"
EQUIPPED WITH:
T-slotted base with coolant pump
27-1/2" x 27-1/2" x 19-3/4" High t-slotted (top and side) box table
Electro-mechanically actuated clamping of arm on column and head on arm
Motorized raising/lowering of arm on column
Changeover switch for drilling or tapping operations
Hardened steel ways on arm
Feed overload clutch
Mechanical tool ejector
1/8"-3/4" Capacity JACOBS drill chuck
1 H.P. clamping motor
2 H.P. arm elevation motor
3.5-5.9 H.P. 3/60/440 volt two-speed spindle drive motor and electrical controls
IKEDA Radial Drill, Model RM-1300: IKEDA Radial Drill, Model RM-1300
Capacity #5 M.T. Morse taper
Arm length 4’
Column diameter 13”
Spindle travel 12”
Max. distance column face to spindle 10 ¾” min, 54 ½” max.
Max. distance spindle to base 15 7/14” min, 56 ¾” max.
12 Spindle speeds from 30 to 1440 RPM
4 Feeds from .004 to .021 IPR
EQUIPPED WITH:
T-Slotted base
Power clamping & power elevation to arm
Coolant pump in the base & piping
5 HP Spindle drive motor, 220/440/3/60
Tilting box table: 20”x20” top, 20”x12” side
12” Heavy duty swivel vise
Tapping reverse
57”x 36” machined surface of base
3’ x 9 ½” JET Radial Drill, Model JRD-939: 3’ x 9 ½” JET Radial Drill, Model JRD-939
Column diameter 9 ½”
Max. distance, spindle to column 39 3/8”
Min. distance, spindle to column 11 ¾”
Taper in spindle No.4 M.T.
Drilling capacity:
Steel 1 9/16”
Cast Iron 2 1/16”
Tapping capacity:
Steel 1”
Cast Iron 1 ½”
Boring capacity:
Steel 3 3/8”
Cast Iron 4 ¾”
Horizontal travel of head on arm 27”
Max. distance, spindle to base 45”
Min. distance, spindle to base 13”
Vertical traverse of arm 30 ¾”
Spindle travel 11”
Working surface of base 17 ¾” x 31 ½”
16 Spindle speeds 32-2500 RPM
8 Feeds 0.0031-0.0394 IPR
EQUIPPED WITH:
T-Slotted base
17 ¾” x 23 ¾” x 17 ½” High T-Slotted box table
with 6” riser block
Electric column clamping
Quick change tool holder
Spindle reversing switch
Coolant system
Work light
1 H.P. arm elevation motor
3 H.P. 3/60/230-460 Volt Motor w/controls
BURGMASTER Six Spindle Turret Drilling and Tapping Machine, Model2DCP: BURGMASTER Six Spindle Turret Drilling and Tapping Machine, Model2DCP
Drilling capacity, mild steel 3/4"
Tapping capacity, mild steel 3/4" N.F.
Turret travel 8"
Table size 24" x 40"
Throat depth 11-1/2"
(12) Preselective spindle speeds, three ranges 225-3,000 R.P.M.
Carriage travel 15"
Work height, spindle nose to table, head up 9"
carriage down
Work height, spindle nose to table, head up 24"
carriage up
Feed, infinitely variable and preselective for each 1-45 I.P.M.
spindle
Rapid traverse, pre-selective in length for each 195 I.P.M.
spindle
Depth control, pre-selective in length for each plus or minus .002"
spindle
EQUIPPED WITH:
Electric feed system: Manual by fast or or slow Jog Control,
Semi-Automatic, orFully Automatic
Spindle Cycle Selector: allows complete automatic cycling. Each of the six spindles
can be programmed individually by the flick of the assigned thumbwheel. Rapid
approach points are adjustable through a cam setting. Automatic retraction at the
end of the machining operation (drilling, reaming, dwell for counterboring,
and boring). The turret then indexes bringing the tool into the new position. The
slide rapid traverses down to the new feed engagement point andthe new preselected machining operation occurs.
Spindle Function Selector is also programmed by thumbwheel. It provides the Cycle
Stop mode-that is, stopping the automatic cycle operation on a given spindle at the
conclusion of the spindle's preassigned cycle and also preselects the motor speed.
Key lock selector switch for Indexer Auto Enable
Rheastat for Reciprocating Feed (peck drill)
(6) 1/32"-1/2" Capacity ALBRECHT keyless drill chucks
External coolant pump and tank
2-1 H.P. 3/60/220-440 volt two-speed drive motor coupled to a two step belt drive
and electrical controls
5’ x 15” AMERICAN “HOLE-WIZARD” Radial Drill: 5’ x 15” AMERICAN “HOLE-WIZARD” Radial Drill
Arm length 5’
Column diameter 15”
Taper in spindle No.5 M.T.
Max. distance, spindle to base 66”
Min. distance, spindle to base 6”
Spindle travel 18”
32 Spindle speeds 15-1200 RPM
16 Feeds .003-.125 IPR
Tap leads 8-11 ½-14-18 T.P.I.
Horizontal travel of head on arm 46 ¾”
Vertical travel of arm on column 42”
Height of base 9”
Size of Rt. Angle base 42”W x 61”L
EQUIPPED WITH:
T-Slotted right angle base
36”x36”x20 ½” High, T-Slotted box table
28”x28”x20 3/8” High, T-Slotted box table
Power clamping
Coolant pump in base
Motorized elevation
10 HP 3/60/220-440 Volt Motor and controls
Height over Column cap: 128”
USED AMADA MODEL H-2000, LARGE CAPACITY HORIZONTAL BANDSAW: USED AMADA MODEL H-2000, LARGE CAPACITY HORIZONTAL BANDSAW
MAX, CUTTING CAPACITY: 2000 X 2000MM (78.74" SQUARE)
SIDE CUTTING CAPACITY: 2000 X 400MM (78.4 X 14.74")
BLADE SIZE: 120MM WIDE X 1.6MM THICK, X 1700MMM LONG (4.72" X .06" X 669")
TABLE SIZE: 2000 X 5000 MM (78.74 X 196.85")
TABLE TRAVEL: 4500MM (177.165")
TABLE FEED RANGE: 30-2000 MM/MINUTE
(1.18 X 78.74" /MINUTE)
MAX. WORKTABLE WEIGHT CAP: 100 TON
SAW BLADE DRIVE MOTOR: 15 HP
HYDRAULIC DRIVE MOTOR: 7.5 HP
COOLANT MOTOR: 0.5 HP
APPROX. SIZE: 6840 H X 8370 W X 11100 L MM
(22.44' X 27.46' X 36.42')
ESTIMATED FLOOR SPACE REQUIRED: 11000 X 12700MM (36.08' X 41.67')
AMADA MODEL HFA400S AUTOMATIC HORIZONTAL BAND SAW: AMADA MODEL HFA400S AUTOMATIC HORIZONTAL BAND SAW
Capacity: 16" x 16" (Rectangular)
16.14" (Rounds)
Load Capacity: 5733 Lbs
Blade Length: 16'5"
Blade Width/Gauge: 1-1/2" x .05"
Blade Speeds (Variable): 50 - 393 FPM
Feed Length (Variable): .394" - 99.999"
Maximum Number of Pieces to be Cut: 999 per Station
Table Height from Floor: 25-1/2"
EQUIPPED WITH:
99 Station Micro-Processor Back Gauge
Blade Breakage and Slip Detection
Automatic Bar Feed
Hydraulic Clamps
Variable Feed and Speed Control
Automatic Hydraulic Screw Type Chip Conveyor
Coolant System
1/4 HP AC Coolant Pump Motor
5 HP AC Main Drive Motor
2 HP AC Hydraulic Pump Motor
Electrical Controls
WF Wells, Twin Post Band Saw, 15" x 16", No. F15, Hyd. Down Feed: WF Wells, Twin Post Band Saw, 15" x 16", No. F15, Hyd. Down Feed
SPECIFICATIONS:
Capacity: 15" X 16"
Weight Capacity: 12,000 LBS.
Blade Size: 1-1/4" X .042" X 14'5"
Blade Speed (variable): 65 TO 390 FPM
Stroke Length: 1/8" TO 24", or 3 strokes to 72"
Sawing Force: 0 TO 300 Lbs.
Saw Head Cycle Time, Raise: 17" in 4 sec.
SAW Head Cycle Time, Lower: 17" in 4 sec.
Hydraulic Pump Motor: 2 hp A.C.
Blade Drive Motor: 5 hp
EQUIPPED WITH:
Automatic Cycle
((2 Hydraulic Vise))
((2 Hydraulic Hold Down Vises (For Bundling)))
Hydraulic Rise and Fall
Hydraulic Blade Tensioning
Coolant Pump
10' Infeed Table
Chip Pan
Control Console
21.7" KALTENBACH Non-Ferrous Automatic Circular Cold Saw, RKL550 AX: 21.7" KALTENBACH Non-Ferrous Automatic Circular Cold Saw, Model RKL550 AX
Cutting capacity at 90 degrees:
Rounds 6.5"
Squares 6.1"
Profiles 15.3" x 1.2"
Blade diameters 17.7", 19.7", 21.7"
Cutting speed with 21.7" diameter blade 16,320 S.F.M.
Blade feed rate, infinitely variable 0-86.6 I.P.M.
Rapid return of saw blade 236.2 I.P.M.
Saw blade type Carbide metal
Cut-off lengths from .39" to 78.7"
EQUIPPED WITH:
Model S5 SIEMENS PLC control of cutting lengths and quantities
Ball screw driven length stop nut
Carriage driven by chain and motor
Fine adjustment of cutting length by hand wheel and digital display
Counter for preselecting the required number of cut-offs
Infinitely variable and hydraulically actuated upward saw blade feed with rapid return
Contact free return stroke (automatic enlargement of cutting gap)
Vertical vise used to clamp work piece on both sides of the saw blade
Short stroke vise with hand crank for preadjustment
Sound proofed cabin around the complete machine area
Infeed and outfeed tables
Chip exhaust system
Accu-Lube spraymist coolant
Miscellaneous spare parts including rebuilt drive motor
Approximately (20) miscellaneous saw blades
8 H.P. direct drive motor and electrical controls
10' Semi-Auto Hendricks Non-Ferrous Panel Saw: This is a Hendricks panel saw completely rebuilt
14" blade
cut 10 foot semi-auto
set up for top and bottom evacuation systems
MARVEL All Mechanical, Universal Vertical Band Saw, Model No. 8: MARVEL All Mechanical, Universal Vertical Band Saw, Model No. 8
Capacity: Nominal 18" x 18"
Maximum 18" x 22-1/2"
blade at 45 degrees nominal 18" x 12-1/2"
blade at 45 degrees maximum 18" x 14"
Number of t-slots in table (size) 4 (3/4")
Table working surface 33" x 24-1/4"
Table height 32-1/2"
Blade length 14' 8"
Blade width/gauge 3/4" x .032
Maximum vise opening 21"
Height of vise jaws 6"
(6) Blade speeds 40 to 200 F.P.M.
EQUIPPED WITH:
Manually operated tilt column and blade up to 45 degrees left and right of vertical for
miter cutting
Built-in tilt protractor for setting column at desired angle
T-slotted work table with quick-acting vise
Stops to limit both forward and return travel of the column and blade
Automatic blade tensioning
Self-contained coolant system with pan
1.5-.75 H.P. 3/60/230 volt, 850/1,765 R.P.M. two speed drive motor with push button electrical controls
18”x 20” No. 8 MARVEL Hi-Column Tilt Frame Vertical Band Saw, Model 8/: 18”x 20” No. 8 MARVEL Hi-Column Tilt Frame Vertical Band Saw, Model 8/MGI
Capacity:
Nominal 18” x 23 ½”
Maximum 18” x 28”
Blade at 45° Nominal 18” x 16 ½”
Blade at 45° Maximum 18” x 18”
Table working surface 33” x 24 ¼”
Table height 32 ½”
Tee slots-No. and size 4- ¾”
Maximum vise opening 21”
Height of vise jaws 6”
6 Blade speeds 40-200 FPM
EQUIPPED WITH:
(1) Work vise
Coolant pan
1 ½ / ¾ H.P. 3/60/230 volt main drive motor with controls
1997 Anca MG-7 CNC Tool & Cutter Grinder: 1997 Anca MG-7 CNC Tool & Cutter Grinder
7 Axis CNC Tool & Cutter Grinder
Anca Control
Pop Up Steady
Probe
Auto Loader
Hard Drive
Floppy
Travels 13" x 8" x 9"
C-270 Deg
B-180 Deg
24” x 28” x 72” THOMPSON Hydraulic surface grinder, Model C: 24” x 28” x 72” THOMPSON Hydraulic surface grinder, Model C
Capacity 24” x 72”chuck size
no incremental downfeed
Max. height above table with new wheel 28”
Wheel size 20”x6”x12”
Table speed range 10-100 FPM
Hydraulic cross feed 1/32” to half wheel width
EQUIPPED WITH:
24” x 72” Electromagnetic chuck with
neutrofier control
12” extra column height
Wheel dresser
(1) wheel mount
Automatic lubrication
Rapid traverse to wheel head
Splash guards
Coolant system
Hydraulic power unit
15 H.P. 3/60/220-440 volt spindle drive
motor with controls
31.5"x39.4"x144" CAMUT Hi-column hyd surface grinder, Model TR-2-3000M: 31.5" x 39.4" x 144" CAMUT Hi-column hydraulic
surface grinder with automatic downfeed, Model TR-
2-3000M
Table working surface 27.56" x 148"
Maximum table travel 145.7"
Maximum height table to new 22" dia. wheel 39.37"
Maximum height table to new 15" dia. wheel 42.91"
Wheel cross travel 31.5"
Maximum wheel size 22" dia. x 6"W x 8" hole
Variable table speeds 3.94-98 FPM
Automatic cross feed rates .12" to 3"
Automatic downfeed rates (10 steps) .0002"-.002"
Wheel speed 1152 RPM
EQUIPPED WITH:
Automatic downfeed of wheel (10 steps)
Full hydraulic operation
Automatic vertical downfeed may be programmed
with wheel cross reversal or table reversal
(single or double)
(3) 27 1/2" x 39 5/8" EMC electromagnetic chucks
in series with variable control
Head mounted hydraulic wheel dressing with 12"
stroke and variable control
Wheel arbor balancing stand
Rapid traverse to wheelhead
Marposs electronic sizing (vertical movement)
Auto. central lubrication system
Hardened Vee-type bed ways
(4) wheel mounts with grinding wheels
Way covers
EXL200 Casven coolant separator (1200 liter cap.)
15 H.P. Vichers dual delivery pump system
50 H.P. wheel drive motor
12" x 24" KENT Hydraulic Surface Grinder, Model KGS-63SD1: 12" x 24" KENT Hydraulic Surface Grinder, Model KGS-63SD1
Capacity:
Overall table working area (width x length) 11.81" x 25.59"
Longitudinal table travel 27.95"
Cross table travel 13.39"
Maximum table load (with chuck) 550 Lbs.
Maximum/Minimum distance between working table 21.25"/4.72"
and spindle center
Table Cross Feed:
Longitudinal table speed 8 to 100 F.P.M.
Cross feed hand wheel is graduated in increments of .0001"
Automatic cross feed per stroke of table .02" to .4"
Grinding Wheel:
Standard wheel dimensions 14" diameter x 1.5" maximum
Width x 5" bore
Spindle speed 1,740 R.P.M.
Downfeed:
Automatic down feed increment 0.0001" to .004"
Downfeed hand wheel is graduated in increments of .0001"
Downfeed travel per revolution of hand wheel .02"
EQUIPPED WITH:
Hydraulically actuated longitudinal feed
Electromechanically actuated cross feed
Automatic incremental downfeed of grinding wheel head driven by stepping motor
Programmable logic controller (PLC) of all machine functions including: "Rough
Downfeed" increment and number of passes, "Fine Downfeed" increment and
number of passes, "Sparkout" times, "Downfeed Mode" for control of incremental
downfeed with table at right end of stroke, left end of stroke, or both left and right
end of stroke, "Wheel head Elevation & Position" for control of elevation increment
at completion of grinding job, "Jog" increment to allow the operator to select three
different jog rates of the grinding wheel head, and "Reset" to set the current position
of the grinding wheel as 0 point The PLC has a LED display to show the position
of the grinding wheel in relation to the starting point.
Selector switch for surface or plunge grinding modes of operation
Selector switch for automatic incremental downfeed, downward jogging, or power
rapid elevation of grinding wheel head
12" x 23-5/8" Fine division electromagntetic chuck with console mounted controls
including: variable magnetic strength, magnetization/demagnetization mode
selector, and voltage gauge meter
Over-the-wheel parallel dresser
External hydraulic pump and tank
External coolant pump and tank with paper band filtration
5 H.P. 3/60/575 volt spindle drive motor
BROWN & SHARPE Universal Tool & Grinding Machine, Model #13: BROWN & SHARPE Universal Tool & Grinding Machine,
Model #13, Projectordress Added 1992
Capacity:
Grinds work up to 8" diameter
Grinds length 14"
Distance between headstock and footstock centers
24"
Maximum distance between tailstocks 31"
Maximum automatic table travel 22"
Maximum length of work which can be ground 15"
cylindrically with wheel spindle parallel to
table
ways
Minimum/Maximum distance centerline of work to
2.25"/12.5"
center of wheel spindle
Minimum/Maximum distance center of wheel spindle
3.75" / 12-1/8"
to top of table
Wheelhead:
Grinding wheel size 7" diameter x 1/2" wide x 1-
1/4"bore
(3) Grinding wheel speeds 2,730 & 3,600 & 5,150
R.P.M.
Wheelhead travel 8-3/8"
Wheelhead swivels, left and right 110 degrees
Vertical adjustment 8-3/8"
Swivel Table:
Working surface 6-1/8" x 44-1/8"
Angular settings to left and right 90 degrees
Fine screw adjustment for setting tapers up to 3"
per foot
Table travel 22"
Table travel per revolution of handwheel 1/4"
slow, 6-1/4" fast
Headstock:
Swivels left and right 100 degrees
(4) Spindle speeds 128 to 540 R.P.M.
Spindle taper #7 BROWN & SHARPE
EQUIPPED WITH:
"Projectordress" optical dresser with "Factsor"
digital display (Used for dressing optical
forms into the grinding wheel)
Four-jaw chuck
Three-point steady rest
Universal table, workhead, and wheelhead
Double ended wheel spindle
Dual live/dead headstock spindle
Fine cross feed knob (graduated to 0.0001" work
diameter)
Vertical handwheel graduated to read to .0005"
Anti-friction bearings for wheelhead spindle
1/6 H.P. workhead motor
1 H.P. 3/60/220-440 volt wheelhead motor and
electrical controls
10" x 32" CLAUSING JAKOBSEN Hydraulic Surface Grinder, Model SJ-1032: 10" x 32" CLAUSING JAKOBSEN Hydraulic Surface Grinder with Automatic
Incremental Downfeed, Model SJ-1032
Work capacity 11.81" x 31.5"
Longitudinal travel of table 35.43"
Cross travel of table 12.2"
Maximum height, spindle center to table 21.65"
Working surface of table 9.84" x 31.5"
Table longitudinal feed rate, infinitely variable 7.9 to 119 F.P.M.
Automatic cross feed at saddle reversal, .079" to 1.19"
infinitely variable
Automatic vertical feed range, infinitely variable .0001" to .0099"
Rapid cross feed rate 240 I.P.M.
Rapid vertical feed rate 12 I.P.M.
Vertical feed hand wheel reads to .0001"
One revolution of vertical feed hand wheel equals .01"
Fine cross feed knob reads to .0001"
Maximum table load 660 Lbs.
Standard wheel size 14" diameter x 1.57" wide
Grinding wheel speed 1,700 R.P.M.
EQUIPPED WITH:
Hydraulically actuated longitudinal feed
Rack and pinion longitudinal table drive during manual operation
Hydraulically actuated continuous or intermittent cross feed
Fine adjustment cross feed knob graduated to .0001"
Double saddle locking device
Automatic incremental down feed actuated through stepping motor at each reversal of
the saddle for plunge or slot grinding or at each reversal of table for surface
grinding. Down feed travel is digitally displayed counting back to zero.
Digital display of every .01" movement of down feed hand wheel in both directions. This
system works independently of the automatic down feed.
1/2 H.P. motorized rapid vertical feed up and down of grinding wheel head
Hydraulically actuated wheel dresser mounted on top to the wheel spindle permitting
straight line dressing of wheels up to 1" wide
10" x 32" O.S WALKER "Interlock" electromagnetic chuck with control (The
Interlock chuck is designed for very low heat emission and thus is used for very
high precision grinding).
Operation and spare parts manuals
(1) Wheel mount
Automatic lubrication system
External coolant pump and tank
3 H.P. external hydraulic pump and tank
5.5 H.P. spindle drive motor and electrical controls
20" x 60" KIKINDA Hydraulic Surface Grinder: 20" x 60" KIKINDA Hydraulic Surface Grinder With Programmable
Incremental Down-feed, Model PRB-500/1500
Width x length ground (nominal capacity) 20" x 60"
Maximum table travel 63"
Maximum cross feed travel 22"
Maximum wheel head height adjustment 25"
Hydraulic table feeds up to 83 F.P.M.
Auto cross-feed increments 0 to 1" per table stroke
Wheel size 16" diameter x 2" wide x 5" bore
Auto incremental down-feed, programmable in 0.0001" to .001"
increments from
EQUIPPED WITH:
Hydraulic table traverse
Automatic cross feed
Programmable automatic incremental down-feed
Automatic wheel retraction and table park at completion of grind cycle
Digital display on control console for setting amount of stock to be removed per
grinding pass
Column mounted digital readout for display of wheel head position
Over-the-wheel dresser
20" x 60" Electromagnetic chuck with Neutrofier control
Coolant system with paper filtration
11 H.P. spindle drive motor
16" x 36" Brown & Sharpe 3-axes CNC Surface Grinder: 16” x 36” BROWN & SHARPE Hi-tech 3-axes CNC
controlled Surface, profile and creep feed grinder
cnc grinder
Minimum table stroke .4”
Maximum grinding stoke 40”
Nominal grinding length 36”
Maximum grinding width 17”
Nominal grinding width 16”
Table size 16” x 36”
Max. work height Under 14” Dia. wheel 18”
Max. work height Under 16” Dia. wheel 16”
Wheel size 16” Dia. x 3” Width
Infinitely variable table speed range .4 to 100
IPM
Infinitely variable wheel speeds 100 to 3000 RPM
Max. reciprocation rate of table 200 S.P.M.
Continuous feed rate 0 to 225 IPM
Incremental feed, minimum .000010”
Incremental feed, maximum 1”
Vertical feed of wheel head 19 ¼”
Rapid traverse rate of wheel head 0 to 40 IPM
EQUIPPED WITH:
Ball screw drives for cross and wheel slides
14”x32” electromagnetic chuck w/ control
Dresser
Coolant filtration System
Coolant Splash enclosure
Wheel mount
Automatic lubrication
Integral cartridge type Spindle drive
15 H.P. DC Variable speed Spindle drive
Allen Bradley Series 9 CNC control with CRT, port
Note: machine has an x axis table movement needs
adjusting or work
23" FAVRETTO Column-type horiz. spindle rotary surface grinder, RT 60: 23" FAVRETTO Column-type horizontal spindle rotary surface grinder, RT 60
Diameter of rotating table 23 5/8"
Maximum swing inside of water guards 28"
Maximum wheel head traverse 9 1/2"
Maximum/minimum distance from table to wheel center 16 1/2"/7"
Angle of head swivel for conical grinding 10° either side of zero
Grinding wheel size 14" dia. x 1 1/4" face x 5" bore
Grinding wheel speed 1,400 RPM
Grinding wheel continuous cross feed,
infinitely variable 8 to 236 I.P.M.
Grinding wheel vertical feed .0002" to .00157"
Table speeds, infinitely variable to 120 RPM
EQUIPPED WITH:
Vertical column type construction
23 5/8" diameter electromagnetic chuck with RELIANCE variable speed controller and ELECTROMATIC PRODUCTS CO. Neutrol rectifier
Electro-hydraulically actuated automatic micrometer down-feed of grinding wheel head at each cross feed reversal
Electro-mechanically actuated power rapid traverse of grinding wheel head vertical travel
Hydraulically actuated power rapid cross feed of wheel head assembly
Over-the-wheel diamond dresser with micrometer adjustment
BIJUR lubrication system
Self-contained coolant system with 1/4 H.P. drive motor
Self-contained hydraulic system with 1 1/2 H.P. drive motor
1 H.P. vertical rapid traverse motor
2 H.P. table drive motor
5 H.P. 3/60/220-440 volt spindle drive motor and electrical controls
No. 3 MOORE Precision Jig Grinder: No. 3 MOORE Precision Jig Grinder
Table size: 11" x 24"
Range:
table movement 11" x 18"
table top to wheel collet, minimum 2"
table top to wheel collet, maximum 18"
Spindle to column ways 10"
Spindle to column below ways 13 1/2"
Infinitely variable spindle speeds 40-250 RPM
Infinitely variable spindle feeds 2-120 SPM
Grinding capacity
grinding wheels 3/16"-5"
diamond mandrels 1/64"-3/16"
Main spindle slide travel 3 5/8"
Angular adjustment of spindle
either way 1 1/2°
included angle 3°
Radial offset of grinding spindle
from center to 1 1/8" off center by rough adjustment while running
.0001" adjusted for distance of .100" anywhere in the 1 1/8" range
EQUIPPED WITH:
Hardened, ground and lapped steel ways (no gibs)
Hardened, ground and lapped lead screws
(1) 40,000 RPM jig grinding head
BIJUR spraymist coolant
Way covers
½ H.P. variable D.C. motor with rectifier
MOORE Precision Jig Grinder: MOORE Precision Jig Grinder, Mdl. G-18
Table size 11" x 24"
Range, table movement 11" x 18"
table top to wheel collet, minimum 2"
table top to wheel collet, maximum 18"
Spindle to column ways 10"
Spindle to column below ways 13 1/2"
Infinitely variable spindle speeds 25-225 RPM
Infinitely variable spindle feeds 2-120 SPM
Spindle feed adjustable from 0.100" to 3 5/8"
Grinding wheel speeds 6,000-175,000 RPM
Grinding capacity, grinding wheels 1/64"-3 1/2"
Angular adjustment of spindle either way 1-1/2°
included angle 3°
Radial offset of grinding spindle
from center to 1 1/8" off center by rough adjustment while running
.0001" adjusted for distance of .100" anywhere in the 1 1/8" range
EQUIPPED WITH:
Hardened, ground and lapped steel ways (no gibs)
Hardened, ground, and lapped nitralloy leadscrews
Leadscrews and nuts that are fully immersed and operated in a bath of oil
(2) MOORE grinding heads
Misc. grinding wheels and accessories
42" MATTISON Hi-Column Vertical Rotary Surface Grinder, Model 24-42: 42" MATTISON Hi-Column Vertical Rotary Surface Grinder, Model 24-42
Completely rebuilt 1997 by Dial Industries
Table Diameter 42"
Max. Swing 56"
Max. Work Height 30"
5 Table Speeds 8 to 32 RPM
Magnetic chuck life 5/8"
Continuous feed range .005 to .165 IPM
Feed wheel graduated in steps .0001"
Wheel Speed 700 RPM
Equipped with:
42" Dia. magnetic chuck (new 1997)
Tilt spindle feature
Automatic cycle
22" Dia. segmental chuck with quantity of new segments
Motorized rapid traverse to wheel
Newall DPG 1-axes D.R.O.
Barnes Magnetic filtration system
Neutrofier II solid state chuck control
Motor amp meter
Lub + air fault system
Work light
Trabon auto. lub. system
100 H.P. wheel drive with cooling fan + filter
Max. height: 11'6"
Dimensions: Machine only ( 109"L x 62"W x 126" High) with head down
10” x 18”cc JONES & SHIPMAN universal cylindrical grinder, Model 1311: 10” x 18”cc JONES & SHIPMAN universal cylindrical grinder, Model 1311
Maximum diameter ground with new wheel 10”
Maximum grinding length between centers 18”
Maximum workpiece weight between centers 220 lbs.
Table traverse per handwheel revolution 5”
Table traverse fine feed graduations 0.50”
Table traverse steplessly variable per minute 0.0005”
Minimum table stroke under hydraulic control 0.040”
Table swivel adjustment-included angle clockwise/
included angle anti-clockwise 19°/20°
Infeed rate at table reversal, reduction in work diameter 0.0002”-0.0012”
Wheelhead feed handwheel-rapid/standard feed 0.250”/0.50”
per revolution, reduction in work diameter
(6) workhead speeds 40-320 RPM
Workhead swivel, clockwise/counter-clockwise 15°/90°
Workhead and tailstock spindle center taper #3 Morse
Standard grinding wheel (Type EIU wheelhead) 14” diameter x 1” wide x 5”
bore
(2) wheelhead speeds 2,000 & 2,680 RPM
Wheelhead swivel adjustment each side or normal
position 180°
Cross traverse of wheelhead 8-1/16”
EQUIPPED WITH:
Manually operated or hydraulically actuated table traverse
Manually operated, automatic intermittent (at table reversal) and automatic continuous (plunge grinding) modes of wheelhead infeed
Rapid wheelhead advance and retraction
Swing-around internal grinding attachment with spindle
¾ H.P. 3/60/220-440 volt motorized workhead with 6” diameter 4-jaw chuck, 6 ¼” diameter magnetic chuck, and combination live/dead center
Tailstock with assorted full and half centers
(1) 5/16”-3” diameter capacity 3-point plain-type steady rest
(1) 5/16”-3” diameter capacity 2-point open-type steady rest
Table mounted diamond holder for dressing wheel
Self-contained hydraulic system with 1 H.P. motor
External coolant pump and tank
Manually operated 1-shot lubrication system
5.5 H.P. 3/60/220-440 volt wheelhead motor and electrical controls
68" X 320" MATTISON PLANER TYPE HORIZONTAL GRINDER: 68" X 320" MATTISON PLANER TYPE HORIZONTAL SPINDLE
RECIPROCATING TABLE HYDRAULIC SURFACE GRINDER
MANUFACTURED 1958. . . REBUILT AND MODERNIZED BY
CROSS & TRECKER IN 1988.
WORK TABLE WORKING SURFACE: 68" X 300"
WORK TABLE AS SET UP W/CHUCKS: 72" X 167"
TABLE TRAVEL: 320"
DISTANCE BETWEEN HOUSINGS: 84"
MAXIMUM HEIGHT UNDER WHEEL: 60"
GRINDING WHEEL CAPACITY: 20" X 6"
TABLE LOAD CAPACITY: 55,000 LBS.
TABLE SPEEDS: 0-100 FPM INF. VAR.
WHEELHEAD TRANSVERSE SPEED: 0-30 FPM
WHEELHEAD MOTOR: 30 HP
EQUIPPED WITH:
(4) 24" X 72" ELECTRO-MAGNETIC CHUCKS
CROSS RAIL MOUNTED WHEELHEAD
BALLSCREWS - CROSS/GRIND FEED
WHEEL GUARD DRESSER
POWER CLAMPING
ALLEN BRADLEY CONTROLS W/AIR CONDITIONING
HYDRAULIC TABLE DRIVE
AC SERVO DRIVES
PAPER MEDIA FILTRATION
HARD INSERTS ON CROSS RAIL
FULL PENDANT CONTROL
WORK PLATFORM & BENCHES
ELECTRICAL DOCUMENTATION
12" X 36" GALLMEYER & LIVINGSTON MODEL 550 HYDRAULIC SURFACE GRINDER: USED 12" X 36" GALLMEYER & LIVINGSTON MODEL 550
HYDRAULIC SURFACE GRINDER
CAPACITY: 12" WIDTH
18" HEIGHT
36" LENGTH
TABLE TRAVEL, LONGITUDINAL: 47-1/2"
TABLE TRAVEL, TRANSVERSE: 13-3/4"
WORKING SURFACE OF TABLE: 12" X 36"
VERTICAL MOVEMENT OF WHEELHEAD: 19"
STANDARD WHEEL SIZE: 14" X 1-1/2" X 5"
MAX. DISTANCE WHEEL TO TABLE WITH NEW WHEEL: 18"
SPINDLE SPEEDS: 1750 & 2100 RPM
MOTORS: 7-1/2 HP SPINDLE
3 HP HYDRAULIC
EQUIPPED WITH:
POWER INCREMENTAL DOWNFEED
POWER WHEELHEAD ELEVATION
12" X 36" ELECTROMATIC CHUCK W/CONTROLS
COOLANT SYSTEM
PUSH BUTTON CONTROL STATION
WHEEL DRESSER
SPLASH GUARDS
AUTOMATIC LUBRICATION
12´´ X 72´´ CINCINNATI UNIVERSAL CYLINDRICAL GRINDER: 12´´ X 72´´ CINCINNATI UNIVERSAL CYLINDRICAL GRINDER
SWING OVER BED ...................... 12-1/2´´
DISTANCE BETWEEN CENTERS ............ 72´´
HYDRAULIC TABLE TRAVEL .............. 3 TO 220 IPM
AUTOMATIC INFEED .................... .002´´ TO .0125´´
WORKHEAD SPEEDS (VARIABLE) .......... 55 TO 500 RPM
GRINDING WHEEL ...................... 14´´ X 1-1/2´´
DROP DOWN ID ATTACHMENT
TABLE MOUNTED DRESSER
5´´ STEADY REST
BACKREST
COOLANT
3 HORSEPOWER WHEELHEAD MOTOR
1-1/2 HORSEPOWER HYDRAULIC MOTOR
1 HORSEPOWER VARIABLE SPEED WORKHEAD MOTOR
3/4 HORSEPOWER ID WHEELHEAD MOTOR
14´´ X 36´´ CINCINNATI PLAIN CYLINDRICAL GRINDER: 14´´ X 36´´ CINCINNATI PLAIN CYLINDRICAL GRINDER
SWING OVER TABLE ................... 14-1/4´´
MAXIMUM DISTANCE BETWEEN CENTERS ... 37´´
WORKHEAD SPEEDS .................... 40 TO 160 RPM
TABLE FEEDS ........................ (24) 3-1/2 to 120 IPM
AUTO INFEED AT TABLE REVERSAL
STANDARD GRINDING WHEEL ............ 30´´ DIAMETER X 3´´ FACE
RAPID TRAVERSE OF WORK HEAD ........ 16 IPR
COOLANT
20 HORSEPOWER MAIN MOTOR
1 HORSEPOWER/VARIABLE SPEED WORKHEAD MOTOR
14´´ X 48´´ CINCINNATI PLAIN CYLINDRICAL GRINDER: 14´´ X 48´´ CINCINNATI PLAIN CYLINDRICAL GRINDER
MACHINE EQUIPPED WITH ELECTRONIC COMMAND (BALL SCREW) INFEED
SWING OVER BED .......................... 14-1/2´´
DISTANCE BETWEEN CENTERS ................ 48´´
HYDRAULIC TABLE TRAVEL ............. 3 TO 250 IPM
AUTOMATIC INFEED OF WHEEL HEAD 0.00075 - 0.150 ipm
DIAMETER OF GRINDING WHEEL .............. 30´´
MAXIMUM WIDTH OF GRINDING WHEEL ......... 4´´
PLUNGE GRINDING
WORKHEAD JOG/HEADSWIVEL TABLE WITH DIAL INDICATOR
AUTOMATIC WHEEL BALANCING
DRESSER MOUNTED ON TAILSTOCKCOOLANT WITH PAPER FILTER SYSTEM
20 HORSEPOWER WHEELHEAD MOTOR
3 HORSEPOWER HYDRAULIC DRIVE MOTOR
1 HORSEPOWER WORKHEAD MOTOR
10´´ X 96´´ LANDIS PLAIN CYLINDRICAL GRINDER: 10´´ X 96´´ LANDIS PLAIN CYLINDRICAL GRINDER
SWING OVER BED .......................... 10-3/4´´
DISTANCE BETWEEN CENTERS ................ 96´´
HYDRAULIC TABLE TRAVERSE ................ 3 TO 130 IPM
AUTOMATIC INFEED AT TABLE REVERSAL ...... .00025´´ TO .003´´
WORK HEAD SPEEDS ........................ 54, 76, 107, 150 RPM
DIAMETER OF GRINDING WHEEL .............. 30´´
WIDTH OF GRINDING WHEEL ................. 3´´
GRINDING WHEEL SPEEDS ................... 810 & 995 RPM
TAPER IN HEADSTOCK AND FOOT STOCK ....... #14 JARNO
COOLANT
15 HORSEPOWER WHEEL HEAD MOTOR
3 HORSEPOWER HYDRAULIC MOTOR
1 HORSEPOWER WORK HEAD MOTOR
12" X 40" TOYODA UNIVERSAL CYLINDRICAL GRINDER: 12´´ X 40´´ TOYODA UNIVERSAL CYLINDRICAL GRINDER
TYPE .............................. GUP 30 X 100
SWING OVER BED .................... 12´´
MAXIMUM DISTANCE BETWEEN CENTER ... 40´´
WHEEL SPEEDS ...................... 1610 RPM
WORK HEAD SPEEDS .................. 0 TO 300 RPM (VARIABLE)
GRINDING HEAD SWIVEL .............. 180 DEGREES
WORK HEAD SWIVELS ................. 180 DEGREES
HYDRAULIC TABLE TRAVEL ............ YES
AUTO INFEED AT TABLE REVERSAL ..... YES
PLUNGE GRINDING ................... YES
DROP DOWN ID ATTACHMENT ........... YES
WHEEL HEAD MOTOR .................. 5 HORSEPOWER
HYDRAULIC MOTOR ................... 2 HORSEPOWER
DROP DOWN INTERNAL GRINDING MOTOR . 1 HORSEPOWER
WORK HEAD MOTOR ................... 1/2 HORSEPOWER
12´´ X 36´´ CINCINNATI UNIVERSAL CYLINDRICAL GRINDER: 12´´ X 36´´ CINCINNATI UNIVERSAL CYLINDRICAL GRINDER
SWING OVER BED ....................... 12-1/2´´
MAXIMUM CENTER DISTANCE .............. 36´´
HYDRAULIC TABLE FEED ................. 3 TO 240 IPM
PICK FEED AT TABLE REVERSE
VARIABLE SPEED WORKHEAD
WHEEL SIZE ........................... 12´´ X 1´´ X 6´´
COOLANT
3 HORSEPOWER WHEELHEAD MOTOR
1 HORSEPOWER HYDRAULIC MOTOR
Boyer Schultz Challenger 6 x 18 Surface Grinder: 6 x 18 Surface Grinder
Fine Line Chuck
Coolant Pump
Auto X & Y
Manual Z
Overhead Dresser
Light
Full Machine Specifications
6 x 12 Mag Chuck Fine Line
Overhead Wheel Dresser
Manual Z Axis
Coolant Pump and Kit
Model 2A618
Hydraulic X & Y
Longitudinal Table Travel 19"
Cross Feed of Table 7"
Standard Grinding Wheel Size 8"x5/8"x1-1/4" hole
Work Height Under Wheel 0" to 10-3/4"
Table Working Surface 18" x 5 5/8"
Spindle Speed-(Direct Drive) 3,400 RPM's
Hand-Wheel Graduations-Vertical .0005"
Hand-Wheel Graduations-Cross .001"
Walker Fine Line Chuck
Coolant with Coolant Tank
Over the Wheel Dresser
Light
Auto Lube
24” TIMESAVER Dry Single Drum Sander, Type 325-1-MW: 24” TIMESAVER Dry Single Drum Sander, Type 325-1-MW
Belt width 24”
EQUIPPED WITH:
Variable speed conveyor
Single drum design
Pneumatic belt tracking
Mdl. 84 Torit dust collector
40 H.P. 3/60/440 Volt Motor w/ controls
36” #18-36 BLANCHARD Rotary Surface Grinder: 36” #18-36 BLANCHARD Rotary Surface Grinder
Wet base design
Range 36” Diameter
Work height under new ring wheel 12”
Wheel size 18” x 5” x 15” cylinder
Wheel speed 720 RPM
(6) Chuck speeds 6,9,12,18,25,33 RPM
EQUIPPED WITH:
18” x 5” x 15” Cylinder wheel
36” Dia. one-piece magnetic chuck
with neutrofier controls
Power or manual down-feed of head
Power rapid traverse of wheel and table
2 H.P. table drive
25 H.P. AC Main drive Motor w/ controls
Model GRI-2000S TAISEI Internal Grinder: Model GRI-2000S TAISEI Internal Grinder
Diameter of hole to be ground 1.97” to 27.6”
Max. length of hole ground 39.4”
Max. length of work 78.7”
Max. swing inside chuck guard 33.5”
Height from table top to centerline of work over table 19.7”
Max. swing over table 39.4”
Max. stroke of table 78.7”
(6) Table grinding feeds 5.12-35.43 IPM
(6) Table rapid traverse rates 10.24-70.87 IPM
Table travel per revolution of handwheel 0.9”
Workhead spindle taper No. 5 M.T.
Workhead swivel adjustment up to 15 degrees ±
Workhead transverse adjustment:
Forward from center 3.9”
Backward from center 19.8”
Workhead transverse adjustment per
revolution of handwheel 0.24”
Infinitely variable work head speeds 10-150 RPM
Manual wheel infeed (cross feed) 0.04”
Manual wheel infeed (crossfeed) per
revolution of handwheel 0.0001”
Automatic hydraulic wheel infeed (crossfeed) per
table stroke on work radius 0.0001” to 0.0012”
Hydraulic cross & reverse arrangement of wheelhead 8”
Grinding heads spindle speed ranges 4670 to 7000 RPM
EQUIPPED WITH:
(6) Grinding spindles
(2) 4.72” Dia. x 42” reach
(1) 4.72” Dia. x 24” reach
(1) 4” Dia. x 32” reach
(1) 2 ¾” Dia. x 12” reach
(1) 1” Dia. x 12” reach
Inch calibrated wheel infeed index dial graduated to read 0.0002” per
division on work diameters
Infinitely variable workhead speeds
Automatic hydraulic wheel infeed
Hydraulic cross-traverse arrangement of wheelhead (8”)
Common mounting base for work rest and wheel dresser
Angular wheel dresser
32” Dia. faceplate with dual center
28” Dia. 4-jaw chuck
3 point roller steady rest w/ riser
Automatic cycle controls
Rapid traverse table
Chuck guard
Wheel balancing stand with mandrel
(11) Wheel mounts with grinding wheels
25” x 42” x 10 3/8” High T-Slotted auxiliary work support table
Exterior coolant system with splash guards
Automatic lubrication
2 H.P. Table feed motor
5 H.P. Workhead drive motor with ring-cone type speed variation and
work spindle controller
5 H.P. Wheel spindle drive motor
Main and auxiliary control panels
CINCINNATI-MILACRON Universal tool and cutter grinder, Model #2MT: CINCINNATI-MILACRON Universal tool and cutter grinder, Model #2MT
Swing over table 10” diameter
Swing over table with raising blocks 14” diameter
Length between right and left hand tailstocks 27”
Length between tailstock and work head 21 ½”
Range:
longitudinal 16”
cross 10”
Table working surface 6” x 36”
Table swivels 180°
Swivel table adjustments-Tange bar taper setting
device (toward & away from wheel head) 5” per foot on diameter
-Fine adjustment taper setting device
(toward& away from wheel head) 2” per foot on diameter
Table graduations in center 90°
Vertical movement of grinding wheel spindle 10 ½”
Grinding wheel head swivels 360°
Grinding wheel head tilts above & below center 15°
Maximum distance, centerline of spindle to tabletop 13 ½”
Spindle speeds, 6” wheel, surface speed 6,022 FPM-3,837 RPM
3½” wheel, surface speed 5,887 FPM-6,442 RPM
EQUIPPED WITH:
Swiveling and tilting wheel head
Swivel table
Duplicate controls operating the machine at the front, right or left hand end of the table, or at the rear, right or left hand side of the column
Anti-friction ball bearing table rolling in replaceable hardened steel v-ways
H.D. Universal work head
Left and right hand tailstocks with centers
“Tange Bar” taper setting device permitting quick and precise positioning of the swivel table when grinding tapers
1-shot lubrication system
1 H.P. 3/60/230-460 volt grinding wheel drive motor and electrical controls
12” x 60” HFS-15 BLOHM 3-Axis Hydraulic Surface Grinder: 12” x 60” HFS-15 BLOHM 3-Axis Hydraulic Surface Grinder
Table clamping surface: 12” x 86”
Max.length ground 60”
Max.width ground 16”
Max.distance from table to spindle centre line 23”
Table cross movement 14”
Longitudinal hydraulic table travel 67”
Automatic electric cross feed .08-2 9/16 inches per stroke
Longitudinal table speed 6 ½-82 FPM
Grinding wheel speeds 1400/2800 RPM
Grinding wheel size 12” x 2” x 3”
Vertical feed range 1-20 microns
EQUIPPED WITH:
Finimatic automatic incremental down-feed of wheel
Rapid traverse to wheel head
12” x 60” electromagnetic chuck w/controls
Pendant control
Over-the-wheel dresser
Coolant system
(1)wheel mount w/wheel
Vertical micrometer depth stop
Work light
7 ½ H.P. wheel drive motor
12"x 16"cc Model A KARSTENS Hydraulic Universal Grinder: 12"x 16"cc Model A KARSTENS Hydraulic Universal Grinder
Maximum swing: 11.81"
Maximum work between centers: 15.75"
Maximum wheel diameter: 15.75" x 5" diameter hole
Maximum width of wheel: 3.837"
Infinitely variable work head speeds: 30 to 450 RPM
Swivel table graduated to a maximum angle: 11 1/2 º
Maximum work piece weight between centers: 220 Lbs.
Maximum work piece weight chucking: 110 Lbs.
Infinitely variable infeed range: .00004" - .001"
Hydraulic table traverse infinitely variable: up to 236 IPM
Minimum table stroke: 1/32"
Spindle speeds: 1600/2000 RPM
Work head taper hole in spindle: No. 5 M.T.
Spindle bore: 1 ?"
Tail stock taper hole: No. 4 M.T.
Plunge grinding speed: .002 to .157 IPM
Total infeed travel of hand wheel: 3 5/32"
Swivel of work head: 90º
EQUIPPED WITH: Hydraulic operation
Swivel work head
Swivel wheel head
Swivel table
Variable work head speeds
Plunge feed
Pick feed
Fine and compensating feed control
(2) Wheel mounts
(1) New grinding wheel
.44/.89 H.P. Variable speed work head drive
5.4 H.P., 1420 RPM wheel drive motor
GIDDINGS & LEWIS (WINSLOW) Drill Point Grinder, Model HC Exactamatic: GIDDINGS & LEWIS (WINSLOW) Drill Point Grinder, Model HC Exactamatic
Drill Point type and capacities:
Conventional Point 1/16" to 1" diameter
Helical Point 1/16" to 1" diameter
Racon Point 1/16" to 1" diameter
Split Point 1/16" to 1/2" diameter
Pyrcon (four facet) 1/16" to 1" diameter
Grinding wheel size 12" diameter x 5" bore x 3/4" face
Drill point included angles from 90 degrees to 140 degrees
EQUIPPED WITH:
Capability to handle all types of 2-fluted, right hand drills
Lip clearance angle adjusted from the operator’s control console
Point angle varied from by angular adjustment of workhead
Cam action-generated rotary motion in all three axes set at the operator’s control console
Built-in cam-formed wheel dresser
(4) Wheels mounts
(6) Quick-change inch bushing plates
(9) Rubber flex collet holders from 1/16" to 3/4"
(17) Cams
Quick-change holder with (17) expandable collets from 1/16" to 1"
Aget Mistkop oil mist collector
1/8 H.P. coolant pump motor
1/4 H.P. workhead motor
1 H.P. grinding wheel drive motor and electrical controls
14” x 32” ELB Hydraulic Surface Grinder, Model SW8VAII: 14” x 32” ELB Hydraulic Surface Grinder, Model SW8VAII
Max. surface ground 14” x 32”
Max. distance, spindle center to top of table 24”
Table speed 3-90 F.P.M.
Automatic cross-feed to table with continuous
rapid traverse 47 I.P.M.
Automatic cross-feed to table, intermittent,
infinitely variable .04”-2.4” per stroke
Cross-feed hand wheel graduation .001”
Cross-fed fine adjustment .0005”
Rapid traverse rate, vertical 6 I.P.M.
Vertical feed hand wheel graduation .00005”
Automatic incremental down feed rate,
infinitely variable .0001”-.0025”
Grinding wheel size 11 ¾” dia. x 2” width x 3” bore
EQUIPPED WITH:
Electromechanically actuated incremental down-feed or grinding wheel hand
in pre-set increments at each saddle reversal for surface grinding or
at each table reversal for plunge, face and slot grinding. At conclusion
of down-feed cycle automatic return of grinding wheel hand and spark-out
of grinding wheel.
Motorized power rapid wheel hand positioning
Electric straight dressing with 2 speeds and auto. Diamond down-feed
Hydraulic table traverse with adjustable stops
Electro-mechanical cross feed ( accomplished by movement of the wheel head column)
with cross travel adjustment from front of machine
Hand wheels for manual operation
13 ¾” x 31 ½” Electro-magnetic chuck with Neutrofier control
(1)Wheel mounts
Grinding wheels
External coolant pump and tank with TORIT dust collector
6.7/8 H.P. 3/60/220 Volt spindle drive Motor and electrical controls
12" x 36" GARDNER 2-Axis Hydraulic Surface Grinder, Model 1236: 12" x 36" GARDNER 2-Axis Hydraulic Surface Grinder, Model 1236
Work table capacity 12" x 36"
Table travel: Power feed 43"
Hand feed 45"
Table speed range 0 to 100 FPM
Saddle cross travel 13-1/2"
Cross feed increments 0.016" to 0.375"
Max. distance, wheel to table 16"
Max. distance under wheel to chuck 13"
Standard wheel size 12"Dia. x 2" Wide x 3" Bore
Power elevation rate to wheel 40 IPM
Spindle speed 1800 RPM
Approx. Maximum Height under
New Wheel 9" to 10"
Equipped with:
Power elevation to wheel
Hand or power operation
2-axes hydraulic operation
(3) wheel mounts
Bijur auto. lubrication
Hardened and ground steel ball bearing mounted bed ways
12" x 36" Electro Magnetic chuck, Coarse Pole, Mfg. Inter-Lok
Wheel dresser diamond not built in
Neutrofier Vari-Power Chuck Control
Tra Vatrol Control, Type #1RL53
Controls for: Table Manual or Auto
Saddle Manual or Auto
Wheel Head Rise & Lower
Dresser Feed On & Off
Separate Coolant Tank & Pump - No filter System
Table Left End Spark Guard
(2) Adjustable Table Stops
3 HP Hydraulic System
5 H.P., 3 Phase, 60 Cycle, 230-460 Volt Spindle Drive Motor
Hydraulic System: 28" LR x 52" FB x 39" H
Coolant Tank: 20" LR x 43" FB x 26" H
Agie/Elox, Mondo 30, 3-axis Ram CNC Electrical Discharge Machine: Agie/Elox, Mondo 30, 3-axis Ram CNC Electrical Discharge Machine
SPECIFICATIONS:
• Work Table (L x W)………………………………25.6" x 20'
• Maximum Part Weight……………………………1000 lbs
• Maximum Open Height……………………………22.2"
• Travels (x, y, z)…………………………………14" x 12'' x 9.8"
• Work Tank (L x W x H)………………………35.8" x 26.7" x 15.7''
• Electrical Requirements…………………190, 208, 230, 250, 400, 415, 460, 500V / 3Ph / 50/60 Hz
• Service Requirements…………………………Water & Air
• Dielectric Capacity……………………………140 Gallons
EQUIPPED WITH:
• Complete Dielectric Coolant and Filtration System
• Agie/Elox 3-axis, 50 Amp Controller with CRT, Futura III 2PM, SN AF 1112PM000014
• Hand Pendant Controls
• Manual
EDM, Chevalier, DM-323 Conventional, Ram Type, Sinker: Sokki DU1003 3-Axis DRO
20 Amp Power supply
29.5" x 18.9" x 11.8" Tank Dimensions
19.7" x 11.8" Work Table
11.8" x 7.9" X-Y Travels
1,100 lbs Max. Workpiece Weight
7.9" Quill Stroke
20.9" Distance from table to electrode holder plate
132 lbs. Maximum electrode load
Anti-arc device
Auto fire extinguisher
Pulse-pressure-vacuum flushing
Micrometer depth gauge
Worklight
5,719 Hours of Work Time
OMEGA 405-D CNC Ram type EDM Machine: OMEGA 405-D CNC Ram type EDM Machine
Work table size 17.7” x 9.8”
Work tank internal dimensions 32.7” x17.7” x 11”
Fluid level adjusting range 5.7”-11.4”
X-axis travel 9.8”
Y-axis travel 5.9”
Z-axis travel 8.6”
Distance from top of work table to surface of electrode holder 17.3”
Electrode holder dimensions 5.5” x 5.5”
Distance from floor to work table top 34”
Z axis servo mode DC Servo
Max. weight of electrode 110 lbs
Max. weight of work piece 1100 lbs
Dielectric tank capacity 500 liters
Max. machining current 30 amps
EQUIPPED WITH:
2- paper core fluid filtration mode
Submersive type tank
Electrode holder
Head depth measuring device
Sparkmaster Micro-computer current
pulse generator control
Input total power 4 KVA
1996 Agie Mondo Futura III: Amp
15" x 12" x 8.5" Travels
Oversize Tank
Hi POL
Floppy
Low Hours
Excellent Condition
Under Power!!!
Full Machine Specifications
40 AMP
X =15.0", Y=12.0", Z=8.5" (Approx)
Special Options Include
Oversize tank for large jobs or multiple set-ups
Hi POL
Floppy Disc Reader
Equipped With 3R ttoling and Haas Index Head which
are available, but not included in the price
Low hours, well maintained
We found 2 matching ads. Now displaying the remaining 2 ads.
SUPERIOR MODEL 3VB/HD-10 VERTICAL HONE: SUPERIOR MODEL 3VB/HD-10 VERTICAL HONE
HEAVY DUTY
FULLY AUTOMATIC OPERATION AFTER INITIAL SET-UP
DIAMETER CAPACITY: UP TO 10"
LENGTH CAPACITY: 36"
STROKE: 60"
TABLE SIZE: 18" X 24"
DISTANCE, FLOOR TO TABLE TOP: 8"
MOTOR: 3 HP
EQUIPPED WITH:
FREE STANDING HYDRAULIC POWER UNIT
DWELL/CYCLE TIMER
STOP FEED (EXPANSION) SPARKOUT SYSTEM
AUTO SIZING
CONTROL CONSULE
8" 3-JAW CHUCK
24" EXTENSION WORK TABLE
OAD: 54" L-R X 57" F-B X 124" HIGH - MACHINE
28" L-R X 18" F-B X 31" HIGH - HYDRUALIC UNIT
36" L-R X 24" F-B X 56" HIGH - CONTROL CABINET
HYDRAULIC HORIZONTAL EXTERNAL HONING MACHINE: BARNES MODEL 5E HYDRAULIC HORIZONTAL
---EXTERNAL HONING MACHINE-- ONLY
SWING: NOT LESS THAN 12" DIAMETER
HONING CAPACITY: UP TO 6" DIAMETER
LENGTH OF STROKE, ADJUSTABLE (CARRIAGE TRAVEL):
2" - 12'
RATE OF CARRIAGE TRAVEL: 10 - 100 FPM
SPINDLE SPEEDS (VAR): 50 TO 473 RPM
CAPACITY BETWEEN CENTERS: 2' - 12'
SPINDLE TAPER: NO. 5 MT
RESERVOIR CAPACITY: 80 GALLONS MINIMUM
100 GALLONS MAXIMUM
MOTORS: 15 HP MAIN DRIVE
15 HP HYDRAULIC
3/4 HP COOLANT PUMP
EQUIPPED WITH:
OPERATOR CONTROL STATION
COOLANT SYSTEM WITH MAGNETIC & FABRIC FILTRATION
OAD: 248: L-R X 66" F-B X 61" HIGH - MACHINE
93" L-R X 16" F-B X 75" HIGH - ELECTRICAL CABINET
71" L-R X32" F-B X 68" HIGH - HYDRAULIC UNIT
77" L-R X 57" F-B X 70" HIGH - COOLANT/FILTRATION UNIT
NOTE - MACHINE IS IN EXCELLENT CONDIJTION. FROM U.S. GOVERNMENT RESERVE.
We found 2 matching ads. Now displaying the remaining 2 ads.
SAMPUTENSILLI Model SCT-3 Gear Chamfer Machines: AB Panelview 900
The Samputensili Chamferer and Deburrer is a universal
style machine for shafts and gears.
SPECIFICATIONS:
Max. Workpiece Diameter .98"-13.78"
Max. Module 3.175 DP
Face Width Range .157"-4.134"
Max. Workpiece Length
- with gearing in center of workpiece 29.53"
- with gearing at one end of workpiece 19.69"
Tool Spindle drive Output, Approx. 2 HP
Total Connected Load of Machine 5-8 HP
Compressed Air Pressure 5 Bar
Compressed Air Consumption, approx. 50-70 l/min.
USED 10' X 1/2" ALLSTEEL MODEL E CNC HYDRAULIC SHEAR: USED 10' X 1/2" ALLSTEEL MODEL E CNC HYDRAULIC SHEAR
CAPACITY: 1/2" M.S.
3/8" S.S.
CUTTING LENGTH: 120"
BACK GAUGE LENGTH: 36"
RATED RAKE ANGLE: 5/8"
GAP: 12"
NUMBER OF HOLDDOWNS: 16
SPEEDS: 9/40 SPM
MAIN MOTOR: 40 HP
ELECTRICS: 575/3/60
EQUIPPED WITH:
ALLSTEEL CNC BACKGAUGE
46" SQUARING ARM
(2) FRONT SUPPORT ARMS
SHADOW LINE CUTTING GUIDE
REAR SAFETY SWING-UP CAGE
OPERATORS MANUAL
USED 14' X 3/4" CINCINNATI MODEL 10014 MECHANICAL POWER SQUARING SHEAR: USED 14' X 3/4" CINCINNATI MODEL 10014 MECHANICAL POWER SQUARING SHEAR
THICKNESS CAPACITY: 3/4" (MILD STEEL)
NOMINAL CUTTING LENGTH: 168" (14')
LENGTH BETWEEN HOUSINGS: 14'-3"
STROKES PER MINUTE: 20
FLYWHEEL RPM: 600
BACK GAGE RANGE: 48"
HOLDDOWN TO KNIFE EDGE: 1-3/8"
DISTANCE UNDER HOLDDOWN: 1-1/2"
TOTAL HOLDDOWN PRESSURE: 51 TONS
RAKE (SHEAR ANGLE): .478" TAPER PER FOOT
RAM ADJUSTMENT: 1-1/4"
SIZE FOUR-EDGE KNIVES: 1-3/4" X 6-1/2"
LENGTH OF KNIVES: 14'-5"
THROAT: 24"
MAIN MOTOR: 40 HP
EQUIPPED WITH:
48" BACK GAGE
12' SQUARING ARM
(2) FRONT SUPPORT ARMS
USED 10' X 3/4" PACIFIC MODEL 750R-10 HYDRAULIC PLATE SHEAR : USED 10' X 3/4" PACIFIC MODEL 750R-10 HYDRAULIC PLATE SHEAR
RATED CAPACITY:
MILD STEEL PLATE CONT. RATED CAPACITY - 3/4"X10'
MAXIMUM MILD STEEL PLATE CAPACITY - 1" X 10'
MAXIMUM STAINLESS STEEL PLATE CAP. - 3/4" X 10'
MAXIMUM SHEAR LENGTH: 10'
EQUIPPED WITH:
FRONT OPERATED POWER BACK GAUGE
(12) FRONT HOLD DOWNS
SQUARING ARM
(2) STOCK SUPPORTS
(1) EXTRA SET SHEAR BLADES
HTC MODEL 500-10 HYDRAULIC SHEAR: HTC MODEL 500-10 HYDRAULIC SHEAR
Capacity: 10' x 1/2" Mild Steel
Distance Between Housings: 10'4"
Speeds: 123 IPM - Down
192 IPM - Up
Number of SPM (Full Width Cut): 9.5
Number of Holddown Cylinders: 11
Rake Angle: 1/2" per Foot
All Steel Construction
EQUIPPED WITH:
36" Front Operated Power Back Gauge
(2) Front Support Arms
(1) Pair 4-Edge Knives
40 HP AC Main Drive (Pump) Motor
DC Backgauge Motor
Electrical Controls
Electric Foot Switch Operation
WYSONG & MILES MODEL 1025 MECHANICAL POWER SQUARING SHEAR: WYSONG & MILES MODEL 1025 MECHANICAL POWER SQUARING SHEAR
Capacity: 10' x 1/4" (Mild Steel); 10' x 7 Ga. (Stainless)
Overall Length of Knives: 124"
Rake of Upper Blade: 3/8"
Speed: 55 SPM
Air Actuated Mechanical Clutch
Optional Single Stroke or Continuous Operation
Full Length T-Slot Across Bed Face
Self-Compensating, Cam Operated Power Holddowns
EQUIPPED WITH:
Wysong Power Operated Computerized LED Gauging System
36" Power Back Gauge
48" Power Front Gauge
Squaring Arm (9 Ft. Long)
(2) Front Support Arms
(1) Pair 4-Edge Knives
Bijur Automatic Lubrication System
Knife and Holddown Guard
10 HP AC Main Drive Motor
Electrical Controls
Electric Foot Switch Operation
Rack with Extra Set of Blades
LVD MODEL HST-E 50/10 HYDRAULIC POWER SHEAR: LVD MODEL HST-E 50/10 HYDRAULIC POWER SHEAR
Capacity: 10' x 1/2" (Mild Steel)
Overall Length of Blades: 123"
Distance Table to Floor: 39-1/2"
Self-Compensating Hydraulic Holddowns
All Steel Welded Frame Construction
EQUIPPED WITH:
LVD MNC-10 CNC Control
Pneumatic Sheet Holder (Rear Mounted)
Moveable Scrap Bin
40" Front Operated Power Back Gauge
(1) Pair 4-Edge Knives
(1) Extra Set of New Knives
12 Ft. Squaring Arm
(2) Front Support Arms
AC Main (Pump) Drive Motor
Electrical Controls
Self-Contained Hydraulic Power System
Electric Foot Switch Operation
6’ x ¼” BETENBENDER Hydraulic Shear: 6’ x ¼” BETENBENDER Hydraulic Shear
Shearing length 72”
Shearing capacity, mild steel ¼”
Blade size 1” x 4”
Table height 32”
Length of blades 76”
Rake angle per rated capacity ¼”
Speed 19 SPM
Number of hold downs 13
EQUIPPED WITH:
36” cap. front operated power back gage
48” R.H. Squaring arm
Rear scrap chute
Remote foot pedal control
Production counter
Work light
15 H.P. Motor and controls
AC Electrics
10' X 1/4" HTC MODEL 250-10A POWER SQUARING SHEAR: 10' X 1/4" HTC MODEL 250-10A POWER SQUARING SHEAR
CAPACITY: 1/4"
CUTTING WIDTH: 124"
DECK HEIGHT: 32"
BLADE SIZE: 1" X 3"
RAKE ANGLE/FOOT: 11/32"
NUMBER OF HOLDDOWNS: 9
CYCLES: 23 - FULL WIDTH CUT
38 - HALF WIDTH CUT
69 - 12" CUT
SPEED: 220 IPM DOWN
293 IPM UP
MOTOR: 25 HP
EQUIPPED WITH:
36" FRONT OPERATED POWER BACKGAUGE-needs work
4' SQUARING ARM
SHADOW LIGHT
SWING ARM BACK STOP
4-WAY BLADES
STROKE LENGTH CONTROL
FOOT PEDAL
14' X 1´´ CINCINNATI POWER SQUARING SHEAR: 14' X 1´´ CINCINNATI POWER SQUARING SHEAR:
CAPACITY ......................... 1´´
OVERALL LENGTH OF BLADES ......... 14'5´´
DISTANCE BETWEEN HOUSING ......... 14'3´´
DEPTH OF GAP ..................... 24´´
FRONT OPERATED POWER BACKGUAGES .. 48´´
STROKES PER MINUTE ............... 20
HYDRAULIC HOLD DOWNS ............. YES
SQUARING ARM ..................... 10'
DUAL PALM BUTTONS ................ YES
MOTOR ............................ 50 HORSEPOWER
6' X 1/2´´ COLUMBIA POWER SQUARING SHEAR: 6' X 1/2´´ COLUMBIA POWER SQUARING SHEAR:
CAPACITY ........................... 1/2´´
LENGTH OF BLADES ................... 76´´
DISTANCE BETWEEN HOUSINGS........... 6'4´´
FRONT OPERATED BACK GAUGE .......... 36´´
STROKES PER MINUTE ................. 40
DEPTH OF GAP ....................... 18´´
SQUARING ARM ....................... 48´´
AIR CLUTCH ......................... YES
FLOOR STANDING ..................... YES
MOTOR .............................. 15 HORSEPOWER
10' X 1/4´´ WYSONG POWER SQUARING SHEAR: 10' X 1/4´´ WYSONG POWER SQUARING SHEAR:
CAPACITY .......................... 1/4´´
FRONT OPERATED POWER BACKGUAGES ... 36´´ (PC 100 CONTROL)
SQUARING ARM ...................... 10'
FRONT ARM SUPPORTS ................ (3)
HYDRAULIC HOLDDOWNS ............... 16
FLOOR TO TOP OF TABLE ............. 32´´
BIJUR LUBE ........................ YES
BACK GUAGE MOTOR .................. 3/4 HORSEPOWER
MAIN MOTOR ........................ 15 HORSEPOWER
12' X 3/8´´ CINCINNATI POWER SQUARING SHEAR: 12' X 3/8´´ CINCINNATI POWER SQUARING SHEAR:
CAPACITY .......................... 3/8´´
LENGTH OF BLADES .................. 12'3´´
FRONT OPERATED POWER BACK GAUGE ... 48´´
DEPTH OF GAP ...................... 19-1/4´´
STROKES PER MINUTE ................ 50
HYDRAULIC HOLDDOWNS ............... YES
LIGHT BEAM SHEARING ............... YES
MOTOR ............................. 15 HORSEPOWER
1978 HTC/ Pacific Hydraulic Squaring 500-12A HC: 1978 HTC/ Pacific Hydraulic Squaring 500-12A HC
48" Power Back Gauge
Left Hand Squaring Arm
3 Position Foot Pedal
Full Machine Specifications
Capacity in Mild Steel 1/2"
Max Shearing Length 148"
Speed (Cutting) 120 IPM
Speed (Return) 187 IPM
Stroke Per Minute (Adjustable) 8-12
Motor 40 HP
Equipped With:
48" Power Front Operated Back Guage
Left Hand Squaring Arm
Power Blade Clearance
Power Rake Adjustment
High Rake Angle
3-Position Foot Switch
8' x 3/16" Lodge & Shipley Mechanical Shear, Model 0308: 8' x 3/16" Lodge & Shipley Mechanical Shear, Model 0308
Flush floor design, no pit required
Capacity in mild steel: 3/16" x 8'
Distance between housings: 8'4"
Blade size (4 edge): 1" x 4" x 100"
Blade rake per foot: 1/4"
Speed: 60 SPM
Hold down pressure: 5 1/2 Tons
Hold down to cutting edge - adjustable: 5/8" to 1 5/8"
Throat depth: 18"
Back gauge range: 36"
Front gauge range: 50"
Floor to top of table: 32"
Centers of hold downs: 11 1/2"
Equipped With: 36" Capacity front operated motorized back gauge
(2) Front arms
(1) Set of blades
Air clutch w/spring brake
Remote electric foot pedal control
Hydraulic hold-downs
Automatic pressure lubrication
Variable blade clearance adjustment
Ram counter balances
5 H.P. 3/60/208-220-440 Volt motor and controls
Floor Space: (without arms) 133"LR x 75"FB x 68"High
10’ x 1/2" LODGE & SHIPLEY Mechanical Shear with air clutch, Mdl. 0810: 10’ x 1/2" LODGE & SHIPLEY Mechanical Shear with air clutch, Mdl. 0810-SL
Requires 3 1/4" depth pit for apron
Capacity, mild steel 1/2" x 10'
Distance between housings 10’ 4"
Blade size (4 edge) 1 1/8" x 5" x 124"
Blade rake per foot 3/8"
Speed 40 SPM
Total hold-down pressure 18 1/2 Tons
Hold-downs to cutting edge adjustable 1 1/8"-2"
Gap 18"
Back gauge range 48"
EQUIPPED WITH:
48" capacity front operated motorized back gauge
(2) front arm extensions (36")
10’ L.H. squaring arm
Extra set of blades
Light beam shearing gauge
Ram counter balances
Variable blade clearance adjustment with indicators
Air clutch with spring brake
Hydro-pneumatic hold-down system
Built-in ball transfers in table
Inclined slide in rear for scrap
Automatic pressure lubrication
Remote electric foot pedal control
15 H.P. 3/60/220-440 volt motor with controls
10' X 1/4´´ CINCINNATI POWER SQUARING SHEAR: 10' X 1/4´´ CINCINNATI POWER SQUARING SHEAR
CAPACITY ............................. 1/4´´
LENGTH OF BLADES ..................... 10'4´´
FRONT OPERATED POWER BACK GAUGE ...... 36´´
DEPTH OF GAP ......................... 18´´
STROKES PER MINUTE ................... 60
AUTO LUBE ............................ YES
HYDRAULIC HOLD DOWNS ................. 11
DISTANCE UNDER DOWN .................. 1/2´´
SQUARING ARM ......................... 48´´
FRONT ARM SUPPORT .................... YES
FULL LENGTH FOOT TREADLE ............. YES
MAIN MOTOR ........................... 7-1/2 HP
12' X 1/2´´ HTC POWER HYDRAULIC SQUARING SHEAR: 12' X 1/2´´ HTC POWER HYDRAULIC SQUARING SHEAR
CAPACITY ........................... 1/2´´ MILD STEEL
OVERALL LENGTH OF BLADES ........... 148´´
FRONT OPERATED POWER BACK GAUGE .... 48´´
GAP ................................ 24´´
NUMBER OF HYDRAULIC HOLD DOWNS ..... 13
SWING AWAY BACK GAUGE .............. YES
RAKE ANGLE ......................... 1/2´´ PER FOOT
ELECTRIC FOOT TRIP ................. YES
KNIVES SPEED DOWN .................. 120 IPM
KNIVES SPEED RETURN ................ 180 IPM
STROKES PER MINUTE ................. 8 FULL STROKE
STROKES PER MINUTE ................. 12 HALF STROKE
MAIN MOTOR ......................... 40 HORSEPOWER
1984 Cincinnati 2CC10 10' x 1/4" Mechanical Shear: 1984 Cincinnati 2CC10 Mechanical Power Squaring Shear
7.5 HP
Strokes Per Min 60
* All machinery specifications must be independently verified by buyer. All machinery sales are subject to prior sale. Any agreement to purchase or sell machinery must be in writing.
Full Machine Specifications
Capacity 1/4"
Distance Between Housing 10'3"
Back Gauge Range 0-36"
Rake Taper Per Foot 1/4" Per Foot
Strokes Per Minute 60
Hydraulic holdowns 11
Gap (Between Housing and Table) 4"
Main Drive Motor 7.5 HP
Equipped With:
Microcomputer Gauge Control (Front & Back Guages)
(2) Cincinnati Front Gauge Arms 48" & 72"
Continental Conveyor
Capacity 20 Gauge 1/4"
Conveyor Speed 1800 Per Min
# of Conveyor Belts 5
Sheet Supports 18
Continental Sheet Stacker
(3) Front Support Arms
4 Back Gage Probes for Automatic Operation
Electric Foot Switch
Automatic Pressure Lubrication
Interlocked Steel Construction
Light Bar
Non Float Inclined Ram
Main Motor 7.5 HP/3PH/60C
1985 Accurshear 8100016 Hydraulic Shear: 1985 Accurshear MDL 8100016
Rated capacity 1"x16' Mild Shear
26 Hydraulic Holddowns
80,000 Tensile Strength
* All machinery specifications must be independently verified by buyer. All machinery sales are subject to prior sale. Any agreement to purchase or sell machinery must be in writing.
Full Machine Specifications
Pendant Control with Sector Switch
Rated Capacity 1"x16' Mild steel
Tensile Strength 80,000
Ball Transfers in Table
Fixed Rake Angle
Power Adjustment of Blade Clearance
4 Sided Blades
26 Hydraulic Holdowns
Manuals
4 Strokes Per Min
Adjustable Control
Moveable Foot Pedal
Equipped With
13' Squaring Arm
48" Front Operated Power Back Guage Swing
75 HP
3" Leaf Plate
10 Ga. Capacity NIAGARA Ring and Circle Cutting Shear, Model 31RC: 10 Ga. Capacity NIAGARA Ring and Circle Cutting Shear, Model 31RC
Capacity in mild steel 10 gauge
Minimum/Maximum circle diameter from square 6"/60"
blanks
Minimum/Maximum circle diameter from octagonal 6"/78"
blanks
Throat depth, cutters to frame 18-1/2"
Throat of circle arm 43"
Diameter of cutters 3"
Circumferential speed of cutters 100 F.P.M.
EQUIPPED WITH:
Air actuated clamping device with dual electric push buttons for clamping and
unclamping of circle arm
Air actuated feed of cutting head with adjustable timer to control duration of cut
Dual regulating valves for controlling clamping and feed pressure
Key lock selector switch for hand/off/auto mode of operation
Dual electric palm buttons to start cutting cycle
Emergency stop button
Manually adjustable cutter clearance
Hand crank for positioning of circle arm on a rack in order to cut various diameters
3 H.P. 3/60/230-460 volt drive motor with electric brake and electrical control cabinet
45 ton W.A. WHITNEY Hydraulic Angle Shear, Model 609-250: 45 ton W.A. WHITNEY Hydraulic Angle Shear, Model 609-250
Capacity 45 tons
Shearing capacity 6”x6”x1/2”
EQUIPPED WITH:
Remote pendant control
14’ Stock feed table
Hydraulic power unit
Work light
10’ x 1/2” BERTSCH Series 500, Model 8-120, Hydraulic overdriven Shear: 10’ x 1/2” BERTSCH Series 500, Model 8-120, Hydraulic overdriven Shear
All steel construction, flush floor, no pit required
Shearing length 120”
Shearing capacity ½” mild steel
Back gage range 48”
Nominal rake ½”
Number of hold-downs 10
Hold-down tonnage 40
Blade size 1” x 4”
Ram speed down 1.82 in/sec.
Ram speed up 4.6 in/sec.
Cycles, full cut 10
Cycles, half width cut 19
EQUIPPED WITH:
48” 2-Speed front operated power back gage with display and
swing away feature
4-edge blades
10’ R.H. Squaring arm with scale and stop
48” front arm extensions
Adjustable of rake angle
Manual blade clearance adjustment
Remote electric foot pedal control
Light beam shearing gage
Built-in ball transfers in table
Trabon one-shot lubrication
60”x 144”x 33” High portable steel work support table with
built-in ball transfers and casters (front location)
40 HP 3/60/230-460 Volt Motor and controls
Dimensions: Shear only (does not include front arms): 163” LR x 115 ½”FB x 121”High
LVD MODEL 350BH15 CNC HYDRAULIC PRESS BRAKE: LVD MODEL 350BH15 CNC HYDRAULIC PRESS BRAKE
Capacity: 350 Ton
Overall Length of Bed and Ram: 15'
Distance Between Housings: 12'6"
Stroke: 11.8" (Maximum)
Open Height: 15.75"
Throat Depth: 22.4"
Speeds: 236 IPM - Advance
30 IPM - Pressing
283 IPM - Return
Width of Bed Top: 10.6"
All Steel Welded Construction
Flush Floor Design
EQUIPPED WITH:
LVD Model MNC-95/C 5-Axis Control System
4-Axis Back Gauge
Sectional Ram Clamps
60 HP AC Main (Pump) Drive Motor
Self-Contained Hydraulic Power Unit
Electrical Controls
Sight Type Oil Level Gauge
BENDING CAPACITY:
15' x 3/8"
WYSONG MODEL RT-140-122 CNC HYDRAULIC PRESS BRAKE: WYSONG MODEL RT-140-122 CNC HYDRAULIC PRESS BRAKE
Capacity: 140 Ton
Overall Length of Bed & Ram: 10'2"
Distance Between Housings: 8'6"
Stroke: 8"
Die Space: 17"
Closed Height: 9"
Throat Depth: 12"
Distance Bed to Floor: 32"
Speeds: 236 IPM - Advance
16 IPM - Pressing
155 IPM - Return
Flush Floor Design
Welded Steel Construction
EQUIPPED WITH:
Cybelec DNC 90 6-Axis CNC Control with Color Graphics
Programmable 4-Axis Back Gauge
Hydraulic Die Clamping (Ram and Bed)
Automatic Lubrication System
10 HP AC Main (Pump) Drive Motor; Electrical Controls
Dual Palm Button or Electric Foot Switch Operation
BENDING CAPACITY:
10' x 3/16"
250 TON VERSON 24´´ X 157´´ BED MECHANICAL POWER PRESS BRAKE: 250 TON VERSON 24´´ X 157´´ BED MECHANICAL POWER PRESS BRAKE
FLOOR STANDING .................... YES
FLANGED BED AND RAM ............... YES
CAPACITY .......................... 250 TON
STROKE OF RAM ..................... 8´´
RAM ADJUSTMENT .................... 6´´
SHUT HEIGHT, SDAU ................. 22´´
AREA OF BED ....................... 157´´ X 24´´
AREA OF RAM ....................... 150´´ X 24´´
DISTANCE BETWEEN HOUSINGS ......... 102´´
STROKES PER MINUTE ................ 24
DEPTH OF THROAT ................... 13´´
DOUBLE BACK GEARED ................ YES
MOTORIZED RAM ADJUSTMENT .......... YES
AIR CLUTCH & BRAKE ................ YES
AIR COUNTER BALANCE ............... YES
MOTOR, HORSEPOWER ................. 25
375 TON X 14' DREIS & KRUMP PRESS BRAKE: 375 TON X 14' DREIS & KRUMP PRESS BRAKE:
CAPACITY ............................ 375 TONS
OVERALL LENGTH OF BED AND RAM ....... 14'6´´
DISTANCE BETWEEN HOUSINGS ........... 12'6´´
LENGTH OF STROKE .................... 6´´
POWER ADJUSTMENT .................... 6´´
SHUT HEIGHT, SDAU ................... 18´´
DEPTH OF THROAT ..................... 10´´
STROKES PER MINUTE .................. 25
AIR CLUTCH .......................... YES
AUTO LUBRICATION .................... YES
PUSH BUTTON CONTROLS ................ YES
AIR COUNTERBALANCE .................. YES
MOTOR ............................... 20 HORSEPOWER
55 TON X 8' DREIS & KRUMP BRAKE: 55 TON X 8' DREIS & KRUMP BRAKE:
CAPACITY ....................... 55 TON AT BOTTOM
BENDING CAPACITY ............... 8' X 14 GAUGE
LENGTH OF BED .................. 8'
DISTANCE BETWEEN HOUSINGS ...... 6'6´´
STROKE OF RAM .................. 3´´
POWER RAM ADJUSTMENT ........... 3´´
DIE SPACE SDAU ................. 12´´
DEPTH OF THROAT ................ 8´´
STROKES PER MINUTE ............. 40
FORWARD & REVERSE............... YES
MECHANICAL CLUTCH .............. YES
FULL LENGTH FOOT TREADEL ....... YES
MOTOR .......................... 3 HORSPOWER
30 TON X 6'6´´ VERSON PRESS BRAKE: 30 TON X 6'6´´ VERSON PRESS BRAKE:
CAPACITY ............................... 30 TON
BENDING CAPACITY ....................... 10 GAUGE X 66´´
OVERALL LENGTH OF BED & RAM ............ 78´´
DISTANCE BETWEEN HOUSING ............... 62´´
STROKE ................................. 2-1/2´´
SHUT HEIGHT (SDAU) ..................... 7-1/2´´
RAM ADJUSTMENT (POWER) ................. 3´´
DEPTH OF THROAT ........................ 7´´
STROKES PER MINUTE ..................... 40
FRONT ARM SUPPORT ...................... YES
MANUAL BACK GAUGE ...................... YES
AIR FOOT TRIP .......................... YES
ADJUSTMENT MOTOR ....................... 1/2 HORSEPOWER
MAIN MOTOR ............................. 3 HORSEPOWER
70 TON X 6' PACIFIC HYDRAULIC PRESS BRAKE With CNC Back Gauge: 70 TON X 6' PACIFIC HYDRAULIC PRESS BRAKE
CAPACITY ................................. 70 TON
OVERALL LENGTH OF BED & RAM .............. 72´´
DISTANCE BETWEEN HOUSINGS ................ 51-1/2´´
STROKE OF RAM ............................ 8´´
OPEN HEIGHT .............................. 15´´
CLOSED HEIGHT ............................ 7´´
DEPTH OF THROAT .......................... 6´´
AUTO GAUGE CNC BACK GAGE MODEL ........... 1000
ELECTRIC FOOT TRIP ....................... YES
MILLED & DRILLED FOR ANGLES .............. YES
MOTOR .................................... 12-1/2 HORSEPOWER
10' X 12 GA DREIS & KRUMP POWER BOX & PAN BRAKE: 10' X 12 GA DREIS & KRUMP POWER BOX & PAN BRAKE
CAPACITY ............................. 12 GAUGE @ 10'
OVERALL BENDING LENGTH ............... 10'1´´
FLOOR TO BED ......................... 36-1/2´´
CONTROLS ............................. NORMAL/JOG/UP/DOWN
FINGERS .............................. FULL SET OF FINGERS
MOTOR ................................ 3 HORSEPOWER
135 TON X 10' CINCINNATI MODEL #5 PRESS BRAKE With CNC Back Gauge: 135 TON X 10' CINCINNATI MODEL #5 PRESS BRAKE
OVERALL LENGTH OF BED ...... 10'
DISTANCE BETWEEN HOUSINGS .. 8'6´´
STROKE ..................... 3´´
MILLED AND DRILLED FOR ANGLES
FLOOR STANDING
CNC BACK GUAGE ............. AUTOBEND 4
1989 Adira QH 150-40 Hydraulic Press Brake: Adira 165 ton x 13'
Length Bed & Ram 13'3.4"
10'-2" between housings
Stroke 4"
24" Motorized Back Gage
Full Machine Specifications
Capacity 165 Tons
Length of Bed and Ram 13'3.4"
Distance Between Housings 10'2"
Stroke 4"
Open Height 3.4"
Open Height with Punch Holder 9.25"
Throat Clearance 17.72"
Back Guage Speed X Axis 45 Inch per Min
Main Motor Hoursepower 12HP
Oil Tank Capacity 26.5 US Gallons
Equipped With
Adira 24" Motorized Back Guage
Variable Tonage
Swing Down 4-Way Die Lifter
Sectional Ram Clamps
no tooling included
1956 Dries & Krump 5510D 300 Ton Mechanical Press Brake: 300 Ton Mechanical Press Break 12’ Length of Bed
4” Stroke
200 ton at mid stroke
10’6” Between Housings
40H.P.
Full Machine Specifications
ISB PC 200 Press Brake Control
Capacity (Near Bottom of Stroke) 300 Tons
Capacity (Mid Stroke) 200 Tons
Overall Length of Bed & Ram 12'
Distance Between Housings 10'6"
Stroke 4"
Shut Height (SDAU) "
Ram Adjustment (Power) 6"
Strokes Per Minute 30
Throat 8"
Main Motor Horsepower 40
Equipped With
ISB PC 200 Press Brake Control Featuring
Forward reverse operation
90 Degree stop test
Stroke Stop Control
Inch Single Stroke Operation
Ground Fault Indicator
AC on/off key selector switch
Programmable top stop Overturn Brake Monitor
& Motion Detector
Air Solenoid, valves, cylinder & actuator
Electric Soot Switch
Air Actuated Clutch
Tilting Ram Adjustment with Dual Indicators
Bed & Ram Machined for Angles
Bolt on Angle Brackets
Automatic Lubrication System
Forward/Reverse Main Motor Controls
1996 Trumpf V130 10' x 144 Tons CNC Press Brake: Full Machine Specifications
Delem DA-65 Multi Axis Control
Capacity 144 Tons
Overall Length of Bed & Ram 120'
Distance between Housings 106"
Stroke 8.5"
Open Height 19"
Closed Height 10.5"
Throat Clearance 16"
Maximum Inclination of Ram 0.4"
Speeds
Form: 2-24" Per Min
Return: 320" Per Min
Distance Floor to Top of Bed 34"
Width at Top of Bed 4.75"
Operating Height 41"
Oil Capacity 66 US Gallons
Main Motor HP 25 HP
Control Features
Dalem DA-65 Multi Axis Control
Off Line Capable
Programmable Forming Speeds
Programmable Ram Opening
Programmable Reversal
Programmable Tonage Displayed Through CRT
Specs Continued
Travel 23.6"
Max Speed 200" Per Min
R-Axis Travel 9.8"
Max Speed 1900" Per Min
2 Back Guage Fingwer Supports
Fully Programmable Back Guage Speeds
Equipped With
Programmable Lower Tool Holder Crowning Adjustment
Full Tonage Throughout Stroke
Precision Ram Leveling with Dual Linear Glass Scale
Electric Foot Switch
Pedestal Palm Button Station
Full Safety Enclosure
ISB Pro Light Curtains
Manuals
4' x 17 Ton DI-ACRO Hydra-Mechanical Press Brake, Model 14-48-2: 4' x 17 Ton DI-ACRO Hydra-Mechanical Press Brake, Model 14-48-2
Rated tonnage 17 ton
Overall length of bed and ram 48"
Clear distance between housings 36-1/4"
Bending capacity (mild steel on full bed) 14 gauge
Variable work stroke setting 0 to 1" in 1/4" increments
Variable total stroke setting 1/2" to 2" (1/2", 1" & 2")
Speed ranges (depending upon total stroke setting, 17,23,24,25,26,27,28 & 50 S.P.M.
work stroke setting, and stroke speed control setting)
Shut height - bed down, stroke down 9"
Bed adjustment, ram adjustment 2"
Die holder height 3"
Throat clearance from center of dies 6"
EQUIPPED WITH:
Hydra-mechanical operation: the up and down movement of the ram is obtained from
an eccentric shaft. This shaft is powered by a specially-designed hydraulic motor.
Dual speed operating cycle: allows for pre-set of fast ram approach and slow forming.
Instant ram reverse. Ram inching for scribed line work.
Front operated micrometer back gauge calibrated to .001"
Slo/Hi-Slo/Hi-Stop Slo cycle control selector switch
Off/Setup/Run mode selector switch
Ram mounted palm buttons for cycling ram
Ram mounted "Emergency Stop" and "Ram Open" palm buttons
Remote electric foot pedal
Dual ram adjustment indicators for measurement of ram adjustment and tilt
Full complement of sectional ram clamps
Bottom die holder
Manually operated TRABON lubrication pump
3 H.P. 3/60/230-460 volt hydraulic pump motor and electrical controls
440 ton LVD Model PPN400/4500 Hydraulic Press Brake: 440 ton LVD Model PPN400/4500 Hydraulic Press Brake
Max. capacity 440 tons
Overall length of bed and ram 177”
Distance between housings 148”
Throat depth 11.8”
Shut height 21.65”
Ram adjustment 8.66”
Max. stroke 11.8”
Bed width 9.8”
Capacity of back gage system 40”
Approach speed 188 IPM
Pressing speed 21.5 IPM
Return speed 187 IPM
EQUIPPED WITH:
40” cap.front operated motorized back gage system
Hydraulic tool clamping
Lower die holder
Remote palm and foot control pedestal
48 H.P. Main Drive Motor
Requires: 47.2” pit depth for bed
Dimensions from floor level: 269”LRx 136.2”Wx 162” Height from proposed floor level
We found 6 matching ads. Now displaying the remaining 6 ads.
USED 10' X 2-1/4" BERTSCH MODEL 30/25 INITIAL PINCH PLATE BENDING ROLL: USED 10' X 2-1/4" BERTSCH MODEL 30/25 INITIAL PINCH PLATE BENDING ROLL
CAPACITY: 10' X 2-1/4" BOILER DUTY
10' X 1-3/4" PIPE DUTY
ROLL DIAMETER: 25"
LENGTH OF ROLLS: 10'2"
AIR DROP END
POWER ROLL ADJUSTMENT
MAIN DRIVE MOTOR: 125 HP
USED 12' X 3/4" BERTSCH MODEL 14 INITIAL PINCH PLATE BENDING ROLL: USED 12' X 3/4" BERTSCH MODEL 14 INITIAL PINCH PLATE BENDING ROLL
CAPACITY: 12' X 3/4" BOILER DUTY
12' X 5/8" PIPE DUTY
ROLL DIAMETER: 15"
LENGTH OF ROLLS: 12'2"
AIR DROP END
MOTORS: 30 HP MAIN DRIVE
15 HP REAR ROLL ADJUSTMENT
(2) 2 HP WEDGE ADJUSTMENT
NOTE - THIS PLATE ROLL WAS NOT USED IN
PRODUCTION WORK, ONLY MAINTENANCE WORK.
NEW ELECTRICS INCLUDING JOYSTICK CONTROL,
MOTOR BRAKE, AND MAGNETICS WERE UPDATED
BY BERTSCH IN 1994.
>From Maintenance Shop, very little use.
12' x 1/2" Webb Model 9L Mechanical: 12' x 1/2" Webb Model 9L Mechanical
OVERHAULED 1996
Specifications:
Capacity - 1/2" x 12' MS
Length Of Roll - 146"
Roll Diameter - 13"
Rolling Speed - 7-14 FPM
Motors - 20 & 10 HP
Equipped With:
REAR POWER ADJUSTING ROLL
AIR DROP END
3/8" x 120" Hydraulic Plate Bending Roll: 3/8" x 120" Hydraulic Plate Bending Roll
Specifications:
Hydraulic Initial Pinch Plate Rolls
Equipped With:
HYDRAULIC DROP END
REMOTE PEDISTAL MOUNTED CONTROL
hyd. roll adjustment
IN PLANT
2004 Eagle BA-35 Tube Bender: Eagle BA-35 Full Featured
Hydraulic
Computer rolled ring bending machine
variable speed rotation
3.5" floppy drive
1" and 1 1/2" Square set of dies and 1 1 3/8" round die that are made of nylon for soft materials
* All machinery specifications must be independently verified by buyer. All machinery sales are subject to prior sale. Any agreement to purchase or sell machinery must be in writing.
Full Machine Specifications
PC Based Control
Industrial PC with 3.5" Floppy Drive
Unlimitied Storage Capacity
Three Driven Shafts for Driving of the Profile
Oil Bath Speed Reducer
Variable Rotation Speed
Hydraulic Powered Forming Roll
Hydraulic Power Unit
Dual Lateral Material Guide, four way adjustable
Vertical and Horizontal Operating Positions with Rests on
Remote Pulpit with Push Buttons
Heavy Duty Foot Pedals & Emergency Stop
Digital display
Operating & Maintenance Manuals
Key Switch Security Lockout
RS 232 Serial Port
"Automatic Interpolation" Software
"Auto Motor Image" Capability
"Graphic Imaging"
1" and 1 1/2" Square set of dies and 1 1 3/8" round die that are made of nylon for soft materials
We found 12 matching ads. Now displaying the remaining 12 ads.
USED BUFFALO NO. 2-1/2 UNIVERSAL IRONWORKER: USED BUFFALO NO. 2-1/2 UNIVERSAL IRONWORKER
RAM PUNCH PRESSURE: 105 TONS
STROKES PER MINUTE: 44
DEPTH OF THROAT: 24"
SHEAR: 8" X 7/8" FLATS
3/4" PLATE
14" LENGTH OF KNIVES
24-1/4" WORK HEIGHT
PUNCH: 1-3/16" X 7/8"
1" X 1"
38-3/4" WORK HEIGHT
BAR CUTTER: 6" X 6" X 1/2" ANGLES 90 DEGREES
4" X 4" X 1/2" ANGLES 45 DEGREES
2-1/4" ROUNDS
2" SQUARES
45-3/8" WORK HEIGHT
BUILT IN 90 DEGREE NOTCHER ON PUNCH HEAD:
3" X 7/16" ANGLES
7/16" PLATE
3-1/4" DEPTH OF CUT
54-1/2" WORK HEIGHT
BUILT IN SQUARE COPER ON SHEAR END:
4" X 1/2" ANGLES
1/2" PLATE
2-1/4" WIDTH OF CUT
3-1/2" DEPTH OF CUT
48-1/4" WORK HEIGHT
ONE-SHOT LUBRICATION
MOTOR: 7-1/2 HP 1760 RPM
50 Ton Hydraulic Ironworker Piranha Model P-50: (1) Piranha 50 ton Hydraulic Ironworker
Throat depth - 8"
Open height - 13-1/2"
Closed height w/o die block - 9-1/4"
Stroke length - 4-1/4"
Punch capacity - 50 tons
... material thickness - 13/16" through 3/4"
... strokes per minute - 60 @ 1/2"
... platen table size - 10" x 17"
Bar shear capacity, round - 1/4" to 1-1/2"
Bar shear capacity, square - 1/2" to 1"
Coper-notcher (56 tons) - 2-3/4" x 4" x 1/4"
Plate shear (14-5/8") - 3/4" x 10" , 5/8" x 14"
Angle shear, maximum - 5" x 5" x 3/8"
Brake: 8" long
Hydraulic pump (10.5 GPM) - 2600 PSI, 18 gallons
Motor - 10 HP, 1800 RPM--
Includes Punch Dies & Press Brake Die (4-Way die ranging from approx 1" wide to 2-1/2" wide)
50 Ton Hydraulic Ironworker Piranha Model P3: Piranha Model P-3 50 Ton Hydraulic Ironworker
Angle Shear Cap (L1): 5 "
Angle Shear Cap (L2): 5 "
Angle Shear Cap (T): .375 "
Tonnage: 50 Ton
Coper/Notcher: 2-3/4" x 4" x 1/4"
Power: 10 HP
Throat: 8 "
50 Ton Hydraulic Ironworker Piranha Model P-50: Used P-50 PIRANHA 5"x 5"x 3/8" - 50 Ton Hydraulic Ironworker
General Specifications:
Tonnage Capacity At Punch End: 50
Throat Depth: 8"
Closed Height w/o Die Block: 9-1/4"
Bar Shear; Round Min. to Max. 1/4" to 1-1/2"
Square Min. to Max. 1/2" to 1"
Punch End; Max. Material 13/16" thru 3/4"
Max. Hole (special tool) 5" thru 1/8"
Platen Table Size: 10" D x 17" W
Bending Attachment: 8"
Strokes Per Minute: 60 at 1/2"
Open Height: 4-1/4"
Standard Motor: 10 HP AC
Coper-Notcher; (Mat) 2-3/4" x 4"x 1/4"
Plate Shear; 15" Long
3/4"x 10"
5/8"x 15"
Angle Shear; 5"x 5"x 3/8" w/Special Tool: 4"x 4"x 1/2"
Equipped With:
Automatic Urethane Hold Down on Punch Stripper & On Angle Plate & Bar Shear
Front 5 Position Joy Stick
Electric Limit Switches To Set Stroke Control When Using Foot Pedal
Foot Pedal Controls
Standard Knives
Coper-Notcher Station
Assorted Punch & Dies
Optional Quick Set Punch Gauging Table
Optional Mechanical Back Gauge
Optional 8" (Press Brake Type) Bending Attachment
Pipe Notching Attachment
Integral Lifting Lug
Replacement Cost NEW Today Including Cost Of Options Approximately $15,400. At Quoted Price, We Will Off Limited 6 Month Guarantee From Factory Rep.
70 Ton Mechanical Ironworker Peddinghaus Model 210A/16: Specifications:
Capacity 70 Tons
Punch Capacity1-1/16” in ¾” or 7/8” in 7/8”
Angle Capacity5” x 5” x ½” @ 90 deg
Flat4-3/8” x 1” or 11” x 3/8”
Notcher 9/16”
Speed45 SPM
65 Ton Hydraulic Ironworker Scotchman Model 6509: Specifications:
65 Ton Punch Station (1-16" Dia x 3/4" Thick) reference
9" Throat
Shear Capacity:1" X 6",3/4" X 10",3/8" X 16",1/4" X 24"
Electrics: 5HP Hyd Motor
Equipped With:
24" Flat Bar Shear With 4-Way Reversible Blade
Optional Accessories:
Angle Shear Capacity At 90 Degree: 6" x 6" x 3/8"
Rod Shear: Round 1/4" to 1-1/4", 9 Cavities
Square 1/4" to 1", 1 Cavity
24" Brake Attachment, 2" Opening
Dies & Punches
50 Ton Hydraulic Ironworker Edwards Model Jaws IV: Specifications:
Punch Capacity - 1" hole in 5/8" Plate
Shear Capacity - 10" x 1/2"
Round Capacity - 1"
Square Capacity - 1"
Angle - 3" x 3" x 3/8"
Coper - 2" x 3" x 5/16"
3 HP Main Motor
40 Ton Scotchman 4014C Ironworker : GENERAL SPECIFICATIONS
Punching Capacity: 40 Ton
Punching Capacity: 1" in 1/2"
Throat Depth: 6"
Flat Bar Shear Length: 14"
Bar Shear Capacity: 5/8" x 5"
Strokes Per Minute, Light Material: 40
Strokes Per Minute, Max. Capacity: 12
EQUIPPED WITH
3 HP Motor
Adjustable Stroke Controls
30 Ton STRIPPIT SUPER 30 Fabricator: 30 Ton STRIPPIT SUPER 30 Fabricator
Capacity 30 Ton
Throat depth 30”
Max. hole diameter 3 ½” Dia. x 12 ga.
Max. Material thickness 1”-1/4”
Sheet size 30” x 30”
Gauging with stops 30” x 30”
Stroke length 5/8”
Speed 165 HPM
Table adjustment 2 ¼”
EQUIPPED WITH:
Hand operated duplicator attachment
Nibbling attachment
1 ¼” and 3 ½” punch holders
2-Axes DRC digital readouts
Adjustable table height
(2) Cabinets with large quantity of tooling
1 H.P. 3/60/220-440 Volt Motor and controls
We found 1 matching ad. Now displaying the final ad.
WYSONG Motorized headstock and tailstock welding positioner set: WYSONG Motorized headstock and tailstock welding positioner set
Approx. weight capacity 10,000 lbs.
Table diameter 60”
Max. height table center to floor 43”
EQUIPPED WITH:
Tailstock has roller wheels for track movement for length adjustment between faceplates
Headstock and tailstock mounted with 60” diameter T-slotted faceplates
3 H.P. Baldor 3/60/230-460 volt main drive with gear box, FVR G7S
AC inverter drive and variable speed control with disconnect box
Remote foot pedal control
18’L tracks for tailstock
We found 21 matching ads. Now displaying the remaining 21 ads.
75 Ton NIAGARA Model AF- 4 ½ O.B.I. Flywheel press with air clutch: 75 Ton NIAGARA Model AF- 4 ½ O.B.I. Flywheel press with air clutch
Rating of press 75 Tons
Safe capacity near bottom of stroke 90 tons
Diameter of shaft at main and connection bearings 4 ½”-6 ¾”
Stroke 4”
Variable speeds 60 to 120 SPM
Ram adjustment 3 3/8”
Throat depth 12 ½”
Slide area 15” x17 1/8”
Distance between gibs 13 ¼”
Bed area 36” x 24”
Rectangular opening in bed 18” x 14”
Width of opening in back 20”
Shut height 15 ¾”
EQUIPPED WITH:
Electro-pneumatic friction clutch and brake
Flywheel design
Bolster plate
Air Counter balance of ram
Dual palm controls
7 ½ H.P. 3/60/220-440 variable speed drive w/ controls
125 Ton No.10 FEDERAL O.B.I. Flywheel Press: 125 Ton No.10 FEDERAL O.B.I. Flywheel Press
Tonnage, capacity near bottom of stroke 125 Tons
Stroke 4”
Adjustment of slide 2 ½”
Round punch shank hole 2 ½”
Face area 30”LR x 14”FB
Bed area 40”LR x 28”FB
Shut height 17 ½”
Throat depth 15”
Opening in bed 18” x 14”
Opening through back 18”
Crankshaft dia. at main bearings 5 ¾”
Diameter at crank bearing 7”
Speed 120 SPM
EQUIPPED WITH:
Flywheel construction
Air clutch and brake
3” thick bolster plate
Dual palm button controls
Lincoln CentroMatic Lubrication
Knock-out bar
Single or continuous stroke
15 H.P. 3/60/230-440 Volt Motor
with controls
500 TON HPM 4-POST HYDRAULIC PRESS: 500 TON HPM 4-POST HYDRAULIC PRESS:
FAST TRAVERSE MODEL - HOUSING TYPE
CAPACITY .......................... 500 TONS
TIE ROD DIAMETER .................. 6´´
AREA OF BED ....................... 36´´ X 24´´
AREA OF RAM ....................... 36´´ X 24´´
DIAMETER OF RAM ................... 22´´
DAYLIGHT .......................... 32´´
STROKE ............................ 24´´
SIZE OF WINDOWS ................... 18´´
NO PIT REQUIRED
SPEEDS ... 80 IPM ADVANCE
... 56 IPM PRESSING
... 860 IPM RETURN
HPM HYDRAULIC PUMP ................ 900 RPM - MODEL 3120-50B-RB50 GPM @ 2500 PSI
100 HORSEPOWER MAIN MOTOR
60 TON P H HYDRAULIC C FRAME PRESS: 60 TON P H HYDRAULIC C FRAME PRESS:
CAPACITY ..................... 60 TON
STROKE ....................... 20´´
DAYLIGHT ..................... 33-1/2´´
CLOSED HEIGHT ................ 13-1/2´´
BED AREA (T-SLOTTED) ......... 30´´ X 27´´
RAM AREA ..................... 30´´ X 14´´
GUIDED RAM ................... YES
FLOOR TO BED ................. 32´´
HYDRAULIC MOTOR .............. 25 HORSEPOWER
150 TON LEMPCO MODEL #EH150 HYDRAULIC H-FRAME PRESS: 150 TON LEMPCO MODEL #EH150 HYDRAULIC H-FRAME PRESS:
CAPACITY .......................... 150 TONS
STROKE ............................ 12´´
DIAMETER CYLINDER ROD ............. 3-1/2´´
RAM SPEEDS PRESS .................. 18 IPM
RAM SPEEDS RETURN ................. 12 IPM
USABLE BED AREA ................... 48´´ X 19´´
DISTANCE BETWEEN FRAME HOUSINGS ... 48´´ X 9-1/2´´
RAM HEAD TRAVEL, LEFT TO RIGHT .... 30´´
HAND CRANK ADJUSTABLE BED HEIGHT
TOP MOUNTED HYDRAULICS
10 HORSEPOWER HYDRAULIC MOTOR
PACIFIC 750 TON 500OBL12 PRESS: PACIFIC 750 TON 500OBL12 PRESS
CYBELEC PC 90/9000 CONTROL
750 TON MAX
This press has computer-controlled dual hydraulic 150 ton cushions in bed. We also have a full set of large filler blocks for the ram with T- slots machined in the ram, the bed, and the bottom of the filler bocks. The computer has the capability of holding draw-formed part setting for the cushions and the ram in memory so they can be repeated.
Current Speeds: RA: 360 ipm
FP: 132 ipm
NP: 5-36 ipm ( Variable )
FR: 198 ipm
SR: 66 ipm
Open Height: 60"
Stroke: 24"
Window dimension: 50" x 19"
Bed size: 179" x 72"
75 Ton DAKE Elec-Draulic II DAKE Acting H-frame press, type 8-075: 75 Ton DAKE Elec-Draulic II DAKE Acting H-frame press, type 8-075
Capacity press 75 Tons
Capacity pull 28 Tons
Ram speed:
Pressing 5 I.P.M.
Return 15 I.P.M.
Vertical travel of table 30”
Vertical travel of ram 10”
Width between uprights 44”
Width between table channels 8 ¼”
Max. distance, ram to table 37-5/8”
EQUIPPED WITH:
Variable ram speed with pressure sensitive throttling type 4-way valve
Double acting cylinder providing for lifting force as well as pressing force
Adjustable table
Pressure gauge
Flat ram nose for pressing
(2) "V" blocks
2 H.P. 3/50/230-460 volt hydraulic pump motor and electrical controls
40 Ton 40-W ROCKFORD Flywheel O.B.I Press Model 40-W: 40 Ton 40-W ROCKFORD Flywheel O.B.I Press Model 40-W
Capacity: 40 tons
Crankshaft diameter at main bearings: 3 3/8"
Crankshaft diameter at crankpin: 4 1/2"
Distance, bed to gibs 14 1/2"
Stroke: 3"
Ram adjustment: 3"
Shut height to bed: 10 3/4"
Slide shank hole 2" dia. x 2 3/4" depth
Frame inclining angles: 13º, 26º, 40º
Speed: 100 SPM
Bed area: 14 1/2" x 26"
Slide face area: 81/2" x 17"
EQUIPPED WITH:
Air clutch and brake
Weldotron sentry control
Flywheel construction
Motorized inclining mechanism
Dual palms
Remote electric foot pedal
Production counter
Bed bolster
Lincoln centro-matic automatic lub.system
3 H.P. 3/60/440 Volt motor w/controls
Overall height: 93"
We found 10 matching ads. Now displaying the remaining 10 ads.
Miller Plazcut/Zipcut hand held plasma cutter: Input:
200/230 Volt
Single Phase
Amp 60/52
60HZ
Air Pressure 73
Output:
143 Volts
40 Amp
Duty Cycle 40%
Max. OCV 270
200 AMP Koike Aronson D80 Hypertherm HT2000 Plasma Cutter: 40-200 Amp Output
9' x 30' Air Table
2 Axis Hybrid D80 Control
CNC Control needs work
Cutting Capacity of 2" thick mild steel edge start
Pierce Capacity of 1-1/2" thick mild steel
Production Cutting Capacity of 1" thick mild steel piercing
Remote High Frequency Control
Remote Current Control
Gas Console
LINDE PLASMA/FLAME CUTTING SYSTEM: LINDE PLASMA/FLAME CUTTING SYSTEM
AREA OF WATER TABLE ................... 114´´ X 108´´
CENTER DISTANCE BETWEEN RAIL .......... 11'4´´
CUTTING WIDTH ......................... 111´´
CONTROL MODEL ......................... LINDE #UCNC-8
WATER TABLE MFG ......................ANDERSON ENGINEERING
NUMBER OF LINDE PLASMA UNITS: ......... 2
TYPE .................................. 200-3
P/N ................................... #677740
SERIAL ................................ #X85C-14687 & #F85K-50166
PLASMA CONTROL ........................ #PCC-8
LINDE POWER SUPPLIES .................. 2
TYPE .................................. PLASMARC #PHC-601
P/N ................................... #677330
SERIAL ................................ #F85K-50165
INPUT ................................. 380/415/460 VOLT - 50/60 CYCLE
OUTPUT ................................ 420 VCU MAX. - 250 VOLT - 600 AMP
60" x 120" Prima Rapido 5-axis laser: Prima Rapido 5-axis laser
Chiller
2200W PRC resonator rebuilt 4 years ago by PRC of New
Jersey. Very reliable machine. 62,000 total hours on
resonator since 1996.
Table size is 60” by 120” in Flat cutting mode – also cuts in 3D
mode (5 Axis). Cuts up to ¼” thickness steel.
1996 Omax 2652 26" x 52" Water Jet Cutter: 26" x 52" Cutting Area
2004 Meyer P-2040 20 hp 42k psi Bare Shaft Pump (1500 Hrs)
PC Based CNTL
New Maxjet 5 Cut. Head
Hi/Low Bypass Valve
2004 Omax Sofware Installed
VIDEO AVAILABLE UPON REQUEST
* All machinery specifications must be independently verified by buyer. All machinery sales are subject to prior sale. Any agreement to purchase or sell machinery must be in writing.
Full Machine Specifications
Cutting Area: 26" x 52"
Pump: 2004 Meyers P-2040 Bare Shaft Crank Case & Pump
20hp, 42,000 psi
New Charge Pump
New Hi/Low Pressure Bi-Pas Valve Recently Added
New MaxJet 5 Abrasive Cutting Head
All Software Updated by Omax in '04
PC Based Control
Programmable Z-Axis
HOURS: Approximately 2,000 Hours
Video Available Upon Request
2002 Calypso 6' x 12' Water Jet Cutter: Calypso Shark
6'x12'
Dual Abrasive Cutting Head
55k psi
100h.p. Pump
EBBCO Polishing System
* All machinery specifications must be independently verified by buyer. All machinery sales are subject to prior sale. Any agreement to purchase or sell machinery must be in writing.
Full Machine Specifications
Work Envelope 6' x 12'
Dual Abrasive Cutting Head Option
EBBCO Closed Loop Polishing System # CLS-141
Thermal Care AccuChiller
Stand Alone Control Unit with PC & Monitor
WS100 High Pressure Waterjet Pumping System
Design Pressure: 60,000 PSI
Max. Operating Pressure: 55,000 PSI
Flow: 2 GPM
Motor: 100HP
Motor Speed: 1800 RPM @ 60HZ
Intensifier Cycle Rate: 20Cycles/Minute @ Max. Flow Rate
12’x 24’ MG CNC Plasma/Oxygen track type Burning Machine with table: 12’x 24’ MG CNC Plasma/Oxygen track type Burning Machine with table
Max. burning width 12’
Max. burning length 24’
EQUIPPED WITH:
(1)Oxygen torch with motorized lifter
(1)Plasma torch with motorized lifter
153 x 24’ water table w/ pump system
Burny 3 CNC control with cassette
*Note Machine is less Plasma power supply
We found 2 matching ads. Now displaying the remaining 2 ads.
Uniloy 5500 4 Head Blowmolder: Uniloy 5500
(4) Head
8" Head Center Spacing
3" Extruder
Cooling Bed
Leak Detector
Part Pick Off Unit
Includes 1/2 Gal. & One Gal. Unilot Molds
1991 Van Dorn 300-HT Injection Molder: 1991 Van Dorn 300-HT Injection Molder
Platen Size 37" x 37"
Distance Between Tie Rods 25" x 25"
Injection Pressure 23,264 PSI
Max Open Daylight 49"
Ejector Stroke 6"
Pump Motor 50 HP
EL Control
HKO
CP
Tonnage: 300.0
Shot Size: 20
2000 Hwa Chin HC450CL Injection Molder: 2000 Hwa Chin HC450CL Injection Molder
Distance Between Tie Bars 30.5" x 30.5"
(2) Machines Available Located In Mexico City
Tonnage: 450.0
Shot Size: 46
2000 Hwa Chin HC600CL Injection Molder: 2000 Hwa Chin HC600CL Injection Molder
Distance Between Tie Bars 34.5" x 34.5"
Located In Mexico City
Tonnage: 600.0
Shot Size: 70
Battenfeld Fischer VK-6 Blow molder: Battenfeld Fischer VK-6 Blow molder
(4) Head
100 mm Head centers
90 mm Extruder
Maco 6000
Making 24 oz. PE Bottles
Many Upgrades
8 oz bottles to 1/2 gallon bottles
1984 Hayssen 115200 CD 1000 Blow Molder: 1984 Hayssen 115200 CD 1000 Blow Molder
Dual Head
2.50 # Shot Capacity
90mm Extruder
200 hp
Moog 20pt.
Liberty (2) Lane Cooling Bed
(1) Liberty Trimming Station
(1) Leak Detector
Producing 4.2 Gallon Cooking Oil Containers
Set up for 5 Gallon Containers
Engel, ES 700-200, 200 Ton, Injection Molding Machine: Platen 30.71" x 27.36"
Tie Bars 21.26" x 18.11"
Clamp Stroke 18.11"
Min/Max Mold Height 5.91"/22.05"
Max Daylight 40.16"
Stroke 5.91"
CC 90 Control
HKO
CP
RI
Ton: 200.0
Shot Size: 18.0
JSW, J200EII-SP, 200 Ton, Injection Molding Machine: Distance Between Tie Bars 20.1" x 20.1"
Platen Size 29.5" x 29.5"
Max Daylight Opening 40.94"
Opening Stroke (Max) 17.3"
Ejector Force x Stroke 4.84" x 5.12"
Min Mold Size (H x V) 11.8" x 11.8"
Syscom Controller
HKO
Ton: 200.0
Shot Size: 3.7
1992 Cincinnati VT300-16 Injection Molder: Tie Bar Spacing 25.2" x 24.6"
Platens 36.8" x 36.2"
Clamp Toggle
Clamp Stroke 22.8"
Daylight Max/Min 48"/7.9"
Mold HT MAx/Min 25.2"/7.9"
Camac VCL Control
HKO
Air Blow
CP
RI
Tonnage: 300.0
Shot Size: 16
* All machinery specifications must be independently verified by buyer. All machinery sales are subject to prior sale. Any agreement to purchase or sell machinery must be in writing.
Full Machine Specifications
Tonnage 300 Ton
Shot Size 16 oz
Tie Bar Spacing 25.2" x 24.6"
Platens 36.8" x 36.2"
Clamp Toggle
Clamp Stroke 22.8"
Daylight Max/Min 48"/7.9"
Mold HT Max/Min 25.2"/7.9"
Equipped With
Camac VLC Control
HKO, Air Blow
CP, RI
1993 Toyo TM300G2 Injection Molder: Distance Between Tie Bars 28.74" x 28.74"
Platen Size 37" x 37"
Clamping Stroke 22.83"
MoldHeight (Min/Max) 9.84"/25.60"
Ejector Stroke 5.51"
Voltage 460
PLCS 6 Control
CP
Tonnage: 300.0
Shot Size: 32.8
* All machinery specifications must be independently verified by buyer. All machinery sales are subject to prior sale. Any agreement to purchase or sell machinery must be in writing.
Full Machine Specifications
Tonnage 300 Ton
Shot Size 32.8 oz
Distance Between Tie Bars 28.74" x 28.74"
Platen Size 37" x 37"
Clamping Stroke 22.83"
Mold Height (Min/Max) 9.84"/25.60"
Ejector Stroke 5.51"
Voltage 460
Equipped With
PLCS-6 Control
CP
2001 Husky H-225-RS-40 Injection Molder: Tie Bar spacing 26" x 26"
Platen 37.4" x 37.4"
Daylight 47.2"
Min/Max Mold Height 11"/26"
PSI 23,496
Polaris Control
Stripper Plate Air
Invision System Interface
SPC/SQC
High Speed Package
Tonnage: 225.0
Shot Size: 7.3
* All machinery specifications must be independently verified by buyer. All machinery sales are subject to prior sale. Any agreement to purchase or sell machinery must be in writing.
Full Machine Specifications
Tonnage 225 Ton
Shot Size 7.3 oz
Tie Bar Spacing 26" x 26"
Platen 37.4" x 37.4"
Daylight 47.2"
Min/Max Mold Height 11"/26"
PSI 23,496
Equipped With
Polaris Control
Stripper Plate Air
Invision System Interface
SPC/SQC
High Speed Package
1998 Husky GL-225/RS50 Injection Molder: Tie Bar Spacing 24.4" x 24.4"
Platen SIze 35.7" x 36.5"
Ejector Stroke 5.9"
Daylight (Max) 57.1"
Shut Height (Min/Max) 16.7"/30.5"
Clamp Stroke 26.6"
Siemens Control
Air Blow
Excessive Cycle time (if shot is not made)
Accumulators
Special Shut Height (see above specs)
SPC.SQC
Tonnage: 250.0
Shot Size: 10
* All machinery specifications must be independently verified by buyer. All machinery sales are subject to prior sale. Any agreement to purchase or sell machinery must be in writing.
Full Machine Specifications
Two (2) 1998 250 Ton, 10 oz. HUSKY GL-225/RS50
Tonnage 250 Ton
Shot Size 10 oz
Tie Bar Spacing 24.4" x 24.4"
Platen Size 35.7" x 36.5"
Ejector Stroke 5.9"
Daylight (Max) 57.1"
Shutheight (Min/Max) 16.7"/30.5"
Clamp Stroke 26.6"
Equipped With
Siemens Control
Air Blow
Excessive Cycle time (if shot is not made)
Accumulators
Special Shut Height (see above specs)
SPC/SQC
1997/96 Toyo Plastar TM-200H Injection Molders: Distance Between Tie Bars 22.05" x 22.05"
Platen Size 30.71" x 30.71"
Clamp Stroke 18.54"
Mold Height (Min/Mx) 7.87"/19.69"
Ejector Stroke 4.72"
Electrics 460 Volt
PLCS-9 Color Touch Panel Control
HKO< CP
Tonnage: 200.0
Shot Size: 11
* All machinery specifications must be independently verified by buyer. All machinery sales are subject to prior sale. Any agreement to purchase or sell machinery must be in writing.
Full Machine Specifications
Two (2) 1996/97 200 Ton, 13.1 oz. Toyo Plastar
Capacity Tonnage 200 Ton
Shot Size 11/13.01
Distance Between Tie Bars 22.05" x 22.05"
Platen Size 30.71" x 30.71"
Clamp Stroke 18.54"
Mold Height (Min/Max) 7.87"/19.69"
Ejector Stroke 4.72"
Electrics 460 Volt
Equipped With PLCS-9 Color Touch Panel Control
HKO
CP
1997 $39,500.00
1996 $36,500.00
1995 Nissei FS160S36ASE Injection Molder: Tie Bar Spacing
18 1/8" x 18 1/8"
Platen Size 26.75" x 26.75"
Screw Diameter 50MM "B" Size
Clamp Stroke 18.5"
Daylight Max 26.4"
Min Mold Height 16.1"
Ejector Stroke 3.9"
Electrics 460 Volt
NC9000G Cntrl
HKO
Air Eject
CP
RS 232 Port
Ref No:
Tonnage: 177.0
Shot Size: 11.8
* All machinery specifications must be independently verified by buyer. All machinery sales are subject to prior sale. Any agreement to purchase or sell machinery must be in writing.
Full Machine Specifications
Tonnage 177 Tons
Shot Size 11.8 oz
Tie Bar Spacing 18-1/8" x 18- 1/8"
Platen Size 26.75" x 26.75"
Screw Diameter 50 MM "B" Size
Clamp Stroke 18.5"
Daylight Max 26.4"
Min Mold Height 16.1"
Ejector Stroke 3.9"
Electrics 460 Volt
Equipped With:
NC9000G Control
HKO
Air Eject
CP
RS 232 Port
2001 Toyo SI-300 Injection Molder: Platen Size 37" x 37"
Distance Between Tie Bars 28.74" x 28.74"
Clamp Stroke 22.3"
Max Mold Height 23.62"
Max Daylight 46.45"
Min Mold Height 9.84"
PLCS 9 Control
21,000 Hours
Tonnage: 300.0
Shot Size: 32.8
* All machinery specifications must be independently verified by buyer. All machinery sales are subject to prior sale. Any agreement to purchase or sell machinery must be in writing.
Full Machine Specifications
Tonnage 300 Ton
Shot Size 32.8 oz
Platen Size 37" x 37"
Distance Between Tie Bars 28.74" x 28.74"
Clamp Stroke 22.83"
Max Mold Height 23.62"
Max Daylight 46.45"
Min Mold Height 9.84"
Equipped With
PLCS 9 Control
21,000 Hours
1999 Husky GL-300RS70/60 Injection Molder: Tie Bar Spacing
28.3" x 28.3"
Platen Size 40.8" x 41.9"
Ejector Stroke 5.9"
Daylight (Max) 64.9"
Clamp Stroke 30.5"
Clamp Shut Height (Min/Max) 16.7"/34.4"
Siemens Control
SPC/SQC Package Safety Drop Bar
200MM Machine Risers Full SPI Pattern
1 Hyd Function on Moving Platen SPI Robot Interface
High Torque Screw Drive Special Paint (Ibsen Ivory)
2 Air Circuts (High & Low Pressure) Excessive Cycle Time Seq
In Mold Ejection Software
Tonnage: 330.0
Shot Size: 28
* All machinery specifications must be independently verified by buyer. All machinery sales are subject to prior sale. Any agreement to purchase or sell machinery must be in writing.
Full Machine Specifications
Tonnage 330 Ton
Shot Size 28 oz
Tie Bar Spacing 28.3" x 28.3"
Platen Size 40.8" x 41.9"
Ejector Stroke 5.9"
Daylight (Max) 64.9"
Clamp stroke 30.5"
Clamp Shut Height (Min/Max) 16.7"/34.4"
Equipped With
Siemens Control
SPC/SQC Package Safety Drop Bar
200MM Machine Risers Full SPI Pattern
1 Hyd Function on Moving Platen SPI Robot Interface
High Torque Screw Drive Special Paint (Ibsen Ivory)
2 Air Circuts (High & Low Pressure) Excessive Cycle Time Seq
In Mold Ejection Software
2000 Nissei FN-6000 Injection Molder: Tie Bar Spacing 26" x 26"
Daylight 45.3"
Clamp STroke 32.7"
Mold Thickness 12.6"
NC9300 T Control
HKO
RI
Tonnage: 308.0
Shot Size: 6.7
* All machinery specifications must be independently verified by buyer. All machinery sales are subject to prior sale. Any agreement to purchase or sell machinery must be in writing.
Full Machine Specifications
Tonnage 308 Ton
Shot Size 6.7 oz
Tie Bar Spacing 26" x 26"
Daylight 45.3"
Clamp Stroke 32.7"
Mold Thickness 12.6"
Equipped With
NC 9300T Control
HKO
RI
1997/96 Cincinnati VT440-54 Injection Molders: Tie Bar Spacing 58.9" x 28.9"
Platen 39.4" x 39.4"
Clamp Toggle
Clamp Stroke 25.6"
Daylight max/Min 53.15"/9.84"
Mold Height Max/Min 27.56" x 9.84"
VSX Control
RI
Air Blow
Tonnage: 440.0
Shot Size: 54
* All machinery specifications must be independently verified by buyer. All machinery sales are subject to prior sale. Any agreement to purchase or sell machinery must be in writing.
Full Machine Specifications
Two (2) 1997/96 440 Ton, 54 oz. Cincinnati VT440-54
Tonnage 440 Ton
Shot Size 54 oz
Tie Bar Spacing 28.9" x 28.9"
Platen 39.4" x 39.4"
Clamp Toggle
Clamp Stroke 25.6"
Daylight Max/Min 53.15"/9.84"
Mold Height Max/Min 27.56" x 9.84"
Equipped With
VSX Control
RI
Air Blow
Prices 1997-$69,500.00/1996-$62,500.00
2004 Negri-Bossi VE-300-1700 Injection Molder: Screw Diameter 2.364"
Max Clamp Stroke 23.64"
Min/Max Mold Height 9.85"/27.58"
Ejector Stroke 8.86"
Platen Dimensions 37.03" H x 34.67" V
Tie Bar Spacing 24.82" H x 22.45" V
HKO
SPI Robot Interface
Tonnage: 330.0
Shot Size: 26.82
* All machinery specifications must be independently verified by buyer. All machinery sales are subject to prior sale. Any agreement to purchase or sell machinery must be in writing.
Full Machine Specifications
Two (2) 2004 330 Ton, 26.82 oz. NEGRI-BOSSI VE-300-1700
Tonnage 330 US Tons
Shot Size 26.82"
Screw Diameter 2.364" (60mm)
Max Clamp Stroke 23.64"
Min / Max Mold Height 9.85" / 27.58"
Ejector Stroke 8.86"
Platen Dimensions 37.03"H x 34.67" V
Tie Bar Spacing 24.82" H 22.45" V
Equipped With:
Hydraulic Core Pull
SPI Robot Interface
1999 Husky GL-300RS50/42 Injection Molder: Tie Bar Spacing 28.3" x 28.3"
Platen Size 40.8" x 41.9"
Ejector Stroke 5.9"
Daylight (Max) 64.9"
Clamp Stroke 30.5"
Clamp Shut Height Min/Max) 16.7"/34.4"
Siemens Control
SPC/SQC Package Safety Drop Bar
200MM Machine Risers Full SPI Pattern
1 Hyd Function on Moving Platen SPI Robot Interface
High Torque Screw Drive Special Paint (Ibsen Ivory)
2 Air Circuts (High & Low Pressure) Excessive Cycle
Time Seq In Mold Ejection Software
MSI Controller Interface Visual Monitoring System
Tonnage: 330.0
Shot Size: 10.1
* All machinery specifications must be independently verified by buyer. All machinery sales are subject to prior sale. Any agreement to purchase or sell machinery must be in writing.
Full Machine Specifications
One (1) 1999 330 Ton, 10.1 oz. HUSKY GL-300RS50/42
Tonnage 330 Ton
Shot Size 10.1 oz
Tie Bar Spacing 28.3" x 28.3"
Platen Size 40.8" x 41.9"
Ejector Stroke 5.9"
Daylight (Max) 64.9"
Clamp stroke 30.5"
Clamp Shut Height (Min/Max) 16.7"/34.4"
Equipped With
Siemens Control
SPC/SQC Package Safety Drop Bar
200MM Machine Risers Full SPI Pattern
1 Hyd Function on Moving Platen SPI Robot Interface
High Torque Screw Drive Special Paint (Ibsen Ivory)
2 Air Circuts (High & Low Pressure) Excessive Cycle Time Seq
In Mold Ejection Software
MSI Controller Interface Visual Monitoring System
2004 Negri-Bossi VE-370-H2300 Injection Molder: Screw Diameter 2.75"
Max Clamp sTroke 27.9"
Min/Max Mold Height 11.82"/29.55"
Ejector Stroke 10.8"
Platen Dimensions 42.15" x 39"
Tie Bar Spacing 27.97" x 24.82"
HKO
SPI Robot Interface
Tonnage: 407.0
Shot Size: 37.4
* All machinery specifications must be independently verified by buyer. All machinery sales are subject to prior sale. Any agreement to purchase or sell machinery must be in writing.
Full Machine Specifications
One (1) 2004 407 Ton, 37.4 oz. NEGRI-BOSSI VE-370-H2300
Capacity 407 US Tons
Shot Size 37.4 oz
Screw Diameter 2.75" (70mm)
Max Clamp Stroke 27.9"
Min/ Max Mold Height 11.82" / 29.55"
Ejector Stroke 10.8"
Platen Dimensions 42.15" H x 39" V
Tie Bar Spacing 27.97" H x 24.82" V
Equipped With:
Hydraulic Core Pull
SPI Robot Interface
1997 Cincinnati VT440-54 Injection Molder: Tie Bar Spacing 28.9" x 28.9"
Platen 39.4" x 39.4"
Tie Bar Spacing 28.9" x 28.9"
Clamp Toggle
Clamp Stroke 25.6"
Daylight Max/Min 53.15"/9.84"
Mold Height Max/Min 27.56' x 9.84"
VSX Control
HKO
CP
32,887 Hours
Tonnage: 440.0
Shot Size: 54
* All machinery specifications must be independently verified by buyer. All machinery sales are subject to prior sale. Any agreement to purchase or sell machinery must be in writing.
Full Machine Specifications
Tonnage 440 Ton
Shot Size 54 oz
Tie Bar Spacing 28.9" x 28.9"
Platen 39.4" x 39.4"
Clamp Toggle
Clamp Stroke 25.6"
Daylight Max/Min 53.15"/9.84"
Equipped With
VSX Control
HKO
CP
32,887 Hours
1995 Toshiba ISG-950-81B Injection Molder: Tie Bar Spacing 41.7" x 41.7"
Platen 60.2" x 60.2"
Min/Max Daylight 19.7"/88.5"
Clamp Stroke 68.9"
Injectvisor S10 Control
Dual CP
Motion no Motion
Air Blow
Tonnage: 950.0
Shot Size: 183
* All machinery specifications must be independently verified by buyer. All machinery sales are subject to prior sale. Any agreement to purchase or sell machinery must be in writing.
Full Machine Specifications
Tonnage 950 Tons
Shot Size 183 oz
Tie Bar Spacing 41.7" x 41.7"
Platen Size 60.2" x 60.2"
Min/Max Daylight 19.7" / 88.5"
Clamp Stroke 68.9"
Equipped With:
Injectvisor S10 Control
Dual Core Pull
Motion No Motion
Air Blow
Uniloy Model 350R2 Blow Molders: Package Available
Includes (2) Machines
(1) Gallon Molds
Foremost Blending System
(2) 70 Ton Chillers
Head Tooling
* All machinery specifications must be independently verified by buyer. All machinery sales are subject to prior sale. Any agreement to purchase or sell machinery must be in writing.
Full Machine Specifications
Two (2) Uniloy Model 350R2 Machines Available
Includes Support Equipment & Molds
Machines (2) Uniloy Dairy Blow Molders
Model 350R2
Number Of Heads 4
Head Center Spacing 8"
Screw Size 3.5"
L/D Ratio 24:1
Clamp Tonnage 90 Tons
Controls PLC
ONE UNIT IS UNDER POWER / 2ND MACHINE
NEW DRIVE
MACHINE PRICES: $95,000.00 / $85,000.00
Includes (8) Dairy Gallon Molds $35,000.00 for PKG.
New Foremost Blending System $41,000.00
2 - 70 Ton Air Cooled Chillers $14,500.00 EA.
New Head Tooling $8500.00
PACKAGE PRICE $285,000.00
Photos Available
2003 NFM Twin Screw Compounding Extruder: 20mm
54:1 L/D Ration
10 HP
5 Electrical Barrel Heater Zones
"46 Hours of use"
* All machinery specifications must be independently verified by buyer. All machinery sales are subject to prior sale. Any agreement to purchase or sell machinery must be in writing.
Full Machine Specifications
Screw Size 20 mm
L/D Ratio 54:1
Vented or Non (may be plugged) Vented
Heated Electrical Heated Barrel
Heater Barrel Zones 5
Horsepower 10 @ 500 rpms
Control Cabinet Attached on Stand
Ammeters
Electrics 460v / 3 ph / 60 hz
Includes Vacuum System-New water ring vacuum pump
1.5 HP Motor
Pump
Vacuum Gage, Flow Meter, & adjusting Valve
Rated @ 15 cfm @ 27" Hg
Flow - 0.9 gpm
Electrical 230v / 3 ph / 60hz
Water Requirement For Exchange Cooling 5 GPM
1996 Van Dorn 500HP80F Injection Molder: Platen Dimension 47" x 47"
Tie Bar Spacing 32.5" x 32.5"
Ejector Stroke 6"
Clamp Stroke 38"
Daylight Max 68" w/Ejector Stroke Plate Removed
Min Mold Height 12
Pathfinder 4500 Control
CP
Motion no Motion
Robot Interface
Tonnage: 500.0
Shot Size: 80
* All machinery specifications must be independently verified by buyer. All machinery sales are subject to prior sale. Any agreement to purchase or sell machinery must be in writing.
Full Machine Specifications
Capacity Tonnage 500 Tons
Shot Size 80 oz
Platen Dimensions 47" x 47"
Tie Bar Spacing 32.5" x 32.5"
Ejector Stroke 6"
Clamp Stroke 38"
Daylight Max 68" w/Ejector Plate Removed
Min Mold Height 12
Equipped With Pathfinder 4500 Control
CP
Motion no Motion
Robot Interface
1995 Van Dorn 700 HP 125F Injection Molder: Tie BAr Spacing 36.5" x 36.5"
Max Clamp Stroke 44"
Max Daylight 72.75"
Platen Size 62" x 53.5"
Ejector Stroke 10.82"
Pathfinder 4500 Control
CP
Two Stage Air Eject
SPI Robot Interface
Motion/No motion
Conair HARMO Robot Modle HIM-400SWK
35,500 Run Hours
!!VIDEO AVAILALBE!!
Tonnage: 700.0
Shot Size: 125
* All machinery specifications must be independently verified by buyer. All machinery sales are subject to prior sale. Any agreement to purchase or sell machinery must be in writing.
Full Machine Specifications
Two (2) 1995 700 Ton, 125 oz. VAN DORN 700-HP-125F
Tonnage 700 Tons
Shot Size 125 oz
Tie Bar Spacing 36.5" x 36.5"
Max Clamp Stroke 44"
Max Daylight 72.75"
Platen Size 62" x 53.5"
Ejector Stroke 10.82"
Equipped With:
Pathfinder 4500 Control
Core Pull
Two Stage Air Eject
SPI Robot Interface
Motion / No Motion Option
Conair HARMO Robot Model HIM-400SWK
Hours: 35,500 Run Hours
!!! VIDEO AVAILABLE !!!
1998 Van Dorn 1000 HP 80 Injection Molder: Distance Between Tie Bars 44" x 44"
Platen Size 65" x 65"
Open Daylight Max 74"
Clamp Stoke Max 50"
Pathfinder 3000 Cotnrol
HKO
CP
RI
Premium Filtration
Machine can be upgraded to 260 oz
Tonnage: 1000.0
Shot Size: 80
* All machinery specifications must be independently verified by buyer. All machinery sales are subject to prior sale. Any agreement to purchase or sell machinery must be in writing.
Full Machine Specifications
Capacity Tonnage 1000 Ton
Shot Size 80 oz
Distance Between Tie Bars 44" x 44"
Platen Size 65" x 65"
Open Daylight Max 74"
Clamp Stroke Max 50"
Equipped With
Pathfinder 3000 Control
HKO
CP
RI
Premium Filtration
Machine can be upgraded to 260 oz
1999 Van Dorn 700HP4300 Wide Platen Injection Molder: Platen DImensions 62" x 53.5"
Distance between Tie Rods (H) 45" x 36.5"
Max Clamp Stroke 44"
Max Open Daylight 72.75" W/Eject Pl. Removed
Min Mold Height 16"
Ejector Stroke 6"
Pathfinder 5000 Control
Wide Platen and Extended Tie Bar Space
Dual CP
Motion no Motion
Robot Interface
Feed Throat Temperature Cotnrol
HKO
Cavity Pressure Control
Heat Sensors
Pump Lockout
Breather Bags
Tonnage: 700.0
Shot Size: 89.6
* All machinery specifications must be independently verified by buyer. All machinery sales are subject to prior sale. Any agreement to purchase or sell machinery must be in writing.
Full Machine Specifications
One (1) 1999 700 Ton, 89.6 oz. VAN DORN WIDE PLATEN 700HP4300
Tonnage 700 Ton
Shot Size 89.6 oz
Platen Dimensions 62" x 53.5"
Distance Between Tie Rods (H) 45" x 36.5"
Max Clamp Stroke 44"
Max Open Daylight 72.75" W/Eject Pl. Removed
Min Mold Height 16"
Ejector Stroke 6"
Equipped With
Pathfinder 5000 Control
Wide Platen & Extended Tie Bar Space
Dual CP
Motion No Motion
Robot Interface
Feed Throat Theperature Control
HKO
Cavity Pressure Control
Heat Sensors
Pump Lockout
Breather Bags
1993 Cincinnati VT-440-68 Injection Molder: Tie Bar Spacing 28.9" x 28.9"
Platen 39.4" x 39.4"
Clamp Toggle
Clamp Stroke 25.6"
Daylight Max/Min 53.15"/9.84"
Mold Height Max/Min 27.56"/9.84"
Camac VEL Control
HKO
CP
RI
Air Blow
Tonnage: 440.0
Shot Size: 68
* All machinery specifications must be independently verified by buyer. All machinery sales are subject to prior sale. Any agreement to purchase or sell machinery must be in writing.
Full Machine Specifications
Tonnage 440 Ton
Shot Size 68 oz
Tie Bar Spacing 28.9" x 28.9"
Platen 39.4" x 39.4"
Clamp Toggle
Clamp Stroke 25.6"
Daylight Max/Min 53.15"/9.84"
Mold Height Max/Min 27.56" x 9.84"
Equipped With
Camac VEL Control
HKO, CP, RI
Air Blow
1985 Cumberland 37H-85GRAN 5KN Granulator with blower: 18" x 37"
2 Bed Knives
15 Blade Helical Hog
7/16" Screen
Soft Start
150 Horsepower
Includes Blower
Cyclone
* All machinery specifications must be independently verified by buyer. All machinery sales are subject to prior sale. Any agreement to purchase or sell machinery must be in writing.
Full Machine Specifications
Feed Throat Opening 18" x 37"
Number Of Rotor Knives 15 Blade Helical Hog
Number Of Bed Knives 2
Screen Size 7/16" dia.
Cutting Circle Diameter 16"
Horsepower 150
Soft Start Yes
Blower, Cyclone & Conveyor Included 15 HP Blower
Electrics 480v
Throughput 3000 lbs./HR.
Photos available
1993 Herbold MS 60/60 6060H7-3 Granulator: 1993 herbold Granulator
SMS 6060H7-3
Refurb. 2006
23" x 28" Throat Size Opening
125 HP
Blower
Cyclone
Soft Start
* All machinery specifications must be independently verified by buyer. All machinery sales are subject to prior sale. Any agreement to purchase or sell machinery must be in writing.
Full Machine Specifications
REFURBISHED 2006
Style - Open Rotor Configuration
Throat Size Opening 23" x 28"
Knives 7 Knife Open Rotor
(Optional Blocks can be installed to create solid rotor)
Horsepower 125
Screen Size 2 3/8"
Blower Horsepower 5
Includes:
Cyclone and Stand
Details Re: Refurb Motor Inspected (new bearings installed)
New Main Rotor Bearings
New Fly & Bed Knives and bolts
6" Quick Connect galvanized pipe to connect to cyclone
Motor starter contactor for 125 hp motor
Machine usage PVC Pipe - Hopper is designed to hold long pieces of -
pipe, but could be modified to be shorter
Photos available
1995 Cincinnati VT-725-116 Injection Molder: Distance Between Tie Bar 38.19" x 38.19"
Platen Size 56.5" x 60.3"
Max Daylight 78.7"
Min/Max Mold 11"/39.4"
Camac 486 Control
Single CP
Air Blow
Tonnage: 725.0
Shot Size: 116
* All machinery specifications must be independently verified by buyer. All machinery sales are subject to prior sale. Any agreement to purchase or sell machinery must be in writing.
Full Machine Specifications
Capacity: Tonnage 725 Ton
Shot Size 116 oz
Distance Between Tie Bar 38.19" x 38.19"
Platen Size 56.5" x 60.3"
Max Daylight 78.7"
Min/Max Mold 11"/39.4"
Equipped With: Camac 486 Control
Single Core Pull
Air Blow
Cumberland Granulator: Cumberland Granulator
Throat Size 24" x 18"
Bed Knives 2
Rotor Knives 3
HP 75
Air Flow 137 CHM
* All machinery specifications must be independently verified by buyer. All machinery sales are subject to prior sale. Any agreement to purchase or sell machinery must be in writing.
Full Machine Specifications
Granulator # 1 Cumberland Open Rotor
Throat Size Opening 24" x 18"
Rotor Knives 3
Bed Knives 2
Rotor & Bed Knives 28"
Horsepower 75
Filter System Design Pressure 20 HG.
30 Sqaure Feet Cloth Filter
Air Flow 137 CHM
5 3/4" 60 lb bags
Holding Silo 45" x 32" High
Positive Displacement Blower 5 hp Sutorbilt (brand)
Conveyor 13' L x 20" Wide
Silo Acuator Premier Pneumatics 15"
Photos available
1995 Van Dorn 1000 HP 165F-ELP Injection Molder: Platen 73" x 65"
Tie Bar Distance 52" x 44"
Clamp Style Hydraulic
Daylight Min/Max 12"/74"
Ejector Stroke 8"
Motors (2) @ 100 HP
Pathfinder 2500 Control
Wide Platen
CP
Motion no Motion
Robot Interface
Mold Ejector
Tonnage: 1000.0
Shot Size: 165
* All machinery specifications must be independently verified by buyer. All machinery sales are subject to prior sale. Any agreement to purchase or sell machinery must be in writing.
Full Machine Specifications
Tonnage 1000 Ton
Shot Size 165 oz
Platen 73" x 65"
Tie Bar Distance 52" x 44"
Clamp Style Hydraulic
Daylight Min/Max 12"/74"
Ejector Stroke 8"
Motors (2) @ 100 HP
Equipped With
Pathfinder 2500 Control
Wide Platen
CP
Motion no Motion
Robot Interface
Mold Ejector
1995 Cincinnati VT725-140 Injection Molder: Distance Between tie Bars 38.19" x 38.19"
Platen Size 56.5" x 60.3"
Max Daylight 78.7"
Min/Max Mold 11"/39.4"
Camac VSX Control
Motion no Motion
CP
Air Blow
Tonnage: 725.0
Shot Size: 140
* All machinery specifications must be independently verified by buyer. All machinery sales are subject to prior sale. Any agreement to purchase or sell machinery must be in writing.
Full Machine Specifications
Tonnage 725 Ton
Shot Size 140 oz
Distance Between Tie Bars 38.19" x 38.19"
Platen Size 56.5" x 60.3"
Max Delight 78.7"
Min/Max Mold 11"/39.4"
Equiped With
Camac VSX Control
Motion no Motion
CP
Air Blow
Davis Standard Thermatic 350II-F6251 Extruder: Davis Standard Thermatic 350 II-F6251
Single Screw Extruder
Screw Size 3.5" L/D Ratio 24:1
Barrel Zones 5
Cooled Air
HP 75
Includes Control Panel
* All machinery specifications must be independently verified by buyer. All machinery sales are subject to prior sale. Any agreement to purchase or sell machinery must be in writing.
Full Machine Specifications
Single Screw Extruder
Screw Size 3.5"
L/D Ratio 24:1
Barrel Zones 5
Cooled Air
Horsepower 75Includes Control Panel
Photos available
NRM Pacemaker 70 Model Blown Film Extruder: NRM Pacemaker 70
3.5" 24:1 L/D Ratio
14" Rotational Bubble Extrusion Die
Refurb. Line
Complete System with tower
* All machinery specifications must be independently verified by buyer. All machinery sales are subject to prior sale. Any agreement to purchase or sell machinery must be in writing.
Full Machine Specifications
COMPLETE BLOWN FILM
Extruder Screw Size 3.5"
L/D Ratio 24:1
Barrel Zones 5
Controls Barber Coleman 520
Includes 1998 Maguire Model 4 Compartment wt. scale
Blender with MPI Digital Scale System 50# Hopper
1996 Alpha Marathon Model M48-14DL
14" Rotational Bubble Extrusion Die w/ bubble gas -
Cage Stabilizer
New York Blow Company
20 HP Blowe System
Custom Mfg. 68" Primary Nip assembly
1985 Reifenhauser Mdl. WF1600
Max Width 1600 mm
Slitter / Winder with 5 splitting heads
Quick Draft 3 hp trim removal blower system
***** INCLUDES ENTIRE TOWER ASSEMBLY
Photos available
1982 Sterling Blow Molder: Dual Heads
10 # Shot Capacity
32” x 62” Platen
4.5” Extruder
Maco Controls
* All machinery specifications must be independently verified by buyer. All machinery sales are subject to prior sale. Any agreement to purchase or sell machinery must be in writing.
Full Machine Specifications
Accumulator Blow Molder
Number Of Heads 2
Shot Size Capacity (lbs) 10
Head Centerline Distance 24"
Extruder Screw Size 4.5"
L/D Ratio 24:1
Approximate Output 750 lbs/hour
Drive HP 150 hp/DC Drive
Hydraulic Unit Horsepower 60
Platen Size 32" x 62"
Clamp Tonnage (US Tonnage) 75
Daylight 46.5"
Plate Thickness 4"
Guide Rods 5"
Controls Maco
Base Width 9'
Base Length 23'
Base Height 7.5'
Head tools 6"
Photos available
1993 Sterling Blow Molder: Dual Head
15# Shot Capacity
32" Centerline
4.5" Extruder
60" x 81" Platen
Maco Controls
* All machinery specifications must be independently verified by buyer. All machinery sales are subject to prior sale. Any agreement to purchase or sell machinery must be in writing.
Full Machine Specifications
Accumulator Style Blow Molder
# Of Heads 2
Head Shot Capacity (lbs) 15
Head Centerline 32"
Extruder Screw Size 4.5"
L/D Ratio 24:1
Horsepower 150 DC Drive
Approximate Output 900 lbs./hr.
Hydraulic Unit HP 40
Platen Size 60" x 81"
Clamp Tonnage (US Tonnage) 180
Daylight 66"
Platen Thickness 4.75"
Guide Rods 6"
Controls Maco
Base Width 10'
Base Length 21' 6"
Base Heitght 11'
Head Tooling 8"
Photos available
1992 Nissei Model ASB 650 EXIID Blow Molder: One Step PET bottle machine
(does perform & blow molding)
Dual 84 mm extruders
Omron Controls
* All machinery specifications must be independently verified by buyer. All machinery sales are subject to prior sale. Any agreement to purchase or sell machinery must be in writing.
Full Machine Specifications
One Step PET Bottle Machine
Extruders Dual Extruders
Extruder Screw Sizes 84 mm
Clamp Tonnage 100 tons
Heater & Timer Controls Omron
Current Mold Set Up - (8) 32 ounce, 50 mm neck -
juice containers
Includes Bottle Stand up equipment, 10" wide REX chain -
conveyor
All manuals & maintenance records
Spare parts
Machine has also ran the following bottles:
8 oz. - 24 mm neck, up to 1 gallon - 120 mm neck
Photos available
Under power
1988 Magic Model MG-L5/D Blow Molder: Recently Rblt
Single Head
100 mm Screw
20:1 L/D
HDPE
with (2) Single Cavity 4 Liter Molds
* All machinery specifications must be independently verified by buyer. All machinery sales are subject to prior sale. Any agreement to purchase or sell machinery must be in writing.
Full Machine Specifications
Head(s) Single head with curved neck mounted on single flange. Single Channel/Head
Mechanical weight adjustmant
Extruder Screw Size 100 mm
L/D Raio 20:1
Screw Type HDPE
Brushless AC Motor & Digital Inverter
(includes access ladder and hand rail on extruder -
platform)
Knife Pneamatically operated cold knife for parison cutting
Deflashing (3) Station deflashing system
Material Handling Horizontal Scrap Conveyors
Incline Scrap Conveyor to granulator
Gravimetric Weigh Blender to mix virgin, color & regrind Maguire, WSB-100 Series
Vacuum Loading System - (4) loaders to convey scrap- Wittmann
virgin, and colorant to blender
High Speed single head leak tester
Tooling Includes (2) single 4 liter bottle Molds
Photos available
Under power
1995 Cincinnati E75-D-25 Blow Molder: Dual Head
2.5 # Shot Capacity
3" Extruder
26" H x 39" V Platen
Camac 486
* All machinery specifications must be independently verified by buyer. All machinery sales are subject to prior sale. Any agreement to purchase or sell machinery must be in writing.
Full Machine Specifications
Accumulator Head Blow Molder
Number Heads 2
Shot Size Capacity 2.5 lbs
Clamp Force 50 Ton
Distance Between Tie bars 26" H x 39" V
Max Open Daylight 35-40"
Min. Daylight Closed 15-20"
Shut Height Adjustment 5"
Clamp Stroke 20"
ExtruderScrew Size 3"
L/D Ratio 24:1
Standard output in HDPE 375 lbs/hr
Side mounted part takeaway unit
Hydraulic Servo Controlled Tooling
Stripper Air Operated
Needle Blow Circuits
Prepinch softward
Controls Camac 486
Electrics - 460v / 3 / 125 - 31.5 - 90 amps
Jomar Model 85 Blow Molder: Jomar 85 Injection Blow Molding Machine
* All machinery specifications must be independently verified by buyer. All machinery sales are subject to prior sale. Any agreement to purchase or sell machinery must be in writing.
Full Machine Specifications
Injection Blow Machine
Preform Clamp Force 72.1 Tons
Blow Clamp Force 17 Tons
Shut Height 10"
Press Stroke 5"
Extruder Screw Size 2.5"
L/D Ratio 24:1
Maximum Shot Capacity (PVC) 225 grams
Horsepower 75
Trigger Bar Size 21"
Photos available
1991 Bekum 602D Blow Molder: "Only 15000 Hours"
Single Head
4 x 85 mm Head Size
85 mm Centerline
3 x 60 mm Extruder
40 HP
Platen 740 mm x 440 mm
Maco 6
* All machinery specifications must be independently verified by buyer. All machinery sales are subject to prior sale. Any agreement to purchase or sell machinery must be in writing.
Full Machine Specifications
Number Of Heads 1
Head Size 4 x 85 mm
Head Centerline 85 mm
Extruder Screw Size 3 x 60 mm
Extruder Ratio 24:1
Screw Type Pineapple Mixer
Gear Box s-633-s
Gear Box Ratio 2.17:1
Drive HP 30 / Power tec
Hydraulic Unit HP (Lincoln) 40 hp main / 5 hp aux.
Platen Size 470 mm x 440 mm
Tonnage 11.2
Daylight 220 mm
Platen Thickness 3 1/8" Front
Controls Maco 6
Run Hours 15225
Photos available
1983/84 Battenfeld Fischer FHB 054-1 Continous Extrusion Blow Molders: 1983/84 (2) Battenfield Fischer, Mdl. 054-1
Single Head(s)
125 mm Head Centerline
60mm/90mm Extruder
19:1 / 24:1
40/60 HP
250 mm x 400 mm Platen
Maco 6 Controls
VERY CLEAN!
* All machinery specifications must be independently verified by buyer. All machinery sales are subject to prior sale. Any agreement to purchase or sell machinery must be in writing.
Full Machine Specifications
Two (2) 1983/84 Battenfeld Fischer FHB 054-1
1983 UnitNumber Of Heads 1
Head Centerline 125 mm
Extruder Size 90 mm
L/D Ratio 19:1
Screw Type Pineapple mixer
Horsepower 60
Platen Size 250 mm x 400 mm
Controls Maco 6
1984 Unit Number Of Heads 1
Head Centerline 125 mm
Head Size Single Parison
Extruder Size 80 mm
L/D Ratio 24:1
Screw Type Pineapple mixer
Horsepower 40
Platen Size 360 mm x 510 mm
Controls Maco
Photos available
1984 Battenfeld FHB 106-1 Continous Extrustion Blowmolder: 1984 Battenfield Fischer Mdl. FHB 106-1
Single Head
(5) Parison
Head Centerline 70 MM
Extruder size 80 MM
24:1 L/D
360 mm x 510 mm Platen Size
Controls Maco 6
VERY CLEAN & UNDER POWER!
* All machinery specifications must be independently verified by buyer. All machinery sales are subject to prior sale. Any agreement to purchase or sell machinery must be in writing.
Full Machine Specifications
Continous Extrustion Blowmolder
Number Of Heads 1
Head Size 5 Parison
Head Centerline 70 mm
Extruder Size 80 mm
Extruder Ratio 24:1
Screw Type Pineapple Mixer
Drive HP 60
Hyd. Unit HP 7.5
Platen Size 360 mm x 510 mm
Controls Maco 6
Photos available
We found 5 matching ads. Now displaying the remaining 5 ads.
Model 3219 SkyJack Scissor Lift: Model 3219 SkyJack Scissor Lift:
Model Year 1996
Platform Height 19'-0"
Working Height 25'-0"
Stowed Height 79"
Overall Width 32.5"
Overall Length 68"
Platform Size 27.5" x 64"
Roll Out Deck 3'-0"
Non- Marking Tires
New Batteries Less than 2 years old.
New Control Arm.
New spare Control Arm Never Used.
10 Ton LE TOURNEAU Electric Under-hung Hoist, Series 10TE 1245: 10 Ton LE TOURNEAU Electric Under-hung Hoist, Series 10TE 1245
Capacity 10 Ton
Lift 31’
EQUIPPED WITH:
Manual trolley
We found 9 matching ads. Now displaying the remaining 9 ads.
Blast Cabinet: 400CFM 1/2HP Motor
Dust Collector
1-Side Doors 31-1/2" x 33-5/8"
1 Fill Door
Safety Foot Control
Glove Arm Holes
Viewing Window 12" x 20"
2 Tube 24" Flourescent Light
We found 17 matching ads. Now displaying the remaining 17 ads.
2002 Shoda Essetre Leonardo: 2002 Shoda Essetre Leonardo
(4) Axis Cnc Router Working Center
60" x 120" Bed
Single Spindle
18 hp @ 14,000 rpm
Tool
Tool Changer
Compressor
Dust collector
Pod & Rail System
Hand Held Controls
COMPLETE SYSTEM
: 55” TIMESAVER High Powered Single Drum Sander, Model 5521HPL
Width of belt 55”
Diameter of steel drum 11 ½”
Belt speed 7300 SFPM
Variable speed range of billing roll 20-60 FPM
EQUIPPED WITH:
Single steel drum design
Variable speed billing roll feed
Automatic pneumatic belt traking
Trabon automatic lub. system
Motor load meter
In-feed and out-feed pinch rolls
Free standing control cabinet
Extra sanding belts
5 H.P. Billing roll drive
150 H.P. 3/60/460 Volt drive
with braking
48” x 48” x 20’ ROCKFORD Hydraulic Openside Planer: 48” x 48” x 20’ ROCKFORD Hydraulic Openside Planer
Table size: 44” x 20’
Maximum cutting width 62”
Maximum distance under cross rail 48”
Table cutting speed range 0 to 100 FPM
Equipped with:
(2) Swivel heads on rail
(1) R.H. side head
Hydraulic tool lifters
40 H.P. 3/60/440 volt hydraulic drive unit
2000 Thermwood 40 3 Axis CNC Router: (3) Axis
60" x 60" Single Table
10.5" Z Travel
91000 Super Controller
Approx 2000 Hours
Full Machine Specifications
Number Of Axis 3
Number Of Tables Single
Table Size 60" x 60"
Spindle Horsepower 10
Brushless AC Servo Drive Feed Rate of 1500
Feed Rate Override
Feed Hold
"Z" - Axis Travel 10.5"
Controls 91000 Supercontroller
6.4 Gigabyte Hardrive
EIA 274D Programming
Includes Automatic Tool Length Sensing
Hand Held Programmer
Unit is Set Up for Vacuum
THE MACHINE HAS APPROXIMATE 2000 HOURS
2005 Liberty CNC Routers 3 Axis: 2005 Liberty CNC Router Table Size 24" x 42"
Single Table
Number of Spindles 1
Equipped with Vexta Control
Full Machine Specifications
3 Axis CNC Router For Small Parts
# Of Axis 3
Table Size 24" x 42"
Single Table
Table Hold Down(s) "T" Slots
Number Of Spindles 1
Z - Axis Travel 1"
Horsepower .05
Controls Vexta
Includes Engraver Head
1981 PDA P/C 50 3 Axis CNC Router: (3) Aixs Router
21.13" x 24.13" Table Size
2.0" Z Axis Travel
Vacuum Table
Quick Change
(2) HP
Tool Holders
Turbo Cam Control
Full Machine Specifications
Number Of Axis 3
Table Size 22" x 24"
Table has Patented vacuum scavenge/brush hold-down system. (does not include vacuum pump)
Y- Axis Travel 24.13"
X - Axis Travel 21.13"
Z - Axis Travel 2.0"
Number Of spindles Single
Horsepower 2 @ 24,000 rpm
Max Spindle Speed 400 IPM
Quick Change Tool Holders for 1/8" shank tools, 3/8-Collet Capacity
Phenolic Tooling Plate
Cutter Radius Compensation
Nested Subroutines for step and repeat functions
Tooling and programming macros for test coupon- fabrication
1.2 MB, 3.5" micro floppy disc
Menu Driven or EIA RS-274-D programming
Controls TurboCam
Electrics 230/460 vac, 20/10 amps
MACHINE HAS BEEN RURFURBISHED AND HAS -
"0" HOURS OF USE
1998 Techno Model HX33VBM4896010 3 Axis CNC Router: Full Machine Specifications
# Of Axis 3
Table 48" x 96"
# Of Spindles Single
Horsepower 5
Motor Make Colombo
(includes an extra 3 axis 5.5 hp Perske motor)
X-Axis Travel 96"
Y-Axis Travel 60"
Z-Axis Travel 18.7"
Controls Computer Base Controls
2000 Northwood Model NW-265MC1D1 Dual Table 3 Axis CNC Router: (2000) Northwood Model NW-265MC1D1
Dual 6' x 5' Table
(3) Axis
Tool Holder
14.0" Z-Axis
17.4 HP
GE Fanuc Controls
Full Machine Specifications
"UNDER A 1000 HOURS OF USE!"
Number Of Axis 3
Number Of Tables 2
Table Size 72" x 60"
Axes Travel/Speed X - Axis: 200.00"
Rapid Traverse Rate 0 to 2500" / Min.
Y - Axis: 68.0" Rapid Traverse Rate 0 to 2500" / Min.
V - Axis: 68.0" Rapid Traverse Rate 0 to 2500" / Min.
Z - Axis: 14.0" Rapid Traverse Rate 0 to 500" / Min.
Cutting Feed Rate X - Axis 1200" / Min
Y - Axis 1200" / Min
V - Axis 1200" / Min
Z - Axis 500" / Min
C-Axis 360 Degrees
Distance Between Tables 2"
Main Shank Size 1" Maximum
Collets (4) 1/4" ER-40
(4) 1/2" ER-40
(4) 3/4" ER-40
Tool Holders (12) HSK-63F Collet Chuck (RH)
Tooling Length (extended from tool holder) 4" Maximum
Cutter Diameter 4.5"
Main Spindle Power 17.4 HP (13 kw)
Spindle Speed 3600 - 18000 rpm
Shank Size (Boring Unit) 10 mm (10H7)
Boring Unit Power 2.5 hp
Boring Unit Speed 4000 rpm
Controls GE/Fanuc 160i-MA
Controls Includes Advanced Preview Control (APC)
MPG Handle, RS-232C/PCMCIA interfaces, 32k memory
(4 wire grounded)
SUPER CLEAN
1995 Multicam 48 CNC Router: Spindle
48" x 96" Table
T-Lock Hold Downs
5 HP Perske Motor
PLC/Software
Vacuum System
(2) Xtra Perske Heads
Full Machine Specifications
Number Of Axis 3
Number Of Tables 1
Table Size 48" x 96"
Table Hold Down "T" Lock Material Hold down
Number Of Spindles Single
Spindle Motor Perske 5 HP Spindle
Drive Stepper Motor
Accuracy (max speed) +/- .002/ft 4" second
Maximum Weight 800 lbs.
Controls PLC
Software includes CASmate scan / 3-D
Import / Export clean up
In/outline / router offsets. Hatch and island fill for engraving. Full Scanning and line conversion capabilities with 3-D machine tool path generation for interactive "z" control on the fly
Includes (2) Extra Perske Motor Heads
1.5 HP Vacuum Pump for product hold down
Computer / Software
Monitor, HP Scanjet 3P & Printer
48” x 48” x 20’ ROCKFORD Hydraulic Openside Planer: 48” x 48” x 20’ ROCKFORD Hydraulic Openside Planer
Table size: 44” x 20’
Maximum cutting width 62”
Maximum distance under cross rail 48”
Table cutting speed range 0 to 100 FPM
Equipped with:
(2) Swivel heads on rail
(1) R.H. side head
Hydraulic tool lifters
40 H.P. 3/60/440 volt hydraulic drive unit
You can use the navigation bar below to jump to other groups of 75 results for each section out of your total of 617 hits from all database sections.