Year |
Make |
Model |
Condition |
Price |
Details |
|
Ad # 12092 | Heavy Duty Large Lathe 24in. & over swing |
|
Leblond |
12" x 36" Engine Lathe |
|
sold |
Photo /
More Info. |
: Leblond 12" x 36" engine lathe, S/N 7C2351
|
|
Ad # 10097 | Heavy Duty Large Lathe 24in. & over swing |
2007 |
GMC |
GT-26120 |
Excellent |
Sold |
Photo /
More Info. |
26 x 120"centers: 26"swing over ways, 34"gap,
4"spindle bore,
120"between centers.
Comes with taper attatchment, tool post, 2-steady rests, follower rest, live center, dead center, 3&4 jaw chucks, large faceplate, DRO, and thread dial.
Std. Factory specs below-please verify actual machine
• Ajustable Spindle Clutch: Forward, Reverse, Stop
• Heavy Cast Iron Base
• Foot Brake
• Coolant System
• Work Light
• Taper Turning Attachment
• Larger Spindle bore: 4-1/8"
• Larger Motor: 15 HP, 220v or 440volts, 3 phase
• Rapid Traverse
• ISO 9002 certified factory
• Fully enclosed precision gearbox
• Heavy duty spindle D1-8
• Heavy duty guideway width 15-1/2"
• 12 speeds: 36 - 1600 rpm
• 27 kinds of inch threads, and 22 metric threads
• Threading and feed rate change without changing gears out
• Spindle is balanced, hardened and precision ground
• Spindle is supported at 3-points by high precision bearings
• All gears and shafts are hardened and precision ground
• Guideways induction hardened and precision ground
• Automatic lubrication system, headstock and feed box
Specifications:
• Maximum swing over cross slide: 16-1/2"
• Max swing in gap: 34-1/4"
• 65 kinds of Longitudinal feeds; 0.0023 - 0.093 I.P.R.
• 65 kinds of cross feeds; 0.0011 - 0.04 I.P.R.
• Inch threads: 2 to 28 T.P.I., 27 kinds
• Metric threads: 1 - 14mm I.P.R., 22 kinds
• Module threads: 0.5 - 7mm, 18 kinds
• Diametral pitch threads: 4 - 56 DP, 24 kinds
• Spindle taper: MT6
• Tailstock taper: MT5
• Toolpost size: 1" square
• Max travel of top slide: 5-3/4"
• Max travel of cross slide: 14"
• Max weight of workpiece: 2000 Lbs
• Machine Net Weight:
GT26120: 9500 Lbs
Standard Equipment
• Foot Brake
• Coolant System
• Work Light
• Cast Iron Base
• Taper turning attachment
• Rapid traverse
• Auto carriage stop
• Oil pump on apron
• Adjustable spindle clutch
• Inch/metric dials
• 12" 3- jaw chuck with set reversible jaws
• 20" 4-jaw chuck with reversible jaws
• 25" face plate
• 10" drive plate
• 10-1/4" steady rest
• 3" follow rest
• Removable gap
• 4-way tool post
• Full length splash guard
• (2) dead centers
• Reducing sleeve
• Thread chasing dial
• Tool box
Optional Equipment:Included
• Digital Readout
3/"-5" spare steady rest
Live center
5PC carbide tooling turning set |
|
Ad # 13288 | Heavy Duty Large Lathe 24in. & over swing |
1985 |
Poreba |
TZG-250 A |
Excellent |
sold |
Photo /
More Info. |
3200mm: Poreba Heavy Plate T-Type Lathe
Model : TZG-250 A
Year: Approx. 1985
Technical Specifications:
Height of Centers above bed base: mm: 1300
Max. Turning Diameter : mm: 3200
Length of throat: mm: 650
Max. Weight of workpiece fixed in faceplate: kg:
6000
Max. Spindle torque at speed 0.5-1.7 rmp: kgm:
6300
24 spindle speeds within range: rpm: 0.5-100
Diameter of chuck plate
Rapid travel of headstock: mm/min: 800
Main drive motor power: kW: 55
20 Longitudinal feeds of saddle: mm/rev: 0.18-
5.06
81 Metric thread: mm/min: 1-192
95 Inch threads: rev/turn: 30-1/8
Overall Dimensions: mm: 5520 X 5180 X 2650
Weight: kg: 30,000 Approx.
|
|
Ad # 15374 | Heavy Duty Large Lathe 24in. & over swing |
1959 |
AXELSON |
2516 D |
Excellent |
sold |
Photo /
More Info. |
28'' X 120''REBUILT : AXELSON 28'' X 120'' (20 HP) NEWALL 2-AXIS DRO: REBUILD IN 2010 AXELSON LATHE MODEL 2516-D 20HP 28'' X 120'' NEWALL 2-AXIS ... |
|
Ad # 14009 | Heavy Duty Large Lathe 24in. & over swing |
1992 &89 |
Weipert / Weiler |
W1003/6 |
Excellent |
sold |
Photo /
More Info. |
Roll Lathes:40" swing x 19'5"ft centers: 1992 & 1989 Ferdinand C. WEIPERT/Weiler:
Precission Roll Turning Lathes
Model:W1003/6
Capacity:40"swing over
bed,26.6"over crossslide
Center distance:19'5"ft or 6 meters
between centers
spindle bore:4.5"
main motor: 30HP upgraded to brushless DC
motors in 200? for less maint and accuracy
spindle RPM:4-900RPM infi-variable
Spindle nose:DIN #55022 standard Size 11
workpiece weight:9,900 max without
supports
18"-4jaw chuck in headstock-DIN#55022
size11nose
follower rest:14" max dia with each
machine
has metric hand dials on crosslide &
carriage
DRO-digital readout display mounted on
cross slide in/out of tool only-english or metric
display rapid traverse on carriage:vari-spindle
speed control using reastat:4.4-900 M/min
tailstock:heavy duty with hyd.acc
Includes:12" 4-jaw chuck in tailstock
3 tool holders included-each machine
includes all manuals/drawings
Notes:Equipped with special:vari speed
drives on both spindle and carrage traverse for
accurata adjustable fine finishing of part using
infi-variable speeds/feeds
Note:No threading capability on machines
Note:(2)-Identical machines available
1989 & 1992 the 1989 is 380/3 voltage but includes
a
transformer to up voltage to 460/3 other
is 460/3
Note:These machine have been very well
maintained on a routine schedule, also includes
many spare parts such as: motor brushes, belts,
headstock & other bearings and more. Also leveling
pad feet"fixators"are included for 1 machine only
not both.
These are a very high quality German made
heavy duty precision lathe used to cut
large
heavy printing rolls currently will hold
at least +-0.002" end to end of cut length full
travel 20'
|
|
Ad # 14355 | Heavy Duty Large Lathe 24in. & over swing |
|
Lelbond |
32" |
Excellent |
sold |
Photo /
More Info. |
32 x 204" lathe: LEBLOND 32" x 204" Lathe
32" chuck w/4 independent jaws,
2 steady rests,
25 H.P. Motor
Max rpm: 255
24.5' long overall |
|
Ad # 13788 | Heavy Duty Large Lathe 24in. & over swing |
|
axelson |
|
Excellent |
sold |
Photo /
More Info. |
32" X 432": AXELSON 32" X 432" LATHE s/n: 1715
32" swing
34.5" max swing
42' bed
432" centers
25 hp motor
28" chuck
4 steady rests
Tailstock
MACHINE IS CURRENTLY DISMANTLED INTO 2 PIECES
STEADY RESTS AND CHUCK HAVE BEEN REMOVED AND
SKIDDED |
|
Ad # 10359 | Heavy Duty Large Lathe 24in. & over swing |
1975 |
Meuser |
M6B |
Excellent |
sold |
No Photo /
More Info. |
66" Swing X 32'(384"): 66" Swing, 48" SOCS, X 384", 400 rpm, 60hp. 56" 4 Jaw Chuck, (2) Steady Res... |
|
Ad # 15374 | Heavy Duty Large Lathe 24in. & over swing |
1959 |
AXELSON |
2516 D |
Excellent |
sold |
Photo /
More Info. |
28'' X 120''REBUILT : AXELSON 28'' X 120'' (20 HP) NEWALL 2-AXIS DRO: REBUILD IN 2010 AXELSON LATHE MODEL 2516-D 20HP 28'' X 120'' NEWALL 2-AXIS ... |
|
Ad # 13925 | Heavy Duty Large Lathe 24in. & over swing |
1950's ? |
Lodge and Shipley |
? |
Fair |
sold |
Photo /
More Info. |
36" Swing, 20 feet between centers: Lodge & Shipley Lathe
Capacity: 20ft. between centers, 36" Swing
Electrical: 110/Single Phase
HP: 2 |
|
Ad # 16178 | Heavy Duty Large Lathe 24in. & over swing |
1977 |
American |
2516-27 x 216 |
Fair |
sold |
Photo /
More Info. |
40" x 18ft: American manual lathe # 2516-27 x 216
center distance: 216" or 18ft
swing over bed: 40" ,over cross slide: 30"
chuck: 6 jaw 24" dia
12" steady rest
2.5" spindle bore
voltage: 575/3
CATALOGUE STD. SPECIFICATIONS:Hole Thru Spindle
2.5"Swing Over Bed Ways, Rated 40"Swing Over
Bed
Ways,30"Swing Over Cross-Slide
Distance Between Centers 216";Cross-Feed Travel
6"; Tailstock, Spindle Diameter 5"ailstock,
Spindle Travel 12";Tailstock, Spindle Taper #5
MT;(27) Spindle Speeds, Range 12 to 800 RPM(66)
Carriage Longitudinal Feeds .0025 to .1506
IPR(66) Thread Changes, Range 1 to 60 TPI Motor
Horsepower 40 |
|
Ad # 15929 | Heavy Duty Large Lathe 24in. & over swing |
1974 |
leblond |
7H |
Fair |
sold |
Photo /
More Info. |
36 x 72": leblond H7 manual lathe,raised headstock type
swing 36" over bed ways,30" over cross slide
center distance: 72"
3" spindle bore
includes: 15" 3 jaw chuck,18" 4 jaw chuck
steady rest
servo shift
inch threading
travel dial on z bed
|
|
Ad # 10269 | Heavy Duty Large Lathe 24in. & over swing |
|
Sculfurt |
34 x 216 |
Fair |
Sold |
Photo /
More Info. |
34in swing x 18ft centers: 34" swing over bed, 24" over cross slide
216" centers
4 jaw- 32" chuck
4" spindle bore
5MT in tailstock
std. 4way tool post
2 steady rests
coolant
lead screw needs re-installed-minor work--use vari-speed drive system
spindle:800rpm max30 HP
|
|
Ad # 4320 | Heavy Duty Large Lathe 24in. & over swing |
1993 |
Clausing Metosa |
C32120 |
Fair |
SOLD |
Photo /
More Info. |
32 x 120 Clausing Metosa Gap Bed Lathe: Swing in Gap: 41 1/2"
Width of Gap 15 1/2"
(15) Spindle Speeds: 11-1000 RPM
Spindle Bore: 4"
Inch, Metric,Modular,& Diametral Threading
Equipped With:
4 Jaw Chuck
Steady Rest
Follow Rest
Tool Post
Rapid Traverse
Coolant |
|
Ad # 14612 | Heavy Duty Large Lathe 24in. & over swing |
|
Best & miles |
50" x 90" |
Fair |
sold |
Photo /
More Info. |
50"swing x 90" centers: Best & Miles manual lathe
capacity: 50" swing over ways
center distance: 90"
20" steady rest
tailstock
20HP
220/3
note: has not been used in years but ran
when
last used... |
|
Ad # 4792 | Heavy Duty Large Lathe 24in. & over swing |
50? |
American |
24" |
Fair |
Sold |
Photo /
More Info. |
Heavy duty 36" swing x 72" centers lathe: 36" swing over ways, 16" over crosslide
72" center dist.
24" 4-jaw chuck
steady rest
11-450 RPM
taper attachment
20HP
Inch threading
|
|
Ad # 10248 | Heavy Duty Large Lathe 24in. & over swing |
1975 |
EX-CELL-O |
XD630N |
Good |
Sold |
Photo /
More Info. |
28 swing x 252"bed -metric machine: 28 swing over bed, 16" swing over cross slide
252" bed length =21ft
metric dials-
12" 3 jaw chuck
3-1/4" spindle bore
no gap in bed
5MT tailstock
rapid traverse on carriage
coolant
no readout(DRO)-will be removed
4 way toolpost
|
|
Ad # 14249 | Heavy Duty Large Lathe 24in. & over swing |
1971 |
Mazak-Hercules Ajax |
24" |
Good |
sold |
Photo /
More Info. |
24" swing x 10ft between centers: Mazak-Hercules Ajax Manual Lathe
Model: Mazak 24
Capacity: 24" swing x 10ft.
between centers
Swing Over Cross Slide:14.46"
2" spindle bore
Electrical: 220 / 3 phase
Includes:
2 steady rests
tapper attachment
3 jaw chuck
recently refurbished, very
good working order |
|
Ad # 13366 | Heavy Duty Large Lathe 24in. & over swing |
|
Swift |
19/21 C |
Good |
sold |
Photo /
More Info. |
40" swing x 23ft centers: Swift Model 19/21 C-gap frame bed
4 - 230 RPM
40"swing x 23ft centers
32" swing over crosslide
4" Spindle Bore
inch threading only
4 Jaw 64" Chuck
20" Dia max Steady Rest |
|
Ad # 6695 | Heavy Duty Large Lathe 24in. & over swing |
1970 |
MONARCH |
2516X96 |
Good |
Sold |
Photo /
More Info. |
27” x 96”cc MONARCH Series 80 Dyna-Shift H Duty Engine Lathe, 2516X96: 27” x 96”cc MONARCH Series 80 Dyna-Shift Heavy Duty Engine Lathe, Model 251... |
|
Ad # 13367 | Heavy Duty Large Lathe 24in. & over swing |
2004? |
Poreba |
TRP 93 x 6M |
Good |
sold |
Photo /
More Info. |
36" x 236": Poreba Model TRP 93 x 6M
Voltage 220/440 wired 220
Swing 36.6"
Swing in Gap 45.2"
Swing Over Cross Slide 24.9"
Distance Between Centers 236"
Spindle Drive Motor 50 hp
Spindle speed (Mimimum) 7.1 rpm
Spindle speed (Maximum) 710 rpm
Spindle Bore 4" 1/8
Chuck Size 31" 4 Jaw
Chuck indexs at 5 Degree incraments
Threading Inch/Metric
Machine Weight 35000 lbs
Floor Space Requirements 68" X 334"
2 Steady Rests 16" Max
1 steady rest 24" Max |
|
Ad # 6517 | Heavy Duty Large Lathe 24in. & over swing |
|
LeBlond |
LeBlond Model 25" |
Good |
Sold |
Photo /
More Info. |
25" x 25' Heavy Duty LeBlond Engine Lathe: Swing: 25"
Distance Between Centers: 25' (maybe a little more?)
Spindle Bore; 3"
Spindle Speeds: 5.5 rpm tp 625 rpm in 3 ranges
Inch Threading
18" 3-Jaw Chuck
Tailstock
4 Steady Rests - different sizes |
|
Ad # 9415 | Heavy Duty Large Lathe 24in. & over swing |
|
TOS |
SN71C |
Good |
sold |
Photo /
More Info. |
28"/40" x 157": Hole thru spindle 2.8"
Swing over bed ways, rated 27"
Swing over bed ways, actual 28"
Swing thru gap 40"
Swing over cross-slide 16.5"
Distance between centers 157"
Gap length 11.8"
Tailstock, spindle travel 9.4"
Tailstock, spindle taper #5 MT
(16) Spindle speeds, range 10-1000 rpm
Carriage longitudinal feeds 001-.251 ipr
Cross-Slide cross feeds 009-.125 ipr
Acu-Rite Digital Readouts
Removable Gap-Type Bed
12" 3-Jaw Chuck w/Jaws
Hardened & Ground Bed Ways
Inch-Metric Threading
(2) Steady Rests
Power Rapid Traverse
|
|
Ad # 14819 | Heavy Duty Large Lathe 24in. & over swing |
unknown |
Lodge & Shipley |
24" |
Good |
sold |
Photo /
More Info. |
24" x 16': Lodge & Shipley 24" manual lathe
Swing over bed: 27 1/2"
Swing over cross slide: 19"
Hole through Spindle: 2 1/2"
center distance :16ft
Morse Taper: No. 6
Number of spindle speeds: 12
Number of thread and feed changes: 65
Lead Screw Dia: 2 3/8"
HP: 15-20-25
1200 RPM
|
|
Ad # 9134 | Heavy Duty Large Lathe 24in. & over swing |
1997 |
Longem |
LG26120C |
Good |
Sold |
Photo /
More Info. |
26 x 120 W/ 36 inch gap: 26 inch swing x 120 centers
36 inch gap bed
4-1/8" spindle bore
face plate
QC toolpost
travel dial
12" 3 jaw chuck
16" 4 jaw chuck-scroll & 20" 4 jaw independent
2-steady rests & follower rest
rapid traverse on carriage |
|
Ad # 12728 | Heavy Duty Large Lathe 24in. & over swing |
1988 |
Nardini |
IN25200T |
Good |
sold |
Photo /
More Info. |
25" swing over ways x 200"centers: 1988 Nardini IN 25200T lathe
25" swing over bed, 20" over cross slide
center dist: 200" =16'6"
gap bed
18" 4 jaw chuck
Note: 18" 3 jaw chuck-not included
taper attach
5" follow rest x 2
8" steady rest
inch / metric threading
Newall 2 axis DRO
4 way std toolpost w/ no holders
4-3/4" spindle bore
16-1250 RPM
20 HP
rapid traverse
ways look very good
manuals
some spare parts
good machine runs well ...good tolerances |
|
Ad # 12930 | Heavy Duty Large Lathe 24in. & over swing |
|
LeBlond Regal Sliding Gap |
|
Good |
sold |
Photo /
More Info. |
25"swing x 9ft: LeBlond Regal Sliding Gap Bed 25" - 50" x 9' 8.5" - 15' 5"
S# 5H434, 25" Swing, 50" Swing in gap, Sliding Gap Bed, 9' 8.5" Bed length, 15' 5" Open, 12 Spindle speeds from 18 to 720 rpm, 48 Threading ranges from 2 to 112, 2 1/8" Thru hole, 12" 3 Jaw Cushman chuck, 30" Face plate, 2 axis Anilam Wizard Lathe Series DRO, Taper attachment, Quick change tool post, Hydraulic Hydra-Trace compound, 2 Roller bearing steady rest - 12.5" thru hole & 7.25" thru hole, 10hp 230/460v 3ph 60cyc, Cleaned & painted
|
|
Ad # 7202 | Heavy Duty Large Lathe 24in. & over swing |
1942 |
AXELSON |
24 H.D. |
Good |
Sold |
Photo /
More Info. |
28" x 120"cc AXELSON Heavy Duty Engine Lathe, Model 24 H.D.: 28" x 120"cc AXELSON Heavy Duty Engine Lathe, Model 24 H.D.
Max. swing over bedways: 28 3/4"
Max. swing over cross slide: 18 3/4"
Bed width: 26"
Hole through spindle: 2 5/16"
Spindle nose: 11" D-1
Travel of cross slide: 16 3/4"
Tailstock spindle diameter: 41/2"
Size of centers: No.5 M.T.
24 spindle speeds 6 to 555 RPM
81 feeds .004 to .300 IPR
Thread range: 1 to 30 T.P.I
EQUIPPED WITH:
Swivel compound
Camlock spindle nose
4-jaw chuck
14 3/4" Dia. capcity 3-point roller steady rest
Plain follow rest
Micrometer carriage stop
(2) Boring holders w/(1) boring bar
Pan bed with coolant tank ( less pump)
Work light
20 H.P. 3/60/220 Volt Motor |
|
Ad # 16001 | Heavy Duty Large Lathe 24in. & over swing |
1996 |
Poreba |
TRP93/3M |
Good |
sold |
Photo /
More Info. |
36" x 118" Poreba Heavy Duty Engine Lathe: Swing over Bedways: 36"
Swing over Cross Slides: 25"
Swing over (Removable) Gap: 45"
DBC: 118"
Hardened Ways
No taper attachment
Have gap for bed not shown
Wired 220/3
Inch/Metric Threading
Spindle Speeds: 7.1 - 710 rpm
Spindle Bore" 3-5/8"
Spindle Power: 35 hp 220/440 volts
Also Includes: electrics
4-Way Tool Post
3-Jaw Chuck: 19" diam.
4-Jaw Chuck: 31" diam.
(2) 16" Capacity Roller Type Steady Rests
|
|
Ad # 5818 | Heavy Duty Large Lathe 24in. & over swing |
|
NOBLE & LUND |
106in x 27ft Lathe |
Good |
SOLD |
Photo /
More Info. |
106" X 27' NOBLE & LUND HEAVY DUTY ENGINE LATHE: SWING OVER BED: 106"
SWING OVER CROSS SLIDE: 90"
DISTANCE BETWEEN CENTERS: 27'
SPINDLE SPEEDS: .72 TO 42.5 RPM
SLIDING FEEDS: .0037 TO .1666 IPR
SURFACING FEEDS: 1/2 OF SLIDING FEEDS
WIDTH OF 4-WAY BED: 88"
MOTOR & CONTROLS: AC
EQUIPPED WITH:
96" 4-JAW CHUCK
CLAMP TYPE TOOL POST
(1) CARRIAGE WITH 4-WAY RAPID TRAVERSE
(1) 3-POINT STEADY REST (24" OPENING)
(1) 4-POINT STEADY REST (24" OPENING)
WINDOW TYPE HEADSTOCK
THIS MACHINE HAS NO LEADSCREW OR THREADING CAPABILITY. |
|
Ad # 15600 | Heavy Duty Large Lathe 24in. & over swing |
199? |
Longem |
LG26120C |
Good |
sold |
Photo /
More Info. |
26" swing x 120" centers: Longem 26 x 120" manual gap bed lathe #LG26120
swing over bed 26",over crosslide:15.5"
D1-8 camlock spindle
inch/metric threading
10 hp main motor
center dist:120"
spindlle bore:4-1/8"
taper attachment
steady rest: up to 12" max
spindle rpm:13-1600rpm:24speeds
swing in gap:34"
chucks: 3 jaw 16" dia,4 jaw 20" dia
note:no tooling nor tool post not included,rapid traverse on bed needs new engage switch |
|
Ad # 11910 | Heavy Duty Large Lathe 24in. & over swing |
1977 |
Ponar-Wroclaw |
Tur-63 |
Good |
sold |
Photo /
More Info. |
24 swing x 72" centers: 1977 Ponar-Wroclaw Tur-63 Lathe
24" swing over bed, 14" over cross slide
18-1800 Rev/min
taper attachment
3" spindle bore
12" 3 jaw chuck
16" 4 jaw chuck
face plate
steady rest 12" & 6" |
|
Ad # 13421 | Heavy Duty Large Lathe 24in. & over swing |
1979 |
Tos |
SUS 63 |
Good |
sold |
Photo /
More Info. |
25" x 320": TOS Engine Lathe
Model: SUS 63 | Age: 1979 | Ref #:
20629
Specifications:
Maximum Swing Over Bedways 25"
Maximum Swing Over Cross Slide 15.3"
Distance Between Centers 320"
Spindle Hole Diameter 3.2"
Spindle Speeds: (22) 9-1120 RPM
Spindle Nose (Camlock) D1-11
Cross Slide Traverse 16.5"
Tool Rest Traverse 8"
Dimensions of 4-Way Tool Post 8.5" x 8.5"
Number Positions 4-Way TP Adjustable 24
Tailstock Quill Diameter 5.1"
Tailstock Quill Travel 13"
Tailstock Taper #6 MT
Tailsock Max Thrust Force 7,720 lbs
Maximum Work Piece Capacity 13,300 lbs
Longitudinal Feeds: .0022-.0591 IPR
Threads, Inch .125-56 TPI
Threads, Metric .5-112 MM
Threads, Whitworth .25-56 TPI
Threads, Module .25-56
Threads, DP .5-112
Threads, CP .0015-3.5
Bed Width 23"
Bed Height 32"
Machine Dimensions (L x W x H) 400" x 69" x
55"
Machine Weight 20,500 lbs
EQUIPPED WITH:
20" 4-Jaw Chuck
4-Way Tool Post with 24 Adjustable
Positions
Inch/Metric/Whitworth/Module/DP & CP
Threading
Hardened & Ground Ways
(1) 15" Capacity Steady Rest
Follow Rest
Leadscrew & Feed Shaft Support
Coolant System
Full Length Chip Pan
30 HP Spindle Drive Motor 220/380/440/3/60
Also Available at Additonal Cost:
(2) 26" 4-Jaw Chucks (#20644 & #20645)
(1) Adjustable Tool Post Milling Attachment
(#20640)
(1) Fixed Tool Post Mill Attachment
(#20641)
Excellent Condition!
|
|
Ad # 16084 | Heavy Duty Large Lathe 24in. & over swing |
1959 |
axelson |
3020 |
Good |
sold |
Photo /
More Info. |
35 x 12 ft bc: 1959 model Axelson 35.5" swing x 15' bed length
overall
between centers 12ft thru spindle hole 9-
1/4""
4 jaw chucks
480/3 volt
air over hydraulic clutch
Bought 1980 paid $58,000.00
We had ways scrapped in 1998, rebuilt taper
attachment
1959 Model
Axelson with 9" spindle double 4 jaw chucks,
air over hydraulic clutch, I should have 2
steady rests (1 large 1 small)If I can find
them.??
I bought Axelson in 1980,in 1997 I had the
taper
attachment ground & ways scraped.
I sent this machine to Gates Machine Tool
Repair in Manvel Tx. and paid $10,000.00 to
have it repaired & sent this lathe up here.
It's been sitting here since reworked |
|
Ad # 13654 | Heavy Duty Large Lathe 24in. & over swing |
1945 |
Monarch |
36 NN |
Good |
sold |
Photo /
More Info. |
53"swing x 84" centers: Monarch 36 NN
Year: 1945
Voltage: 220 3Phase
RPM 6 - 303
threading:inch only
53" Swing x 84" between centers
44" over crosslide
4 Jaw Chuck 40"
Face Plate: 48"
Tail Stock 4 Jaw 19 1/2" live center chuck
Fabricated Steady Rest
includes some tooling-holders
Box w/tool holders |
|
Ad # 13615 | Heavy Duty Large Lathe 24in. & over swing |
|
Nebel Lathe |
Gap Bed |
Good |
sold |
Photo /
More Info. |
52" x 72"centers: Nebel Sliding gap Lathe
52" Swing in Gap 48" Between the Sliding gap
30" Over crosslide 72" between centers Gap Closed
44" Face Plate with VTL Jaws
Moorse Taper Number 6 on Tail Stock
Tamper attachment
3" 1/8" Spindle Bore
5-230 RPM |
|
Ad # 10716 | Heavy Duty Large Lathe 24in. & over swing |
|
Putnam |
LH-3-8170 |
Good |
Sold |
Photo /
More Info. |
46" swing over bed,34" over cross slide x 6ft centers: 46" swing over bed ways, 34" over cross slide
spindle speeds: 3.84-192 RPM (18) speed
4 way std. toolpost
taper attachment
36" 4 jaw chuck
6 ft between centers
5MT tailstock
17" steady rest
2" spindle bore
25HP |
|
Ad # 11384 | Heavy Duty Large Lathe 24in. & over swing |
|
Greaves Klusman |
|
Good |
sold |
Photo /
More Info. |
40" x 100" : 40" Swing Over Bed
100" Center Distance
32 inch 4 Jaw chuck
2" Spindle Hole
28-200 RPM? |
|
Ad # 8803 | Heavy Duty Large Lathe 24in. & over swing |
|
Granor |
24 x 132 |
Good |
SOLD |
Photo /
More Info. |
24 x 11 ft: 24" swing over ways , 16" over cross slide
large gap in bed swings 42" x 12" wide
20" 4 jaw chuck
taper attachment
steady rest
3-1/2" spindle bore
9-450 RPm
|
|
Ad # 12234 | Heavy Duty Large Lathe 24in. & over swing |
|
American |
24 |
Good |
sold |
Photo /
More Info. |
24" swing x 17ft: American 24"
24" swing x 17 ftcenters
11-450 RPM
16" x over cross slide
2" 1/4 Spindle Bore
Power Rapid traverse on carriage
21" 4 Jaw Chuck
Steady Rest
Voltage 440/ 3 Phase |
|
Ad # 12314 | Heavy Duty Large Lathe 24in. & over swing |
|
American Pacemaker |
20 x 96 |
Good |
sold |
Photo /
More Info. |
24" x 96" : American Pacemaker
24" x 96"
18-1200 RPM
Steady Rest 10"
Voltage 220
20 Hp
2" 1/8 Spindle Bore
3 Jaw 18" chuck
15" Swing Over the Crosslide
Taper Attachment |
|
Ad # 11376 | Heavy Duty Large Lathe 24in. & over swing |
1940s |
American tool Works |
24" |
Good |
sold |
Photo /
More Info. |
24" x 50" : American Tool Works 24" Heavy duty Lathe
24" x 50"
18" 4 Jaw Chuck
Swing
27" 1/2" Over bed
17" over Carriage
Range of threads per inch 1/2 to 28
15 - 280 RPM
Taper Attachment
Spindle Hole Diameter 2 1/8
Centers Morse Tape No.5
Steady rest capacity 9"
220/3phase
|
|
Ad # 9812 | Heavy Duty Large Lathe 24in. & over swing |
1960's |
Cincinnati |
Hydrashift |
Good |
sold |
Photo /
More Info. |
26 x 96: tailstock,
15"-3jaw, steady rest,
inch threading,
2-5/16 hole thru spindle |
|
Ad # 15508 | Heavy Duty Large Lathe 24in. & over swing |
1942 |
Niles Tool Works |
A 12-3 |
Good |
sold |
Photo /
More Info. |
56" swing over bed x 276" between centers: Niles Tool Works Engine Lathe
Capacity: 54" Swing x 276" between centers
Specifications:
Swing Over Bed: 54"
swing over cross slide:44"
Distance Between Centers:276"
Spindle Speeds: (12) 3.94
- 232 RPM
Motor (Est.):50 HP
Equipped With:
36" 4-Jaw Chuck
(3) Steady Rests
Tool Post
10" Riser Block
Pendant Control
Can be seen under power. |
|
Ad # 14320 | Heavy Duty Large Lathe 24in. & over swing |
1979 |
Technoimplex |
Ms2 |
Good |
sold |
Photo /
More Info. |
32 x 114: 31" 4 jaw
22" 3 jaw
114" center
32" swing
Steady rest
Tool post
Taper attachment
3" thru hole
Tail stock
25 hp
|
|
Ad # 13202 | Heavy Duty Large Lathe 24in. & over swing |
1981 |
Hitachi |
4ne 2-600 |
Good |
sold |
No Photo /
More Info. |
: Great Machine no use for it need to sell it. |
|
Ad # 12927 | Heavy Duty Large Lathe 24in. & over swing |
1944 |
Hendey |
24 x 72 80 centers |
Good |
sold |
Photo /
More Info. |
: |
|
Ad # 11909 | Heavy Duty Large Lathe 24in. & over swing |
1987 |
Tos |
SN63C |
Good |
sold |
Photo /
More Info. |
25 swing x 157": 1987 Tos SN63C Lathe
25" swing over gap bed, 13" swing over cross slide
inch/metric threads
steady rest
followo rest
12" 3 jaw chuck
coolant
rapid traverse-needs motor voltage changed to 220/3 to run
3.5" spindle bore
10-100 rem/ min spindle speed
manuals |
|
Ad # 6694 | Heavy Duty Large Lathe 24in. & over swing |
1960 |
MONARCH |
2516X72 |
Good |
Sold |
Photo /
More Info. |
27”x72”cc MONARCH Series 80 Dyna-Shift H Duty Engine Lathe, 2516X72 : 27”x72”cc MONARCH Series 80 Dyna-Shift Heavy Duty Engine Lathe, Model 2516X... |
|
Ad # 4036 | Heavy Duty Large Lathe 24in. & over swing |
1965 |
LEBLOND |
2516-20 |
Good |
sold |
Photo /
More Info. |
23" x 54" LEBLOND H.D HEAVY DUTY ENGINE LATHE : MAXIMUM SWING OVER BED WAYS: 29"
DISTANCE BETWEEN CENTERS: 54"
SPINDLE BORE: 2 1/16"
SPINDLE NOSE: L-2 TAPERED KEYCROSS SLIDE TRAVEL: 14 1/2"
TAIL STOCK SPINDLE DIAMETER: 4 1/2"
TAIL STOCK SPINDLE TAPER: #5 M.T.
27 SPINDLE SPEEDS: 12 TO 1500 RPM
109 FEEDS: .001-.205 IPR
THREAD RANGE: 2 TO 360 T.P.I.
|
|
Ad # 11586 | Heavy Duty Large Lathe 24in. & over swing |
1964 |
VDF |
V1250 |
Good |
sold |
Photo /
More Info. |
50"swing x 20ft centers: 1964 VDF V1250
50"swing x 20 ft centers
40" over the cross slide
spindle bore:4-1/2" first 11" length stepped down to
3-1/4" chuck has 4.5" bore
4 Jaw Chuck 48"
Steady Rest 24" max opening
inch/metric threads
50 HP
Tail Stock
Rapid Travel
RPM Range:300 max
rigger fee to load: approx: $2000.00 |
|
Ad # 8910 | Heavy Duty Large Lathe 24in. & over swing |
|
Summit |
42 x 20ft |
Good |
SOLD |
Photo /
More Info. |
42in x 20ft: SUMMIT ENGINE LATHE
Description
42 " x 20ft
1 used - Summit Engine Lathe Serial # 10068
#6 Morris taper in tail stock
40" wide Hardened and Ground bedway
Coolant and trays
Follow rest
220/440 3 phase
5 to 800 RPM
39" 4-Jaw Chuck
2' Gap
42" swing over ways
56" swing thru gap
6 1/4" spindle hole
20' Centers
Rapid travels
Taper
4 way tool post
27" Steady rest
Cuts in: Whitworth, Metric, Modulus, Diametric |
|
Ad # 14628 | Heavy Duty Large Lathe 24in. & over swing |
? |
Niles |
52" x 12' |
Good |
sold |
Photo /
More Info. |
52" swing x 12' centers: Niles Engine Lathe
capacity:52" swing over bed ways ,42" over cross
slide x 12ft center distance
48" 3 jaw chuck
30HP main motor
steadyrest |
|
Ad # 14144 | Heavy Duty Large Lathe 24in. & over swing |
|
Axelson |
38" |
Good |
sold |
Photo /
More Info. |
38": Axelson 38" Lathe |
|
Ad # 9335 | Heavy Duty Large Lathe 24in. & over swing |
1961 |
Kramatorsk |
1660 |
Good |
sold |
Photo /
More Info. |
30 tons: max dia of workpiece 1250 mm.
weight of workpiece 30 tons.
distantion between centers 6300 mm.
weight of machine 47 tons. |
|
Ad # 12698 | Heavy Duty Large Lathe 24in. & over swing |
1946 |
American |
27" |
Good |
sold |
Photo /
More Info. |
28" x 20 Ft: American Lathe
Model 27"
28" swing x 20 Ft centers
RPM 11 - 450
4 Jaw 28" Chuck
2 Steady rests 8" and 12"
20" swing over cross slide
includes a toolpost grinder |
|
Ad # 11954 | Heavy Duty Large Lathe 24in. & over swing |
1942 |
Monarch |
|
Good |
sold |
Photo /
More Info. |
24.5" swing x 48" between centers: Monarch Engine Lathe, serial #15309
24.5" swing x 48" between centers
Speeds, 10- 450
Inch threading
26" faceplate
220/480 Volt, 3 Phase |
|
Ad # 7913 | Heavy Duty Large Lathe 24in. & over swing |
50's |
AMERICAN |
42in Raised |
Good |
Sold |
Photo /
More Info. |
50" x 120" Raised (11") American Heavy Duty Lathe: Swing Over Bed: 50", swing over cross slide: 36"
Distance Across Ways: 32"
Distance Between Centers: 120"
Center Raised By 11"
48" Diam. 4-Jaw Chuck without jaws but spacing is 6 inch between vertical parallel slots.
Spindle Speed Ranges:1- 157 rpm in 18 Stages
Inch Threading
Powered compound & cross feed
Heavy Duty Steadyrest
Headstock & tailstock raised to match up
HP-40
|
|
Ad # 8805 | Heavy Duty Large Lathe 24in. & over swing |
|
Reed & Prentice |
24 x 84" |
Good |
SOLD |
Photo /
More Info. |
24 x 7 ft: 24" swing over ways, 14 over cross slide
7ft between centers approx
18" 4 jaw chuck
2-1/2" spindle bore
12-530 rpm
|
|
Ad # 7500 | Heavy Duty Large Lathe 24in. & over swing |
1942 |
Monarch |
27N |
Good |
SOLD |
Photo /
More Info. |
1942 MONARCH 27N 30.5" x 108"cc Lathe: 108" Betw Centrs
30.5" Swing
30 HP
6-303 RPM
Tailstock
Coolant System
Chip Guard
Fresh Paint
* All machinery specifications must be independently verified by buyer. All machinery sales are subject to prior sale. Any agreement to purchase or sell machinery must be in writing.
Full Machine Specifications
Distance Between Centers 108"
Swing 30.5"
Weight 18000 LBS
HP 30
RPM 6-303
Equipped With
Tailstock
3 Steady Rests 12",14",18"
Bull nose Live Centers 4", 6", 7",12"
4 jaw Chuck 21"
3 Jaw chuck 18"
Coolant System
Chip Guard
Fresh Paint |
|
Ad # 1721 | Heavy Duty Large Lathe 24in. & over swing |
1965 ? |
LeBlond |
Regal |
Good |
Sold |
Photo /
More Info. |
LeBlond Regal 26" x 120" Engine Lathe: Swing: 26" over bed, swing over cross slide-19"
DCB: 120"centers
3" spindle bore ?
Steady Rest
Quick Change Tool Post
Gear Driven Spindle
Inch Threading
Coolant System
4-Jaw Chuck |
|
Ad # 7912 | Heavy Duty Large Lathe 24in. & over swing |
|
Bridgeford |
32 x 196 |
Good |
Sold |
Photo /
More Info. |
32" x 196" Heavy Duty American Lathe: Swing Over Gap: 32"
Swing Over Bed: 34"
Bed Width: 21"
Chuck: 23" diam., 4-Jaw
Hand Cranked Tailstock
Steady Rest
Spindle Speeds: 6.5 - 166 rpm in 9 stages
Inch Threading (Left hand and Right hand)
|
|
Ad # 5597 | Heavy Duty Large Lathe 24in. & over swing |
|
LeBLOND |
45 x 80 HD Lathe |
Good |
SOLD |
Photo /
More Info. |
45" X 180" LEBLOND HEAVY DUTY ENGINE LATHE: MAXIMUM SWING OVER BED: 45"
MAXIMUM SWING OVER CROSS SLIDE: 28-1/2"
DISTANCE BETWEEN CENTERS: 180"
SPINDLE SPEEDS: (27) 1.5 TO 165 RPM
SPINDLE HOLE: 3-1/4"
FEEDS: (54) .005" TO .308"
THREADS: (54) 1/2 TO 30 TPI
CROSS SLIDE TRAVEL: 27-1/2"
COMPOUND REST TRAVEL: 15"
TAILSTOCK SPINDLE TRAVEL: 20"
TAILSTOCK SPINDLE TAPER: NO. 6 MT
WIDTH OF BED: 42"
MOTOR: 40 HP
EQUIPPED WITH:
44" FACEPLATE W/4 BORING MILL JAWS
TAPER ATTACHMENT
HARDWAYS
(2) STEADY REST
TAILSTOCK
THREAD DIAL |
|
Ad # 5178 | Heavy Duty Large Lathe 24in. & over swing |
|
Oelikon |
DMI |
Good |
sold |
Photo /
More Info. |
Swiss Built 24" x 108" Gap Bed Lathe: Oelikon Swiss Built
24" x 108" Gap Bed Lathe
Swing: 24"
centers 108"
Swing Over Cross Slides: 18"
Inch + Metric Threading
Spindle Bore: 1-1/2"
Spindle Speeds: 40 - 1,000 rpm
Coolant
note: no tailstock |
|
Ad # 10270 | Heavy Duty Large Lathe 24in. & over swing |
|
Niles |
30 x 264 |
Good |
Sold |
Photo /
More Info. |
30" swing x 264 " bed: 30" swing ober bed ways, 28" swing over crosslide
bed 22ft length centers 264"
4 jaw -36" chuck
2 steady rests
30 HP
37-394 rpm
QC toolpost
|
|
Ad # 16158 | Heavy Duty Large Lathe 24in. & over swing |
90s ? |
Poreba |
TPK 90A1/3M |
Good |
sold |
Photo /
More Info. |
36"swing x 120"centers: Poreba # TPK 90A1/3M Lathe:
Std. Mfg specs below-please verify actual
machines..
36"swing x 120"centers
24" Dia 6 jaw chuck shown and few other
Acc.not shown in pix..steady rest,chuck?
DRO-2 axis included
Std. Mfg specs below
SPECIFICATIONS:
SWING OVER BED: 36 1/2" (927 mm)
SWING OVER CROSS SLIDE: 25"
SWING IN GAP: 49"
LENGTH OF GAP: 17"
DISTANCE BETWEEN CENTER: 120" (3048 mm)
SPINDLE BORE: 3 3/4"
SPINDLE NOSE: A1-11
SPINDLE MOTOR: 20/30 HP
SPINDLE SPEEDS (2 RANGES): 7.1-710 RPM
FEEDS - LONG. (122): .0043-.5 IPM
- CROSS (122): .0021-.25 IPM
- TOP SLIDE: .001-.125 IPM
THREADING - INCH 1/4-30 TPI
- METRIC: 1-120 MM/REV
CROSS SLIDE TRAVEL: 18 1/2"
TOP SLIDE TRAVEL: 11 3/4"
RAPID TRAVERSE - LONG./CROSS: 260/130 IPM
- TOP SLIDE: 65 IPM
TAILSTOCK - DRILLING, DIAMETER: 5 1/8"
- DRILLING LENGTH: 40"
- TAPER: #6 MT
- TRAVEL: 11 3/4"
ELECTRICS: 440V/3Ph/60hZ
|
|
Ad # 5817 | Heavy Duty Large Lathe 24in. & over swing |
1960 |
DORTMUND |
22ft SWING x 60ft LONG |
Good |
SOLD |
Photo /
More Info. |
22' X 60' MFD DORTMUND HEAVY DUTY LATHE: MAXIMUM SWING: 22'4"
MAXIMUM CENTER DISTANCE: 60'
MAXIMUM WORKPIECE WEIGHT CAPACITY: 88 TONS
SPINDLE SPEEDS: (20) 0.3 TO 24 RPM
FEED RANGE: (20) .0053" TO 0.424"
MOTOR: 55 KW
HORIZONTAL DRILLING ATTACHMENT
16'4" FACEPLATE
TAILSTOCK
OPERATOR CONTROL PLATFORM
NOTE - MODULAR TYPE LATHE WITH 60' OF T-SLOTTED
FLOORPLATE, 18' WIDE. |
|
Ad # 5950 | Heavy Duty Large Lathe 24in. & over swing |
1952 |
MONARCH |
N |
Good |
sold |
Photo /
More Info. |
25” x 72”cc MONARCH Model N Heavy Duty Engine Lathe: 25” x 72”cc MONARCH Model N Heavy Duty Engine Lathe
Max. swing over bed ways 27 ½”
Max. swing over compound rest 14”
Spindle bore 2 3/16”
Bed width 25”
Top slide travel 6”
Tailstock spindle diameter 4 7/8”
Tailstock spindle taper No.6 M.T.
Tailstock spindle travel 8 ½”
16 Spindle speeds 8-405 RPM
48 feeds .0038-.240 IPR
Thread range 1 ½ - 92 T.P.I.
EQUIPPED WITH:
Flame hardened bed ways
Swivel compound
D1-8” Camlock spindle
24” Dia. 4-jaw chuck
16” Dia. back-plate
Chip pan
30 H.P. 3/60/480 Volt Motor
|
|
Ad # 7301 | Heavy Duty Large Lathe 24in. & over swing |
1968 |
Martin |
DS-99 |
Good |
sold |
Photo /
More Info. |
40" x 176" Engine Lathe: Swing over Ways: 40" (approx)
Distance Between Centers: 178" (from spindle nose to END of Bed)
Spindle Through Bore: 3-1/2" |
|
Ad # 10273 | Heavy Duty Large Lathe 24in. & over swing |
|
Leblond |
Regal 24 |
Good |
Sold |
Photo /
More Info. |
26" swing x 13ft centers-2 available: 26" swing over bed, 20" over cross slide
16" 4 jaw chuck
Spindle bore: 2"
inch threads
taper attachment
13 ft centers=156"
toolpost
coolant
rpm: 27-1080
20 HP
2 machines alike available |
|
Ad # 6480 | Heavy Duty Large Lathe 24in. & over swing |
|
TOS |
55B-71B |
Good |
sold |
Photo /
More Info. |
26´´ X 86´´ TOS GAP BED ENGINE LATHE: 26´´ X 86´´ TOS GAP BED ENGINE LATHE:
SWING OVER WAYS ..................... 26´´
SWING OVER CROSS SLIDE .............. 14´´
DISTANCE BETWEEN CENTERS ............ 86´´
SWING IN GAP ........................ 36´´
LENGHT OF GAP ....................... 16-1/2´´
SPINDLE SPEEDS ...................... (16) 10 TO 1000 RPM
LONGITUDINAL FEEDS .................. (38) 0.002 TO 0.0311 IPR
CROSS FEEDS ......................... (38) .0005 TO 0.028 IPR
THREADS ............................. (38) 2 TO 72 TPI
METRIC THREADS ...................... (38) .2 TO 4 MM PITCH
DIAMETER OF SPINDLE HOLE ............ 3´´
THREAD DIAL ......................... YES
SPINDLE FORWARD AND REVERSE ......... YES
HARD WAYS ........................... YES
MOTOR ............................... 7.5 HORSEPOWER |
|
Ad # 11580 | Heavy Duty Large Lathe 24in. & over swing |
|
Lodge & Shiply |
32" |
Needs Work |
sold |
Photo /
More Info. |
32"swing x 48"bed: Lodge & Shipley 32"
32" x 48"
3 Jaw 32" chuck
2" 1/2 Spindle Bore
Crossfeed rate 0.200
Power tailstock
Rapid Advance |
|
Ad # 1544 | Heavy Duty Large Lathe 24in. & over swing |
NEW |
Lansing |
Lansing G 43" x 120" |
New |
SOLD |
Photo /
More Info. |
20 3/4" Bore LANSING ‘G’ Semi-Automatic Oil Country Lathe: Swing Over Bed: 43"
DBC: 120"
Swing In Gap 58”
Swing Over Cross Slide 33”
Length of Gap 20”
Width of Bed 29 ½”
Spindle Bore 20 ¾”
Spindle Nose A1-28
Number of Speed Steps 3
Range of Spindle Speeds 0 – 177rpm
Tool Retractor Slide Travel 1 ¼”
Compound Slide Travel 14 ½”
Cross Slide (width x travel) 13 ½” x 25”
STEADY REST 3 Roller Jaws – Capacity 5” – 23”
FEEDS
Number of Longitudinal & Cross Feeds 40
Range of Longitudinal Feeds .004” - .064”
Range of Cross & Compound Feeds .003” - .053”
Rapid – Longitudinal 60”/min.
Rapid – Cross Slide 30”/min.
Rapid – Compound Slide 30”/min.
THREADS
40 Metric Threads .5 – 7.5
160 Inch Threads (TPI) Standard 60-4 120 – 1
40 Module Threads .25 – 3.75
40 Diametral Threads 120 – 8
TAILSTOCK
Quill Diameter 6”
Morse Taper M.T. #6
Quill Travel 14”
TAPER ATTACHMENT
Length of Travel 25 ½”
Amount of Taper Offset ±3 ½” / Ft.
MOTORS
Spindle 60 HP / DC
|
|
Ad # 7302 | Heavy Duty Large Lathe 24in. & over swing |
1952 |
Monarch |
32 in, NN |
Very Good |
SOLD |
Photo /
More Info. |
40" x 180" Monarch Engine Lathe: Swing: Approx 40.5"
Distance Between Centers: 180"
Spindle Through Bore: 2-1/2"
Spindle Speed Range: 8 - 405 rpm (via gears)
28" Independant 4-Jaw Chuck with manual Face Plate
Tailstock
Taper Attachment
Steady Rest
Distance Between Ways: 24"
Inch Threading |
|
Ad # 5633 | Heavy Duty Large Lathe 24in. & over swing |
50's |
LeBlond |
25 x 72 |
Very Good |
Sold |
Photo /
More Info. |
25" x 72" Leblond Heavy Duty Engine Lathe: 2 1/4 spindle bore
25" x 72" capacity
Manual, no gap
32" Max swing over bed - 20" over cross slide
72" centers
Rapid traverse
16" 3 jaw chuck
face pictures
4 way toolpost
no gap in bed..
tapper attachment
5-600RPM
english threads only
30 HP |
|