|
Ad Number: 15744
|
|
Year: | Make: Pandjiris | Model: 1200 manipulater
|
| Machine Type: | Condition: Good | Price: 67995.00
|
Description:
Panjiris # 1200
manipulater seam tank
welder w/ Lincoln BA-
5 rotating welding
head
note: these are
std mfg specs -please
verify actual
machines below..
The Series “1200″
Manipulator, was
original a Series
1100 before being
customized by
Pandjiris
Its basic size of
12′ x 12′, is mounted
on a bolt-down base
and has an 12′
nominal arc height
along with a 12′
horizontal boom
stroke at a variable
speed of 3″ to 116″
per minute. This is
electronically
controlled with
dynamic braking
beginning 19-1/4″
from the centerline
of the column and 360
degree manual column
rotation. The
standard electricals
are 460 volts, 3
phase, 60 cycle with
115 control. Wired to
conform to National
Electrical Code
Standards.
The manipulator
boom is complemented
by a Lincoln NA-5 Sub
Arc welder and Air
Powered Flux Recovery
System to deposit
more weld metal at
fast travel speeds.
This welder easily
adapts to a wide
range of wire feed
speeds and sizes.
11 ft boom stroke
vert boom
travel:16-7/8"-11'-9-
7/8"
wt
capacity:1200lbs
height 15'1"
mighty mac -flux
recovery unit # SR5-
3000
Idealarc DC600
welding unit
The Series
"1100" Manipulator,
size 11 x 11, is
mounted on a bolt-
down base. It has an
11' nominal
arc height and a
11' horizontal boom
stroke at a variable
speed of 3" to 116"
per minute. This is
electronically
controlled with
dynamic braking
beginning 19-1/4"
from the centerline
of the column and 360
degree manual
column rotation.
The standard
electricals are
230/460 volts, 3
phase, 60 cycle with
115 control. Wired to
conform to
National Electrical
Code Standards.
Vertical Boom
Travel . . . . . . .
. . . 16-7/8"
Minimum, 11' 9-7/8"
Maximum, Floor to
Bottom of Boom.
Hoist Speed . . .
. . . . . . . . . . .
. . 48 IPM Constant
Speed
Hoist Motor . . .
. . . . . . . . . . .
. . 1/2 H.P. AC
Brakemotor
Horizontal Boom
Stroke . . . . . . .
11' Stroke beginning
19-1/4" From Center
of Column
Horizontal Boom
Speed . . . . . . . 3
to 116 IPM Variable
Speed
Horizontal Boom
Motor . . . . . . .
1/2 H.P. DC Motor
Anti-Fall Device
. . . . . . . . . . .
. . . . . Spring
loaded, self
energizing pawl
mounted on the
crosshead and a
column mounted rack.
Column Rotation .
. . . . . . . . . . .
. . . . Manual 360
degree rotation with
a manually operated
screw friction lock.
Bolt Down Base .
. . . . . . . . . . .
. . . . Size 24" x
24", with (8) 11/16"
Drilled holes on 22-
1/4" bolt center.
Control . . . . .
. . . . . . . . . . .
. . . . . . . Pendant
control equipped with
joystick for Boom
"Up-Down-In-Out".
Boom Speed
Potentiometer and a
Weld-Rapid Selector
Switch. Pendant
Controls operate on
115
volts on 25' of
rubber covered cable.
Electrical . . .
. . . . . . . . . . .
. . . . . . . . . All
wiring is to National
Electrical Code
Standards. Draws 4
amps @ 460 VAC.
A Overall Height
15' 1-5/16"
B Boom Track
Blade 13-1/8"
C Min. Rear
Clearance 19-1/4"
D Boom Retract
19-1/4"
E Boom Stroke 11'
F C.G. Distance
18"
G Max. Load
End/Total 500/1000
H Max. Boom
Height 11' 9-7/8"
I Min. Boom
Height 16-7/8"
J Boom Centerline
Offset 11-1/8
For column or
boom
addition/deletion
For free standing
base
Preset digital
tachometer in
manipulator joystick
hand pendant, reads
in IPM or CmPM,
for boom
For variable
speed hoist, 2 to 46
IPM
For "Step-Over"
control, allows
indexing of boom
movement for overlay
operations etc
For flashing red
light at column top
and boom end
For special
voltages
Power rotation of
column for special
applications,
variable speed at
.004 to .12 RPM
For support
platform bolted to
column for welding
power source:
Standard 40x42
for single head
mounting
Oversized 44x60
for multiple head
mounting |
|
|
