| Year:
| 2007
|
| Make:
| Betenbender
|
| Model:
| 16-10
|
| Condition:
| Excellent
|
| Serial #:
| On Request
|
|
| Machine Status: | In Storage
|
| Shipping Info: | Requires rigger
|
| Weight: | 20000
|
| Dimension: L x W x H | 19ft x 8ft x 5ft |
Machine Location:
|
| City: |
On Request
|
| State: |
Pennsylvania
|
Country:
|
USA
|
Price:
|
$Sold USD
|
|
| General Description |
- ** MADE IN THE U.S.A. **
BETENBENDER HYDRAULIC SHEAR QUOTE
Model 16-125, 16' x 10ga.(mild steel)
SPECIFICATIONS:
Capacity - A-36 Mild Steel (80,000 lb. tensile) 10ga.
304 Stainless Steel(At Highest Rake) 10ga.Non Production
Main Motor (H.P.) ............................ 15
Nominal Cutting Length ........................ 196 inches
Number of Holddowns ........................... 28
Knives (Four(4) Cutting Edges) ................ 196"x1"x4"
Rake of Moving Blade (per foot) ............... 1/4
Back Gauge Range .............................. 36 inches
Strokes Per Minute ............................ 15
Oil Reservoir (Hydraulic Oil Included). . . . . . . 56 Gallons
Shipping Weight ............................... 20,000 lbs.
Machine Dimensions:
Overall Height ....... 61 inches
Overall Length .... 204 inches
Overall Width .. 76 inches(Including Backgauge)
Electrical Requirements ................. 230V-28amp/460V-14amp
Recommended Power Line .................. 230V-8ga/460v-12ga
BED - Steel one piece box section, stress relieved; welded to side frame insures positive alignment of bed and housings with beam supports that have removable wear tops which allow (1) convenient change to solid top and (2) plates with pin gauging.
RAM - Steel, stress relieved. Truss rod construction assures blade parallelism without consuming, short span adjustments.
POWER RAKE - allows change of blade rake angle for minimum camber & twist.
HYDRO-MECHANICAL HOLDDOWN - firmly grips material to prevent movement and
tipping. Optional urethane gripping pad protects soft and polished materials from marking.
ALLOY BRONZE GIBS - provides long service life and allow minimum running clearance for accurate control of blade clearance setting.
FOOTSWITCH CONTROL - is activated from a fully shrouded portable footswitch operating on 120 volts.
continued>>>
16' x 10ga. cont'd -2-
DRIVE - two hydraulic cylinders pushing or pulling directly on crosshead, no rotating pin action saving on wear.
HYDRAULIC VALVES - in manifold block for a minimum of fitting and piping; "C" frame motor for precision alignment of pump.
STANDARD EQUIPMENT
36" Power Backgauge With Hour Meter
L.E.D. Readout 48" Squaring Arm With Inlaid Scale
NEMA/Square D Electrics Light Beam/Shadow Line
All Hydraulic Fluid Included All Steel Construction
American Made Motor Disconnect Switch
Hydraulic Self-Compensating 1” x 4” Knives - (4) Cutting Edges
Holddown Bar Assembly Disconnect Switch
Power Adjust Variable Rake Manual Swing Up Backgauge
16ft cut length x 10Ga. capacity (1/8")
solid table top
one shot lube
361 run time(power on) hrs on machine, very low actual cut time!
Automec Fully programmable fron power back gage
5 preset programmable power 36 in back gage
|
| Electrical Description |
|
|
| Comments: |
- used in hvac shop
was $ 108,828.00 new on 12/07
|
|
