Home   |   Contact Us   |   About Us   |   Email NetMachinery  |   Tel: 704-904-9123


Home > NetMachinery Equipment Listings > Manual Lathes
We found 1 matching ad. Now displaying the final ad.

FOR SALE: Year - 1968 Make - Gray Model - Series 60
Mouseover Thumbnails to Enlarge


Price: $129,900 offer USD   
Category: Vertical Turret Lathe (VTL)
Capacity: 84" table x 96" under rail

Ad # 10938

Add/Remove from Checklist
Year: 1968
Make: Gray
Model: Series 60
Condition: Good
Electrical: 460/3Phase

Machine Status:Under Power
Shipping Info:Requires rigger
Weight:
Dimension: L x W x H

Machine Location:
City: On Request
State: North Carolina
Country:
USA

Price:

$129,900 offer USD


Click Here to Print Quote

Buyers Premium:
A 5 % Buyers Premium applies to the final sale price of this item   

General Description
  • table-84"height under sadle-84"
    height under ram face-96" plus
    vert travel-48"
    3" bore in ram head
    max swing-96"
    table top to floor-36"
    overall mach. height-14ft.
    4 axis DRO system-both rams up/down -left
    /right
    pit shown but not required-due to
    building
    height restriction

    Year 1967 or 1968 (not quite sure)

    This information below was copied from
    The G.A.
    Gray Company Bulletin 92.
    It seems accurate. There is more room
    under the rail than specified.

    Machine size 84"
    Table diameter 84"
    Height under saddle 84"
    Height under ram face 92"
    Height under turret face 96"
    Vertical travel (below saddle) of ram
    head
    (std.) 48"
    Vertical travel (below saddle) of turret
    head
    (std) 30"
    Vertical travel of side head above table
    80"
    Horizontal travel of ram head 54"
    Horizontal travel of turret head 57"
    Horizontal travel of side head ram 32"
    Travel past center - ram head 1/2"
    Travel past center - turret head 1/2"
    Travel of rail 74"
    Swivel of ram head either side of
    vertical 45
    degrees
    Size of bore in ram head 3"
    Size of bore in turret head 3"
    Maximum swing, with or without side head
    96"

    Feeds per revolution of table (infinitely
    variable) .002" - .250"
    Table speed range rpm (infinitely
    variable) 0.8 - 194

    Table top to floor 36 1/4"
    Overall height machine top to floor 14' -2"
    Overall height pendant top to floor 18'
    Overall height top of ram to floor 18'

    Two range simple transmission

    12,000 lbs table load
    Automatic lubrication
    Constant surface cutting
    Power indexing turret head
    75 Hp DC table drive
    All heads are DC drive
    Rail head AC drive with self leveling
    feature
    and automatic locking
    There is a box full of gears I suspect
    are for
    thread cutting and drum scoring

    1st I swapped the 5 HP DC drive control
    for the
    ram with the drive on the on the turret
    head. I
    chose to swap drives rather than repair. 2nd
    the
    clutch slips on the turret head when
    raising/lowering the head. We just put it
    into the
    fastest feed to get where we are going in a
    hurry.
    The machine has operated like this for at
    least 8
    years and has never bothered us.
    Everything else works as it should i.e.
    table,
    rail, lube pump, way lube feeders etc
    I believe the machine was made to be floor
    mounted and we installed it in a pit to lower
    the overall height of the machine for (1) hoist
    rail bridge clearance and (2) to keep the table
    height lower. Currently our hoist rail will not
    clear the operator station counterweighted
    davit arm on top of the machine but it really
    does not need to as we only lift machining
    parts – not the Gray’s parts. The pit depth is
    20.5” and the table height to the floor is
    17.5”. If floor mounted it would put the table
    at 38”. Not a bad working height. The 75 HP DC
    motor is mounted on the working floor and is
    belt driven to the table drive sheave in the
    pit. The DC motor is on a separate frame so I
    would think it may just be a matter of some
    shorter belts if both machine and motor were on
    top of the floor.


Purchase Information
To Receive more info via E-mail Click Here
or Phone NetMachinery.com at 704-904-9123 Do You need a Trucking Company? Click Here for Trucking Companies

Disclaimer: Subject to prior sale & verification by buyer.Specifications herein are assumed correct but are not binding in detail.We encourage your personal inspection prior to sale of this machine to confirm accuracy of ad. See Standard Terms And Conditions
Warranty: Machine sold "As is, Where is " buyer inspection encouraged

To Inquire about this machine contact: NetMachinery 704-904-9123
Or Click Request more information

Refer to Ad # 10938 when Inquiring Asking Price: $129,900 offer
Buyers Premium: A 5 % Buyers Premium applies to the final sale price of this item   

This Ad Has Been Viewed 11722 Times.

Print Friendly Ad Popup Loan Calculator Add/Remove from Checklist

 
Modify / Renew Ad | Delete Ad | Lease Application | Add or Remove Photo | View All Ads Posted By This User


01120100-NA


120K offer