0.080 (2 mm) to 1-1/4 (32 mm)
|
Ad Number: 15886
|
Year: 2005 | Make: Rush Machinery | Model: 132C
|
Machine Type: | Condition: Excellent | Price: 2595.00
|
Description: Rush # 132C tool & cutter grinder Grinder was not used as much as we expected, like new. A. Drill & Tool Size Capacities 1. Drill Diameter Range: 0.080 (2 mm) to 1- 1/4 (32 mm) 2. Tool Shanks: Straight Shanks: .080 (2mm) to 1-1/4 (32mm) Morse Taper Shanks: to #4 3. Maximum Drill Length: 14 (356mm); 22 (559mm) with optional spindle extension (P/N SP32). For most drills less than Ύ (19mm) diameter, almost any length can be accommodated. Drills over Ύ (19mm) diameter and over 22 (559mm) long can be ground, in some cases. Contact Rush Machinery regarding specific applications. 4. Maximum Diameter of Tools Other than Drills: 2-1/2 (63mm), with a maximum shank diameter of 1-1/4 (32mm). 5. Maximum Length of Tools Other than Drills: 5 (127mm) excluding the tool shank. B. Basic Drill & Tool Sharpening Capabilities 1. Drill Sharpening (right or left hand) Note: For all left hand tools, optional cams are required. a) Point Angle Range: 40 to 180+ degrees b) Number of Flutes- 2, 3 & 4 c) Flute Types - spiral (slow,standard & fast) and parabolic d) Shank Types - Straight and Morse Taper Nos. 1*, 2, 3 & 4 (* Optional rear steady available). e) Point Types -conventional, split point, lip corrected, web thinned,spiral point*, sheet metal*, double angle, 4-facet, flat bottom,structural steel* & plastic point. (* Optional cam required, see para. .D.8.) f) Step and subland - sharpen point and step 2. Countersink Sharpening (evenly spaced flutes only) Number of Flutes- 1, 2, 3, 4, 5*, 6* (* Optional cam required) 3. Tap Sharpening a) Sharpens the tap chamfer b) Straight flutes (for high spiral taps- bottoming chamfer only) c) Number of Flutes- 2, 3, 4, 5*,6*, 7*, 8* (* Optional cam required) 4. Reamer Sharpening a) Sharpens the reamer chamfer b) Number of flutes-4, 5*, 6*,7*, 8* & 10* (* Optional cam required) 5. End Mill and Counterbore sharpening a) Number of Flutes (End Sharpening) (1) Center cutting- 2 & 3 (2) Non-center cutting- 4 b) On end-grind - Primary, secondary and gash in one setup. c) End Mill O.D. Grinding (any number of flutes) with optional: Air Bearing Grinding Attachment (P/N AB32) A. Grinding Spindle Assembly 1. Wheel Spindle shaft- hardened and ground steel with a standard tapered end for wheel hub mounting(taper- 3 per foot). 2. Sealed and permanently lubricated ball bearings 3. Spindle Housing material - cast iron 4. Spindle motor- ½ H.P., Totally Enclosed Fan Cooled (TEFC), 3450 rpm, 1 phase,115 volts and 60 Hz. Options- 3 phase system, 230/400/460V, 50/60 Hz 1 HP, TEFC motor (P/N MS04). 5. Starter switch- for single phase motor is a manual switch with overload protection. Optional- The Magnetic starter system is used for a 3 phase motor and has overload protection; 115V. output controltransformer and a push button on/off station. 6. Coupling, motor/spindle shaft-keyed, self- aligning splined elastomer type. 7. Protective grinding wheel shroud with hinged cover for easy access a) Steel construction b) Has provision for mounting the optional - Overhead Rush Easy Dress Wheel Dresser (P/N WD01- See optional list in para. III) 8. Grinding Wheels a) Standard - Main wheel: 7 diameter by 1- 1/4 wide aluminum oxide & ceramic blend with 1-1/4 bore b) Optional- Ceramic/aluminum oxide, CBN and diamond wheels of various types - See Rush Price List or contact Rush Machinery for details. B. Cross Slides (X & Y directions) 1. Cast iron 2. Spindle assembly mounts on the cross- slides. 3. Dovetail ways with adjustable tapered gib on each slide 4. Both slides are equipped with Acme screws and bronze nuts 5. An adjustable stop is mounted on the traverse ways to ensure a repeatable centering position during point splitting and other operations. Stop can be quickly disengaged, when not in use. 6. The traverse slide has a calibrated dial with crank. Dial calibrations are to 0.002 7. In-feed slide has a calibrated dial with crank. Dial calibrations are to 0.001 Note: Optional- Millimeter dial calibrations (6. & 7. above) available. 8. Metal and accordion type dust covers protect the ways. C. Machine base 1. Cast iron 2. Provides mounting for the cross-slides and the workhead D. Work head 1. Machined cast aluminum- main body and gear cover with cast iron work head base. 2. Work holding Chuck 4-3/8 (111 mm) O.D.- self centering, with 6 precision and hardened steel jaws with holding length of 2-3/8 (60 mm), Meehanite body and hardened steel scroll plate, chuck work holding diameter range- 0.080 (2.0 mm) to 1.260 (32 mm). 3. Chuck spindle- hollow, hardened and ground with 1.50 (38mm) diameter bore. Spindle provides 12 index slots for index grinding. 4. Chuck spindle and cam rotation drive uses machined gears in a covered housing. Drive source is a hand crank, or geared-head air motor. 5. The work head has a tilting adjustment, 0 to 15 degrees, which allows grinding above the wheel centerline for the proper angle for point splitting, web thinning and end mill end grinding and other applications. 6. The spindle bearing is a large diameter precision rotary- linear ball bearing which provides anti- frictional motion in both rotational and linear directions. 7. The spindle and cam rotational drive system uses hardened and ground gear shafts with radial and thrust anti- friction needle bearings. Gear ratio/s between the cam and workhead spindle rotation are 2:1 for even number of flutes and 1:1 for odd number of flutes. 8. Cam action- provides controlled spindle forward/back axial motion for a variety of grinding requirements including grinding left hand (LH) & right hand (RH) tools. a) All cams are surface hardened. b) Cam followers are ball bearing roller type c) Cams can be changed in 5 to 10 seconds without tools. d) Cams available: |
|