User SearchYour search results (if any) appear below in groups of 75 for each section.
Brakes
We found 2 matching ads. Now displaying the remaining 2 ads.
Year |
Make |
Model |
Condition |
Price |
Details |
|
Ad # 11235 | Press Brakes (Hydraulic) |
2006 |
Betenbender |
6-50T |
Very Good |
sold |
No Photo /
More Info. |
50 ton x 6ft: 50 Ton x 6ft
programable back press
** MADE IN THE U.S.A. **
BETENBENDER HYDRAULIC PRESS BRAKE QUOTE
Model 6' x 50 Ton
SPECIFICATIONS:
Maximum Tonnage ......................... 50 Tons
Maximum Bending Length .................. 72 inches
Maximum Stroke Length ................... 8 inches
Open Height ............................. 14 inches
Closed Height . . . . . . . . . . . . . . 6 Inches
Throat Depth ............................ 8 inches
Distance Between Housings ............... 54-1/2 inches
Ram Repeatability ....................... +/- .002"
Hydraulic Pressure ...................... 2500 lbs.
Hydraulic Oil Capacity .................. 31 Gallons
Machine Weight .......................... 6,800 lbs.
Machine Dimensions:
Overall Height ................. 104 inches
Overall Length ................. 87 inches
Overall Width .................. 45 inches
Bed Height .............................. 28 Inches
Motor Horsepower ........................ 10
ACCURACY
Every Betenbender machine is thoroughly inspected and tested.
1.Parallelism is maintained between bed and ram or at preset
angle by using precision automatic leveling controls. Parallelism
is maintained at +/-.002" in low speed.
2.The ram bottom reversal point is controlled by precise limit
switches referenced off the bed. This isolates housing deflections, which can interfere with its accuracy.
Enhanced Productivity
Return speeds and rapid advance facilitate high cycle rates.
Operator control is simplified by slow and press speed, thus work
spoilage is avoided. Rapid advance with automatic change. The point
of speed change is fully adjustable by electric limit switch.
Micrometer type tilt adjustment is graduated in .001" increments
permitting ram tilt adjustments up to 1/2" in either direction.
ELECTRO MECHANICAL STROKE CONTROL is bed referenced.
Bottom limit is manually set with a lead screw and displayed by an mechanical readout calibrated in .001" increments.
VERSATILITY
BETENBENDER'S press brakes have long full tonnage strokes,
adjustable length and selectable speed combinations, adjustable
height for short stroke, 2-speed standard and the optional 3- speed for adjustable low speed to prevent whip.
ELECRICAL EQUIPMENT
Meets requirements of NFPA no.79, JIC and construction requirements of the latest ANSI B-11.3 Standards. Includes drip-proof, continuous duty 45 degree Celsius ambient hydraulic pump motor wired for 230 or 460 volt, 3 phase 60 hertz.
DEPENDABILITY
Self-lubricating replaceable non-metallic ways prevent galling and provide long service life. Cylinders are high-strength, all steel. To minimize wear and provide a superior oil seal, inside
cylinder surfaces are honed to a mirror finish.
Compact, precision machined aluminum manifold incorporates off-the shelf components, minimizes piping and consolidates "O" ring
mounted valves.
Quiet, vane type constant volume pumps. In keeping with good hydraulic design practice, these energy efficient pumps are located outside the reservoir.
Filtration of contaminants as small as 10 microns is accomplished
with intake and discharge filters. A built-in magnetic trap and air breather filter provide added protection against contaminants. Reservoir of large capacity facilitates effective heat dissipation. A fluid level gauge is provided.
CONTROL
Main Control Cabinet - NEMA 12 enclosures mounted in the right housing containing: magnetic non-reversing motor starter and 120 volt circuit.
Main motor START button and STOP button are illuminated.
RAM UP and RAM DOWN buttons.
RUN/JOG Switch.
Fusible disconnect.
MAINTENANCE
Clevis mounted cylinders eliminate cylinder binding by reducing the possibility of oil leaks from cylinder binding. (Pins & bushings do not rotate under load, this reduces excessive wear)
STANDARD EQUIPMENT
Clamp Type Backgauge-Manual American-Made Motor
Adjustable x,y,z All Steel Construction
Depth Stop w/Readout Two Speed Ram
Hour Meter All Hydraulic Fluid Included
Three Position Foot Pedal Disconnect Switch
NEMA Electrics Bottom Time Delay
BET650T
Standard Press Brake Equipment
Clamp Type Backgauge� Manual Adjustable X, Y, & ZAmerican Made Motors
Two Speed RamHour Meter
Bottom Time DelayNema Electrics
Three Position Foot PedalAll Hydraulic Fluids Included
Depth Stop w/Digital ReadoutDisconnect Switch
Three Speed (95T and Larger)All Steel Construction
|
|
Ad # 11234 | Press Brakes (Hydraulic) |
1998 |
Amada |
NC9-EX2-P |
Very Good |
sold |
Photo /
More Info. |
35 tons x 48": Year: 1998
Capacity: 35 Tons
Table length: 47.3 in
Max bending length: 49.3 in
Distance between upringhts: 40.2 in
Throat depth: 7.88 in.
Length of stroke: 3.94 in
Open height: 14.58 in.
|
|
We found 1 matching ad. Now displaying the final ad.
Year |
Make |
Model |
Condition |
Price |
Details |
|
Ad # 11233 | Turret Punch Presses-CNC |
1997 |
Amada |
Pega 304050 |
Very Good |
sold |
Photo /
More Info. |
30 Ton, 58 stations, FANUC Contol: Year: 1997
Accuracy (+/-) 0.005
No of stations: 58
Turret speed: 30 rpm
CONTROL: FANUC PRESS CAPACITY 3o TON TYPE OF PUNCHING FORCE HYDRAULIC X AXIS TRAVEL 50" Y AXIS TRAVEL 39.370" Strokes per minute: 350NUMBER OF TURRET STATIONS 58
|
|
View Detailed Ads
Content copyright © 2011 NetMachinery.com. All rights reserved.
Please send your questions, comments, or bug reports to the Webmaster.
Website Hosting & Development by IndSite.
|
|