User SearchYour search results (if any) appear below in groups of 75 for each section.
Manual Lathes
We found 11 matching ads. Now displaying the remaining 11 ads.
Year |
Make |
Model |
Condition |
Price |
Details |
|
Ad # 4325 | Ram Type & Saddle Type Turret Lathes |
67? |
Gisholt |
2-L/13W-9137 |
Good |
sold |
Photo /
More Info. |
Heavy Duty Turret Lathe: Swing: 24"
Distance Between centers: 60"
Spindle Bore: 4.25"
4 way toolpost
notes:below
air gap and a chuck at 22” and 24”
diameters.
The
22” clears the ways and the 24” would hit
the
ways. It also shows the dimension from
center
of
the chuck to a level point across the
ways.
Dimensions:
The total distance outside the ways is
17”
(his
was 15”). The operator side way is 4 ½”
across.
The opposite side way is 3” across. The
‘air’
between the ways is 9 ½” (his was 7 ½”).
The
ways
are 1 ¼” thick.
The center of the chuck to level across
the
ways
is 11”. The swing is debatable… 22”
definitely
clears the ways. A circle drawn at chuck
center
point could be a little less than 24”
before
touching the ways considering the ‘air
gap’ is
also on center.
Voltage:
575 3 phase… The drive motor, rapid
traverse
motor and coolant pump most likely can be
rewound
for 230/460. There is a small multi-tap
control
transformer inside the control cabinet. It
is
wired for 575 but has the connections for
230
and
460 as well.
Condition:
I don’t know if it runs. The headstock
and
rapid
traverse oil site gauges show ‘middle’ of
the
sight glass bulls eye.
Manual etc.
I have a manual and what looks to be a
complete
electrical print.
Other stuff:
It has a ‘chuck’ switch and ‘inch’
switch.
This
is used on our other Gisholts to maneuver
the
chuck so as to insert the chuck wrench.
loading fee: $ 800.00
|
|
Ad # 10938 | Vertical Turret Lathe (VTL) |
1968 |
Gray |
Series 60 |
Good |
sold |
Photo /
More Info. |
84" table x 96" under rail: table-84"height under sadle-84"
height under ram face-
96"
plus
vert travel-48"
3" bore in ram head
max swing-96"
table top to floor-36"
overall mach. height-
14ft.
4 axis DRO system-both
rams up/down -left
/right
pit shown but not
required-due to
building
height restriction
Year 1967 or 1968 (not
quite sure)
This information below
was copied from
The G.A.
Gray Company Bulletin 92.
It seems accurate. There
is more room
under the rail than specified.
Machine size 84"
Table diameter 84"
Height under saddle 84"
Height under ram face
92"
Height under turret face
96"
Vertical travel (below
saddle) of ram
head
(std.) 48"
Vertical travel (below
saddle) of turret
head
(std) 30"
Vertical travel of side
head above table
80"
Horizontal travel of ram
head 54"
Horizontal travel of
turret head 57"
Horizontal travel of
side
head ram 32"
Travel past center - ram
head 1/2"
Travel past center -
turret head 1/2"
Travel of rail 74"
Swivel of ram head
either
side of
vertical 45
degrees
Size of bore in ram head
3"
Size of bore in turret
head 3"
Maximum swing, with or
without side head
96"
Feeds per revolution of
table (infinitely
variable) .002" - .250"
Table speed range rpm
(infinitely
variable) 0.8 - 194
Table top to floor 36
1/4"
Overall height machine
top to floor 14' -2"
Overall height pendant
top to floor 18'
Overall height top of
ram
to floor 18'
Two range simple
transmission
12,000 lbs table load
Automatic lubrication
Constant surface cutting
Power indexing turret
head
75 Hp DC table drive
All heads are DC drive
Rail head AC drive with
self leveling
feature
and automatic locking
There is a box full of
gears I suspect
are for
thread cutting and drum
scoring
1st I swapped the 5 HP
DC
drive control
for the
ram with the drive on the
on
the turret
head. I
chose to swap drives rather
than repair. 2nd
the
clutch slips on the turret
head when
raising/lowering the head.
We just put it
into the
fastest feed to get where
we
are going in a
hurry.
The machine has operated
like this for at
least 8
years and has never
bothered
us.
Everything else works as
it should i.e.
table,
rail, lube pump, way lube
feeders etc
I believe the machine was
made to be floor
mounted and we installed it in
a pit to lower
the overall height of the
machine for (1) hoist
rail bridge clearance and (2)
to keep the table
height lower. Currently our
hoist rail will not
clear the operator station
counterweighted
davit arm on top of the
machine
but it really
does not need to as we only
lift machining
parts – not the Gray’s parts.
The pit depth is
20.5” and the table height to
the floor is
17.5”. If floor mounted it
would put the table
at 38”. Not a bad working
height. The 75 HP DC
motor is mounted on the
working
floor and is
belt driven to the table drive
sheave in the
pit. The DC motor is on a
separate frame so I
would think it may just be a
matter of some
shorter belts if both machine
and motor were on
top of the floor.
|
|
Ad # 15970 | Vertical Turret Lathe (VTL) |
|
Bullard |
56" Dynatrol |
Good |
sold |
Photo /
More Info. |
56" table dia: Bullard 56 dynatrol VTL
56" Bullard Dynatrol Vertical Turret
Lathe.
56'' table
66" swing
? under rail
6-jaw chuck
3 heads including a side head. |
|
Ad # 16178 | Heavy Duty Large Lathe 24in. & over swing |
1977 |
American |
2516-27 x 216 |
Fair |
sold |
Photo /
More Info. |
40" x 18ft: American manual lathe # 2516-27 x 216
center distance: 216" or 18ft
swing over bed: 40" ,over cross slide: 30"
chuck: 6 jaw 24" dia
12" steady rest
2.5" spindle bore
voltage: 575/3
CATALOGUE STD. SPECIFICATIONS:Hole Thru Spindle
2.5"Swing Over Bed Ways, Rated 40"Swing Over
Bed
Ways,30"Swing Over Cross-Slide
Distance Between Centers 216";Cross-Feed Travel
6"; Tailstock, Spindle Diameter 5"ailstock,
Spindle Travel 12";Tailstock, Spindle Taper #5
MT;(27) Spindle Speeds, Range 12 to 800 RPM(66)
Carriage Longitudinal Feeds .0025 to .1506
IPR(66) Thread Changes, Range 1 to 60 TPI Motor
Horsepower 40 |
|
Ad # 10660 | Hollow Spindle/Big Bore Engine Lathes |
93 |
Poreba |
TPK 90A-1/3M |
Good |
SOLD |
Photo /
More Info. |
36" x 132" w/-4.5" spindle bore: 36" swing over ways
132" centers
24" 6 jaw chuck
tool post
2-steady rests
2-speeds on tale stock
inch/metric threads
power rapid travers
36" swing
28" swing over cross slide
4.5" thru hole
std specs below-please verify
Capabilities
Swing over bed 36 1/2"
Swing over gap 49"
Swing over cross slide 25"
Distance between centers ~ 118" or maybe 120"
Headstock
21 spindle speeds 9, 11, 14, 18, 22, 28, 35 1/2,
45, 56, 71, 90, 112, 140, 180, 224, 280, 355, 450,
560, 710, 900
Workpiece weight between centers 13,500 lbs.
Workpiece weight with 2 steady rest 20,000 lbs
Hole through spindle 3 3/4"
American standard direct mount spindle nose
A1-11
Chuck
24" Buck 6 jaw chuck
Feeds and threads
Longitudinal (70) ..0043 - .500 IPM
Cross feed range (70) .0021 - ..250 IPM
Top slide feed range (70) .001 to .125 IPM
Metric threads range 1 - 120 mm/rev.
Inch threads range 1/4 - 30 TPI
Carriage and apron
Cross slide travel 18 1/2"
Top slide travel 11 3/4"
Carriage length bearing bedways 33 3/4"
Carriage bridge width 16 1/2"
Rapid travels
Carriage 260 IPM
Cross slide 130 IPM
Top slide 65 IPM
Six way power feeds/spindle locked standard
Reverse feed direction no spindle direction
change standard
Carriage rear mount chip and coolant splash
guard standard
Tailstock
Quill diameter 5 1/8" with tang slot
Quill travel 11 3/4"
Quill taper No. 6 MT
Two speed quill travel 1:1 and 1:5 ratio
Miscellaneous
Main drive motor 2 speed AC 23 and 36 HP
Width of bed x depth 23" x 17 3/4"
Length = between centers + 8 feet
Width 7 feet
Net weight 19,400 lbs
Electrical
U.L approved
460 volt 3 phase 60 Hz
Standard equipment included
Coolant system
Automatic headstock lubrication
8T slotted top slide
Six way power rapid traverse
Chuck splash guards
Spindle positive lock at 5 degree increments
Longitudinal and cross slide limit switches
Ammeter
Optional equipment included with it
Steady rest 1 37/64" - 15 3/4" roller
Steady rest 15 3/4" - 23 1/2" roller
Live center 6MT
Quick change tool block with holders
Digital read out
|
|
Ad # 10661 | Tool Room Lathe 8in. to 14in. swing |
90,s |
Logan Powermatic |
1120003-TH |
Very Good |
sold |
Photo /
More Info. |
12x30: 8"-3jaw chuck
light
12"swingx30" |
|
Ad # 10662 | Tool Room Lathe 8in. to 14in. swing |
90,s |
south bend |
model 400 |
Very Good |
sold |
Photo /
More Info. |
12x36: 2"thru hole
10"-3jaw chuck
12" over ways
15" over crosss slide
quick ckange tool post
steady rest
coolant
light
2 spd. motor
taper attach. |
|
Ad # 10590 | Vertical Turret Lathe (VTL) |
|
Bullard |
46" cutmaster/# 75 |
Needs Work |
sold |
Photo /
More Info. |
46" bullard cut master: 46" cut master-std specs please verify
Capacity: 46"
Motor: 40 HP 6.1-187 RPM
Under Rail: 48 in. Under Adjustable Rail
Features:
* 3 Jaw Chuck
* Adjustable Rail
* Side Head
* Square Turret
* Pendant Control
* Coolant
Table Diameter ........................ 46"
Maximum Swing W/Side Head ............. 52"
Maximum Swing Without Side Head ....... 59"
Max. Height Under Rail ................ 44"
Turret Stroke ......................... 30"
Table Speeds .......................... 6.8-250 RPM
Feeds ................................. .006-.125 IPR
Machine Weight ........................ 45,000 Lbs
EQUIPPED WITH:
4-Position Square Turret
Side Head
no threading capability
have some machine prints |
|
Ad # 16158 | Heavy Duty Large Lathe 24in. & over swing |
90s ? |
Poreba |
TPK 90A1/3M |
Good |
sold |
Photo /
More Info. |
36"swing x 120"centers: Poreba # TPK 90A1/3M Lathe:
Std. Mfg specs below-please verify actual
machines..
36"swing x 120"centers
24" Dia 6 jaw chuck shown and few other
Acc.not shown in pix..steady rest,chuck?
DRO-2 axis included
Std. Mfg specs below
SPECIFICATIONS:
SWING OVER BED: 36 1/2" (927 mm)
SWING OVER CROSS SLIDE: 25"
SWING IN GAP: 49"
LENGTH OF GAP: 17"
DISTANCE BETWEEN CENTER: 120" (3048 mm)
SPINDLE BORE: 3 3/4"
SPINDLE NOSE: A1-11
SPINDLE MOTOR: 20/30 HP
SPINDLE SPEEDS (2 RANGES): 7.1-710 RPM
FEEDS - LONG. (122): .0043-.5 IPM
- CROSS (122): .0021-.25 IPM
- TOP SLIDE: .001-.125 IPM
THREADING - INCH 1/4-30 TPI
- METRIC: 1-120 MM/REV
CROSS SLIDE TRAVEL: 18 1/2"
TOP SLIDE TRAVEL: 11 3/4"
RAPID TRAVERSE - LONG./CROSS: 260/130 IPM
- TOP SLIDE: 65 IPM
TAILSTOCK - DRILLING, DIAMETER: 5 1/8"
- DRILLING LENGTH: 40"
- TAPER: #6 MT
- TRAVEL: 11 3/4"
ELECTRICS: 440V/3Ph/60hZ
|
|
Ad # 143 | Ram Type & Saddle Type Turret Lathes |
1955 |
Gisholt |
Turret Lathe 13W-9136 |
Fair |
sold |
Photo /
More Info. |
Large 25" Turret Lathe w/ Tooling: Large 6 station Turret Lathe
Swing 25" over ways
18" chuck-3-jaw w/T-slot
Length 5'from chuck to turret
Misc Tooling
4" spindle bore |
|
Ad # 14539 | General Purpose Lathe 15in. to 23in. swing |
? |
Leblond |
regal |
Good |
sold |
Photo /
More Info. |
18" x 78": leblond regal manual lathe
swing over bed-18" swing over cross slide: 12"
center distance:80"
taper attachment
3 jaw chuck 12"
spindle bore 2-1/4"
english threading only
work light
coolant spindle RPM: 38-1500
chuck guard |
|
We found 1 matching ad. Now displaying the final ad.
Year |
Make |
Model |
Condition |
Price |
Details |
|
Ad # 16171 | Vertical Machining Centers (VMC) |
1992 |
Enshu |
650W & 650VX |
Good |
sold |
Photo /
More Info. |
Table Size: 25.6" X 78.7": Enshu # 650W & 650VX vertical machining centers
Note: std mfg specs below please verify
actual machines-2 machines available
Enshu EV-650 CNC 50-Taper CNC Vertical
Machining Center
Equipped With:
ENAC (Fanuc 15M) CNC Control, Remote
Jog Handwheel, 6000 Max RPM Cat-50 Taper
Spindle, 30 Station Side-Mount Twin-Arm Tool
Changer, Diakin Inverter Spindle Chiller,
Coolant System with Tank & Pump, Rear Chip
Auger, RS-232 Port, Machine Manuals & Schematics
as Shown, Large Assortment of Enshu tooling
Table Size: 25.6" X 78.7"
Machine Travels (X/Y/Z): 63" x 25.6" x 26"
Table Capacity: 3300 Lbs.
Spindle Taper: Cat 50
Spindle Speeds: 6,000 Max RPM
Transmission: Stepless
Rapid Traverse Rate (X/Y/Z): 787.4 IPM (X
and Y) 590.6 IPM (Z Axis)
Maximum Cutting Feed Rate: 393.7 IPM
Tool Changer Style: Side-Mount, Twin-Arm
Tool Changer Capacity: 30 Stations
Tool Change Time: 2.5 Sec
Max Tool Length: 15.7"
Max Tool weight: 33 LBS
Spindle Drive: 20 HP
Spindle To Table Distance: 7.9" - 33.9"
Spindle Center to Column Distance: 26.4"
Enshu 650VX Vertical Machining Center with
Fanuc 15M Control
Equipped With:
Fanuc 15M CNC Control, 30-Position Tool
Changer, Spindle Chiller, RS232 Port, Remote Jog
Hand Wheel, Table Guarding
Description:
Vise and Tool Holders NOT Included
Manufacturer: Enshu Model: 650VX Year: 1995
Serial Number: 339
Main Unit Approx Weight: 0.00 lbs
Main Unit Dimensions (in inches): Length:
193.00" Width: 168.00" Height: 122.00"
Components:
Coolant Tank: Length: 54.00" Width: 40.00"
Height: 29.00"
Specs:
Machine Control: Fanuc 15M
Table Size: 78.7" x 25.6"
Machine Travels (X/Y/Z): 63" / 25.2" / 26"
Spindle Taper: Cat 50
Spindle Speeds: 6000 RPM
Tool Changer Style: Twin Arm
Tool Changer Capacity: 30
Note: a few misc holders included as pictured
in tool changer |
|
We found 3 matching ads. Now displaying the remaining 3 ads.
Year |
Make |
Model |
Condition |
Price |
Details |
|
Ad # 10841 | Horizontal Boring Mills |
1988 |
G and L |
G50-T |
Good |
Sold |
Photo /
More Info. |
Table 48" x 96": Giddings & Lewis Horizontal Model G50-T year 1988
Capacities:
Spindle diameter 5"
Spindle taper #50 (CAT 50)
Spindle speed (infinitely variable) 14 - 3000 Rpm
Spindle travel 36" (Z axis)
Headstock travel on column 96" (Y axis)
Table size 48" x 96"
Table cross travel 96" (X axis)
Table load capacity 35,000 lbs. plus (some documentation states 40,000 and some 44,000)
Bed length 72"
Saddle travel 38" (W axis)
Features:
Pre-loaded anti-friction ball screws on all linear axis
Inductosyn feedback W, X, and Y
Resolver feedback Z axis
Infinitely variable spindle speeds 4 ranges (4 speed transmission)
Power drawbar
Lubri-Cool (Hansen) unit for headstock lube system
High pressure flood coolant (through the spindle and external)
G&L NumeriPath CNC 8000B control
Spindle drive (MTDC) 30 HP
Control cabinet voltage 480, 3 phase 60 hertz (We are actually 600 3 phase with a local transformer)
Allen-Bradley information. The W, X, Y and Z all use the same components.
Bulletin 1326 AC Servo Motor
Volts: 230 3 phase
Frequency: 0 – 250 Hz
Serial No.: 28321
Catalog No.: 1326AB-C3E-11-2287B
Part No.: 126882
Date Code: 0106
Max Cont Output Power: 7.5 Kw @ 40 degrees C
Max Speed: 3000 RPM @ 40 degrees C
Max Const.: Stall Torque 310.0 Nm/Lb. In. @ 40 degrees C
Max Const.: RMS amperes 49.1 @ 40 degrees C
Term. Resistance: 0.055 ohms @ 25 degrees C
Brake: None
Bulletin 1391 Controller
1391B-AA45 series D
Serial No: 07487
GE spindle DC drive information
General Electric DC 300 adjustable speed drive
|
|
Ad # 16163 | Manual Mill, Parts and Accessories |
|
|
|
Good |
sold |
Photo /
More Info. |
turn tables: turn tables
4ft x 4 ft and larger and smaller |
|
Ad # 142 | Horizontal Mills |
1954 |
K & T |
10HP-2CK |
Fair |
sold |
Photo /
More Info. |
Horiz-Vert mill : Horiz mill w/ vert attachment |
|
We found 2 matching ads. Now displaying the remaining 2 ads.
Year |
Make |
Model |
Condition |
Price |
Details |
|
Ad # 10587 | Single Spindle Drill Press |
1994? |
T-Drill |
T-150/type-0242 |
Good |
sold |
Photo /
More Info. |
T-Drill: T-Drill
# T-0150
Includes some misc tooling |
|
Ad # 10583 | Radial Drill Press |
1977 |
South Bend |
MX 75/2500 |
Very Good |
sold |
Photo /
More Info. |
20" dia column x 8 ft arm..VERY LARGE: 20" Dia Column
8 ft arm-96"
rapids
coolant
20 HP motor
5MT spindle
20-1600vrpm
T slot std box base 39-3/8" x 29-1/2" x 19"-1000lbs
also includes a 0-90 deg (one way) box tilt table-T-slotted 39-3/8" x 29-1/2" x 25-1/2"-1500lbs
made in Spain-Quality
updated additional specs below-please verify
Model South Bend (Foradia made in Spain and still in business) MX 75/2500 SN# 740003
Column dia. 21 5/8"
Arm Length 8' 3-3/4"
Spindle HP 12
Drill capacity mild steel 3"
Drill capacity cast iron 3-1/2"
Tapping mild steel 3"
Tapping cast iron 3-9/16"
Morse taper No. 5
Spindle nose dia. 3-9/16"
Spindle traverse in head 15-3/4"
Number of spindle speeds 16
Spindle speed range 4--1600
Number of spindle feeds 12
Range of feeds per revolution .0029" - .0393"
Maximum drilling pressure 6300 Lbs.
Maximum spindle torque inch/lbs. 5425
Maximum spindle radius center of column to center of spindle 110"
Minimum spindle radius center of column to center of spindle 27-3/8"
Horizontal traverse of head on arm 82-3/4"
Maximum distance spindle to base 80-11/16"
Minimum distance spindle to base 80-11/16"
Maximum height of column above floor 141-1/2"
Maximum height of head above floor 150"
Base working surface 107-5/8" x 45"
Base height 11-3/4"
Base dimensions 142-3/4" x 45-1/2"
Number of 7/8" T slots 3
Elevating arm motor HP 3
Coland pump HP 1/2
Net weight 22,708 lbs. not including box table and tilting table
I believe the tables are as follows
Box table:
39-3/8" x 39-3/8" x 19-3/4 high with 5/8" T slots
Vertical and horizontal T slots
Tilting table:
39-3/8" x 39-3/8" x 25-1/2" high with 5/8" T slots
3 T slots on top face. Worm gear rotation through 90 degrees. Graduated scale.
|
|
We found 3 matching ads. Now displaying the remaining 3 ads.
Year |
Make |
Model |
Condition |
Price |
Details |
|
Ad # 10949 | Vertical Band Saws |
|
Marvel |
8m8 |
Good |
sold |
Photo /
More Info. |
: 1" blade width
tilts 45deg. either direction
18" throat
|
|
Ad # 10950 | Vertical Band Saws |
|
DoAll |
36-R |
Good |
sold |
Photo /
More Info. |
36" tilt table: 36" throat
tilt table
550/3 elect.
variable speed 30x60 table
21" height opening |
|
Ad # 10944 | Tilt Frame Vertical Band Saw |
|
Marvel |
8-M4 |
Good |
sold |
Photo /
More Info. |
: runs good
tilts 45deg. either direction
18" throat
1" blade |
|
We found 5 matching ads. Now displaying the remaining 5 ads.
Year |
Make |
Model |
Condition |
Price |
Details |
|
Ad # 15971 | Pedestal & Bench Grinders |
|
grand rapids |
DW-8 |
Fair |
sold |
Photo /
More Info. |
: Grand Rapinds DW-8 -drill grinder |
|
Ad # 15969 | Tool & Cutter Grinders |
1996? |
K.O.Lee |
B2062H |
Good |
sold |
Photo /
More Info. |
table size:5-1/4" x 37-1/4": KO Lee B2062H #tool & cutter grinder
dtocks:32"
distance between centers in workhead
and tailstock:26"
table size:5-1/4" x 37-1/4"
sub table:8 x 48"
cross movement:7-1/4"
table traverse"20"
vert column movement:7"
column dia:4"
mores specs
at:http://vintagemachinery.org/pubs/1738/6596.pd
f
|
|
Ad # 15968 | Tool & Cutter Grinders |
1997 |
Giddings & Lewis |
940 |
Good |
sold |
Photo /
More Info. |
: Giddings & Lewis 940 Tool Sharpener w/Coolant
Pump & Dust Collector, model HC, approx.
footprint of 42" x 70" x 100" tall, 460V, 3ph
Exactamatic #HC, grinder, .0625" min to 1"
maximum drill capacity
std mfg specs below-please verify actual
machines
Drill Capacity:1/16" X 1"
Drill Length:12"
Travel:4"
Horizontal Mounted Ultra Precision Point
Concentric:0.0002"
Point Drill Degrees Included Angles:60 To 140
Degree
Grinding Wheel Size:12" X 5"
Grinding Wheel Width:1"
Grinding Wheel Motor:3/4 Hp.
Grinding Wheel Speed:1,800 Rpm's
Work Head Motor:1/4 Hp
Work Head Speeds:1,800 Rpm's
Coolant Motor:1/8 Hp
Coolant Tank:7-1/2 Gallon
Coolant:Yes
Guards:Yes
Drill Holder:Yes
Dust / Mist Collector:Yes
Drill Splitter:Yes
Drill Bushing Index Plates:Yes
Drill Holders With Collects:Yes
Grinding Wheel Built-In Cam Former Wheel
Dresser:Yes
Self Contained Automatic Lubrication System:Yes
Point & Angle Can Be Varied By Work Head
Angular
Adjustment:Yes
Over All Dimensions:24" X 30" X 46" H
Weight:1,875 Lbs. |
|
Ad # 15967 | Tool & Cutter Grinders |
|
Oliver of Adrian |
600 |
Good |
sold |
Photo /
More Info. |
1/2"-3-4" drill capacity: Oliver of Adrian large drill sharpner # 600
voltage: 440/3
hp:1.5
The Oliver Model 600 Drill Point Grinder is
the ideal machine for sharpening large diameter
bits from 1/2" to 3" (76 mm), with the option
to
increase the maximum drill size to 4" (102 mm).
The machine easily handles two flute, three
flute and four flute drill bits. Variable
included point angels are readily obtained and
variable clearance or lip relief angles can be
dialed in. The geometry that is best suited for
your manufacturing procedures can be added to
your drills easily and quickly.
A revolving chuck and oscillating grinding
wheel spindle are coordinated with a direct
gear
positive drive. All of the movements involved
with sharpening are automatic.
The Model 600 Automatic Drill Grinder is
supplied with an airdraulic infeed unit that
allows the operator to select the rate of
infeed
and the total amount of stock removal. This
feature, combined with the automatic grinding
cycle, permits the unit to function without an
operator once the loading and operating
sequence
has been completed. This eliminates the chance
of operator error that comes with swing
grinding
large bits. The machine is also supplied with a
tank, pump, splash guards and piping to provide
coolant to the grinding area.
Heavy duty, powerful and rigid machine
Easy to use with minimal training
required
Covers a wide range of applications
Longer lasting drills with burr-free
holes
Base model grinds 1/2” to 3” diameter
drills (2 sets of jaws)
Grind from 1/4" to 4” diameter drills
with
optional 4 sets of jaws
Superior wall finish
Compatible with spade, parabolic and
twist
drills
The Oliver 600 creates a precision helical
drill point, which provides superior
penetration
and longevity in comparison to a point created
by a typical "swing grind" style grinder. In
many applications, the Oliver helical point
reduces the torque and thrust required by over
20%, resulting not only in a longer lasting
bit,
but a longer lasting drill machine as well due
to less wear and tear. More holes drilled per
grind means less downtime that can result in a
substantial cost savings. This heavy duty,
powerful and rigid grinder will cover a wide
range of applications and provide many years of
reliable service.
|
|
Ad # 16173 | Tool & Cutter Grinders |
1996 |
Giddings & Lewis |
HC/17822M |
Good |
sold |
Photo /
More Info. |
1/16"-1.5": G & L # HC exactamatic Helical point drill
grinder
Std mfg specs below -please verify actual
machines
specifications:
Helical1/16" to 1-1/2" (1.55 to 38.0 mm)
Wide-Web Helical1/16" to 1-1/2" (1.55 to 38.0
mm)
Bickford*1/8" to 1" (3.0 to 25.4 mm) -
*Requires two operations to achieve geometry
Racon1/8" to 1" (3.0 to 25.4 mm)
Conventional1/16" to 1" (1.55 to 25.4 mm)
Step drills3/32" to 1/2" (2.4 to 12.5 mm)
3- and 4-fluted drills1/16" to 1-1/2" (1.55
to 38.0 mm)
2, 3 and 4 straight-fluted plug and bottom
taps#4 to 7/8" (M3 to M22)
Grinding wheelHorizontally mounted; 20" (510
mm) diameter
Spindle power3 HP (2.25 kW), 1800 RPM
CNC Controlyes
Dimensions92" x 102" (2.34 x 2.59 m) plus
coolant tank
Weight3200 pounds
|
|
We found 1 matching ad. Now displaying the final ad.
Year |
Make |
Model |
Condition |
Price |
Details |
|
Ad # 16166 | Keyseaters |
60s |
Mitts & Merril |
# 2 Hyd |
|
sold |
Photo /
More Info. |
: Mitts & Merrill hyd. Keyseater #2 Hydraulic
std mfg general specs below-please verify
actual machines
GENERAL SPECIFICATIONS
Maximum Keyway Length: 12"
Maximum Keyway Width: 1-1/4"
Largest Standard Post: 2-3/8"
Largest Bore Possible to Keyway: 6"
Height Floor to Table: 35"
Cutting Speed: 16 ft. per min.
Return Speed: 32 ft. per min.
Feed, Automatic: .002" to .010"
Table Size: 16" x 16" |
|
We found 1 matching ad. Now displaying the final ad.
Year |
Make |
Model |
Condition |
Price |
Details |
|
Ad # 16159 | Lapping & Polishing Machines |
|
SpeedLap |
SNF-24BTW |
Good |
sold |
Photo /
More Info. |
: Speedlap 24
lapping machine |
|
We found 2 matching ads. Now displaying the remaining 2 ads.
Year |
Make |
Model |
Condition |
Price |
Details |
|
Ad # 16162 | Miscellaneous / Other |
|
Tooling |
|
Good |
sold |
Photo /
More Info. |
lots of misc tooling: Misc totes of all types of machine shop tooling
clamps
lathe cutters
milling
|
|
Ad # 16160 | Miscellaneous / Other |
|
Acorn table |
5 x 5 |
Good |
sold |
Photo /
More Info. |
5 x 5ft : Acorn welding fixturing tables
Note:no legs for it,slight machining groove
on sides of top
size approx 5ft x 5ft |
|
We found 4 matching ads. Now displaying the remaining 4 ads.
Year |
Make |
Model |
Condition |
Price |
Details |
|
Ad # 16172 | Misc. Sheetmetal Equip. |
|
ransome |
E8760 |
Good |
sold |
Photo /
More Info. |
: Ransome tube/tank Turning rolls
84" dia max
several other sets available-must see |
|
Ad # 16170 | Misc. Sheetmetal Equip. |
|
Pullmax |
X8 |
Good |
sold |
Photo /
More Info. |
: Pullmax X-8 beveler unit
std.mfg specs below-please verify actual
machines
MODEL ................................ X8
MAXIMUM V-GROOVE DEPTH (MILD STEEL) .. 3/8"
MAXIMUM V-GROOVE DEPTH (STAINLESS) ... 9/32"
CUTTING SPEED ........................ 6 TO 11
FPM
ANGLE OF BEVEL ....................... 37-1/2
DEGREES
MAXIMUM MATERIAL THICKNESS ........... 2"
MAIN MOTOR ........................... 2-1/2hp
voltage wired 575/3 |
|
Ad # 10588 | Crimping, Beading & Flanging Machines |
1977 |
Blue Valley |
9-227 |
Good |
sold |
Photo /
More Info. |
1" thick Mtl capacity: Head Knuckling flanger
main drive motor 50hp 575 vlts 3 phs. 1650 rpm
hyd. unit 5hp-- 575 vlt 3phs. 1750 rpm
tooli1"r,2"r,2 3/4 r, 3 1/2r,4 1/2 r,5r, 5 3/4 r,6r,7 1/4 r,8r,10r,12r,14r
small head adapter included
chamfer cutting att. included
1" thick Mtl capacit
tooling each worth 4-6k each |
|
Ad # 11010 | Crimping, Beading & Flanging Machines |
|
Engineering & Research& R |
HD |
Good |
Sold |
Photo /
More Info. |
metal former: former
vari speed drive upgraded |
|
We found 2 matching ads. Now displaying the remaining 2 ads.
Year |
Make |
Model |
Condition |
Price |
Details |
|
Ad # 10586 | Swagers |
1992 |
Conrac |
369 |
Good |
sold |
Photo /
More Info. |
: some dies included
specs to follow |
|
Ad # 10585 | Swagers |
|
PHI |
369 |
Good |
sold |
Photo /
More Info. |
: Swager
some tooling/dies
Tech specs to follow |
|
We found 16 matching ads. Now displaying the remaining 16 ads.
Year |
Make |
Model |
Condition |
Price |
Details |
|
Ad # 10945 | Welding Positioners |
|
Worthington |
Worthington-30 |
Fair |
sold sold |
Photo /
More Info. |
48" table : will hold 3000lb part
48" table
power tilt
needs some work |
|
Ad # 10943 | Misc. Welding Equip. / Acc |
|
Ransome |
12x12manipulator |
Very Good |
sold |
Photo /
More Info. |
12 FT. x 12ft Manipulator: 12 ft x 12 ft
all tooling we have with it
The basic machine is in good condition. I have 24 new Cam-Rol bearings that I was going to install but decided we did not need the unit as it is really too small for what we currently manufacture. The machine will need a forward/reverse contactor for boom up/down. It will also need a 1/2 HP DC drive motor and electronic controller plus a right angle gearbox and pinion for the boom in/out operation. I would need to spend about $1000.00 to purchase and install all of the parts it needs to be 100% usable. The new Cam-Rol bearings are worth $1000.00 alone. The 12' x 12' means it will weld a tank or whatever on a set of turn rolls that could be as much as 12' in diameter plus |
|
Ad # 10947 | Welding Positioners |
|
Aronson |
HD250CS |
Needs Work |
sold |
Photo /
More Info. |
48"x48" 3000# cap.: needs electrics |
|
Ad # 10948 | Welding Positioners |
70's |
|
6ft |
Good |
sold |
Photo /
More Info. |
6ft.x6ft table, 10,000 lb plus capacity: 6ft dia table
10,000lb plus capacity
90 deg tilt
machine is in good working condition
There is no name on it ,although there could have been. I have no manual for it. I upgraded the DC drive to current technology and the DC motor is relatively new.
|
|
Ad # 10951 | Welding Positioners |
|
P&H |
WP6 |
Very Good |
sold |
Photo /
More Info. |
6ft.x6ft. 6000# cap./9000# other way: very good shape
6ft.x6ft.
6000# cap./9000# other way |
|
Ad # 10946 | Welding Positioners |
|
Ransome |
10-P |
Very Good |
sold |
Photo /
More Info. |
30"x30" table: power tilt tables
30 " table
1000lb capacity
2 machines AVAILABLE |
|
Ad # 4324 | Spot Welders |
|
Acme |
PT2-4-8125 |
Good |
sold |
Photo /
More Info. |
42" THROAT ACME SPOT WELDER: 45" Throat
125 KVA Power supply with controls for weld
time,
power, dwell etc
Water Cooled Head
style : Soar |
|
Ad # 10937 | Spot Welders |
|
Tatylor Hatfield |
ERB-30-150 |
Good |
sold |
Photo /
More Info. |
150 KVA W/ 36" throat: 150 KVA
36" max throat depth
TJ Snow control
water cooled
Unitrol Solutions Controller |
|
Ad # 10744 | Misc. Welding Equip. / Acc |
|
Acorn & others |
various |
Good |
Sold |
Photo /
More Info. |
Acorn style welding platens/tables-all sizes: Some tables are Acorn brand others are not
4' x 4' ---3 pcs---1295.00ea
5 x 5' ---25pc-1495.00 ea
6' x 5'---20pc-1750.00ea
We can remove legs and load on truck.
Some with perimeter frames, some with angle legs and some with no legs.
Some acorn style tables have a 1-3/4", 1-5/8" or 1-1/2" square hole in them.... |
|
Ad # 11246 | Welding Positioners |
|
Pandjiris |
2-5MVRHT |
Good |
sold |
Photo /
More Info. |
18" Dia: Panjiris 18" positioner
manual tilt dial
4ft plate mounted on top
works well
The table tilts, runs forward and reverse
and
the
speed control works. It would cleanup nice.
The
speed reducer is mechanical and off-the-shelf
WW
Grainger. It could be converted very easily
to
DC
or variable frequency AC.
|
|
Ad # 11247 | Welding Positioners |
|
Panjiris |
2-5MVRHT |
Good |
sold |
Photo /
More Info. |
18" dia: 18" Dia base table
20" dia top plate
manual tilt
gear box has broken cover plate
250 lb capacity |
|
Ad # 11250 | Butt & Seam Welders |
|
custom |
|
Good |
sold |
Photo /
More Info. |
seemer fixture- clamping system: seemer fixture- clamping system
1/4" capacity
70" sheet length
pneumatic hold down
There is no welder power supply or mig or
tig
head. buyer would have to supply that.
There is no welder, tig or mig head for it.
We
ran a ‘Bugo’ head with track.
2. It will clamp any thickness from 0.0 to
~.0.250. Air pressure can regulated the
clamping
force.
3. What it will weld (thickness, carbon
steel,
stainless, aluminum etc) is a function of the
welding power supply and head chosen.
We built this unit many years ago to build
16
ga
stainless tanks. We also used it to ‘butt
weld’
sheets of stainless together. We have used
mig,
tig and cold wire tig with it.
It is just a ‘homebuilt’ unit. We used it
last
year when we manually ‘tigged’ some stainless
sheet together.
|
|
Ad # 11248 | Misc. Welding Equip. / Acc |
|
|
|
Fair |
sold |
Photo /
More Info. |
many sizes--tank rollers: tank rollers
many sizes
see pix
|
|
Ad # 11109 | Misc. Welding Equip. / Acc |
|
Phoenix |
700-BT |
Very Good |
sold |
Photo /
More Info. |
Powered flux oven / rod oven: This rod oven could easily be used for a powered flux oven as it will hold ... |
|
Ad # 11083 | Misc. Welding Equip. / Acc |
|
Dry-Rod |
|
Good |
sold |
Photo /
More Info. |
welding rod ovens: 19-units total units available -
17-Dry Rod brand ovens-450.00each2 unknown brand
Note: all but 2 are dry rod brand name units
These rod ovens are typical of what most shops would need
1 phase most are 120 volts but some are 120/240 850 watts on some 1000 watts
on others
Capacity 350 lbs of rods
Temperature range 100-550 degrees F
Quantity of 2 unknown brand at this time but very similar to Phoenix type 300:
These rod ovens are typical of what most shops would need
Voltage and wattage unknown but should be 120 or 120/240
Capacity 350 lbs of rods
Temperature 100-550 degrees F is most likely
|
|
Ad # 11009 | Butt & Seam Welders |
1990 |
Pandjiris |
|
Very Good |
sold |
Photo /
More Info. |
seam welder 78": Pandjiris seamer
78" travel
water cooled
arc voltage control
used for cold water TIG now
miller cooler
300Amp water cooled system
includes walkway
X & Y manual slide option |
|
We found 2 matching ads. Now displaying the remaining 2 ads.
Year |
Make |
Model |
Condition |
Price |
Details |
|
Ad # 16174 | Manual Arbor Press |
|
Greenerd |
# 4 |
Good |
sold |
Photo /
More Info. |
: Greenerd # 4 floor type heavy duty arbor press
Famco # 2 arbor press bench top
Dake # 1-1/2 B arbor press bench top,ratchet
type |
|
Ad # 10589 | Hydraulic 4 Post Press |
|
Custom |
350 Ton |
Good |
Sold |
Photo /
More Info. |
350 ton: 200 ton
182" between opening
was used to make tank domes-dishes
new controls |
|
We found 1 matching ad. Now displaying the final ad.
Year |
Make |
Model |
Condition |
Price |
Details |
|
Ad # 11011 | Heat Treat Related Equipment-Misc. |
|
Johnson gas Apparatus |
615KA |
Good |
sold |
Photo /
More Info. |
lead smelter: lead smelter
natural gas
156 BTU/hr |
|
We found 1 matching ad. Now displaying the final ad.
Year |
Make |
Model |
Condition |
Price |
Details |
|
Ad # 16161 | Cranes/Hoists & Manipulators |
? |
P & H |
|
Good |
sold |
Photo /
More Info. |
1 ton x 10ft : Jib Crane P & H
1/2" ton capacity hoist approx 12 ft tall
4 units available
remote pendant
3 units with 10 ft arm, one with 25ft arm
110/1 voltage
Note:recently have been disasemmbled for easy
loading |
|
We found 4 matching ads. Now displaying the remaining 4 ads.
Year |
Make |
Model |
Condition |
Price |
Details |
|
Ad # 10712 | Painting / Coating Equipment |
1993 |
JBI |
EA-24SB |
Excellent |
sold |
Photo /
More Info. |
16' x 24': 16 ft x 24 ft
top mount blower exhaust system
lighted
sprinkler system
buyer must dissasemble-we can load onto truck |
|
Ad # 10663 | Bead & Shot Blasters |
90,s |
Empire |
PF3648 w/ DCM 80A |
Good |
sold |
Photo /
More Info. |
44x26x29: Empire PF3648 with a DCM 80A dust collector unit all operating on 115 VAC.
dust collector system included
turntable inside
dimensions:44x26x29
Specifications that for a new PF3648SC that is very similar to ours.
Overall Dimensions::: Height: 72" Width: 38" Depth: 54"
Working Dimensions: Height: 36" Width: 36" Depth: 48"
L/R Side Door: 32" x 29"
Window: 22" x 14" Safety Glass With Quick-Change Frame
Construction: 14 Gauge Steel
Gun Assembly: Foot Operated: 14 CFM @ 90-100 PSI
Electrical: 110 Volt
Dust Collector: DCM-80A Dust Collector with pneumatic shaker and fabric tube filters (1 HP; 110 Volt)
Rubber Cloth-Lined Gloves
Two 120-Watt Flood Lights
Dust-Off Gun
Pneumatic Foot-Treadle Control
Air Pressure Regulator & Gauge
General Purpose Air Filter
Media Regulator
Leveling Bolts
3/16" Perforated Floor With 1000 Pound Capacity
Ventilation Rate: 400 CFM
The unit has the optional rubber hanging curtains on the doors and back of the cabinet to protect the metal surfaces from erosion. It also has the internal rotating table (1000Lb. capacity).
The DCM 80A filtration unit has tube filters with a pneumatic shaker and dump tray in the bottom. Much more expensive and higher quality than a vacuum only system.
|
|
Ad # 10664 | Bead & Shot Blasters |
90,s |
Profinish |
Model-PF3640 |
Good |
sold |
Photo /
More Info. |
36x48x32high: bag/filter reclaim system with machine |
|
Ad # 11249 | Bead & Shot Blasters |
|
blast it all |
|
Good |
sold |
Photo /
More Info. |
: specs to come
interior cabinet size:
abrasive seperator
light |
|
View Detailed Ads
Content copyright © 2011 NetMachinery.com. All rights reserved.
Please send your questions, comments, or bug reports to the Webmaster.
Website Hosting & Development by IndSite.
|
|