Year |
Make |
Model |
Condition |
Price |
Details |
|
Ad # 5577 | Multi Spindle Drill Press |
70's |
Moline |
HS29-36NC |
Good |
sold |
Photo /
More Info. |
Automatic cylinder drill unit : AB software & control-updated
40 spindles x 30"length-2MT
50" swing x 60" center distance
lots of tooling included, fixtures, chip conveyor
coolant
|
|
Ad # 1572 | Multi Spindle Drill Press |
|
United States |
10 Spindle Drill Head |
Good |
Sold |
No Photo /
More Info. |
10 Spindle Drill Head: Range" 1/2" to 3/4" diameter drills
10 Spindles |
|
Ad # 4237 | Multi Spindle Drill Press |
|
|
|
Very Good |
Sold |
Photo /
More Info. |
heavy duty 12 spindle: 12 spindle
coolant
controls
20" x 20" table
10HP motor
holders included |
|
Ad # 2203 | Multi Spindle Drill Press |
80's |
Walker-Turner |
|
|
Sold |
Photo /
More Info. |
3 head drill center: 1 HP motors
8" throat depth
1/2" drill capacity
adj. stroke height to 20"
42" table bed |
|
Ad # 1462 | Multi Spindle Drill Press |
1958 |
NATCO |
H6 |
Fair |
Sold |
Photo /
More Info. |
NATCO 16 Station Multi-Spindle Drill: 16 drill drive positions
Table approx 30" x 24" |
|
Ad # 1461 | Multi Spindle Drill Press |
|
South Bend |
HRG |
Fair |
sold |
Photo /
More Info. |
South Bend Multi-Spindle Drill: 24 Drill Drives
Table 24" x 15"
24" Work height
|
|
Ad # 1460 | Multi Spindle Drill Press |
1969 |
Cleereman |
ADT |
Fair |
sold |
Photo /
More Info. |
Dual Head, Multi-Spindle Drill: Table: 40" x 24"
10 drill Drives per side |
|
Ad # 1463 | Multi Spindle Drill Press |
|
NATCO |
H-6 |
Fair |
Sold |
Photo /
More Info. |
NATCO 24 Station Multi-Spindle Drill: 24 Drill Positions
Table: approx 30" x 24" |
|
Ad # 11660 | Multi Spindle Drill Press |
50s |
NATCO |
B16 |
Very Good |
sold |
Photo /
More Info. |
30 Hole: Natco B16
30 Hole Head
42" Diameter Table
Throat 10"min-28" max
|
|
Ad # 11659 | Multi Spindle Drill Press |
50s |
Natco |
b14 |
Very Good |
sold |
Photo /
More Info. |
24 Head : Natco B14
24 Spindle head
24" x 32" Table Air Powered
Throat 10" min -24" Max
|
|
Ad # 15601 | Multi Spindle Drill Press |
1967? |
Powermatic |
1200 |
Good |
sold |
Photo /
More Info. |
7/8" capacity: 4 head powermatic drill press
1.5HP each
speed: 200-2000rpm
20" throat depth
step pulley head for speed changett
7/8 steel capacity
Electric Motor - 208-230/480 VAC
|
|
Ad # 5269 | Multi Spindle Drill Press |
|
Powermatic |
1150 |
Fair |
sold |
Photo /
More Info. |
Powermatic 7-Head Drill Press: 7" Throats
Variable speed belt drives |
|
Ad # 5208 | Multi Spindle Drill Press |
1967 |
BURGMASTER |
1D |
Good |
sold |
Photo /
More Info. |
1/2"x 6-Spindle BURGMASTER #1D Turret Drill, S/N-1D-2741, Used : Specifications:
Number of Spindles 6
Spindle Speeds 4 per Spindle. 275 to 4010 RPM
Drilling/Tapping Capacity 1/2" in Cast Iron
Spindle Travel 6"
Head Travel 12"
Distance- Spindle to Table 20" Maximum
Distance- Spindle to Column 8-1/2"
Table Size 12"x 17" with Coolant Trough
Motor 2-Speed
Accessories Included (5) Drill Chucks, Tapping Head
|
|
Ad # 3181 | Multi Spindle Drill Press |
1971 |
Edlund |
1-1/2 F12 |
Good |
sold |
Photo /
More Info. |
Edlund 4 Head Drill: 750-6000 rpm
2 HP
12" Throat
Manual Downfeed
Coolant System
50" x 20" Table (adjustable)
24" under spindle |
|
Ad # 5181 | Multi Spindle Drill Press |
1952 |
Allen |
6 Spindle |
Good |
Sold |
Photo /
More Info. |
Allen 6 Spindle Drill Press With 12" Throat: 6 Spindles
Throat: 12"
Work Height: 22"
Table Size: 20" x 7"
Motor Size: 5 hp per
Coolant System |
|
Ad # 6558 | Multi Spindle Drill Press |
|
AVEY |
14 x 48 4-Head |
Good |
Sold |
Photo /
More Info. |
14" x 48" 4-Head AVEY Drill Press: Table: 14" x 48"
Table" Adjustable Height
Throat: 9"
Includes:
Multiple drill Head (6)
2 x Size 2, Type B, 750 rpm - one is a tapping head
Coolant System with pumps etc
NOTE: Drill fixtures are NOT included |
|
Ad # 6556 | Multi Spindle Drill Press |
|
AVEY |
4-Head |
Good |
Sold |
Photo /
More Info. |
13" x 44", 4-Head AVEY Drill Press: Table:13" x 44" (plus
Table: Adjustable Height
Throat: 9"
One Head: Size 2, Type R - 750 rpm (Tapping?)
2 x Plain Drilling Head, 1,240 - 4,800 rpm
Coolant System with pumps
NOTE: Drill ixtures NOT included |
|
Ad # 6555 | Multi Spindle Drill Press |
|
Kingsbury |
4-Head |
Good |
Sold |
Photo /
More Info. |
17" x 72", 4-Head Kingsbury Drill Press: Table: 17" x 72"
Table: Adjustable Height
Includes ONE multi-drill head (5)
Throat: 8"
Coolant System with pumps etc
NOTE: Drill fixtures NOT included |
|
Ad # 6554 | Multi Spindle Drill Press |
|
AVEY |
# 2, BMA-6 |
Good |
Sold |
Photo /
More Info. |
22" x 84", 5-Head AVEY Drill Press with 2 Tapping Heads: Table: 22" x 84"
Table: Adjustable Height
Throat: 42"
Spindle Speeds: 250, 1,000, 1,500 rpm in 3-Stages
Coolant System with pump
Includes 2 Tapping Heads
NOTE: Fixtures NOT included |
|
Ad # 6557 | Multi Spindle Drill Press |
|
AVAY |
4-Head |
Good |
Sold |
Photo /
More Info. |
14" x 72" AVEY 4-Headed Drill Press: Table:14" x 72"
Table: Adjustable Height
Throat: 7-1/2"
Coolant System with pump
NOTE: Drill fixtures NOT included |
|
Ad # 7795 | Multi Spindle Drill Press |
|
Burgmaster |
turret drill |
Very Good |
sold |
Photo /
More Info. |
6-Station BurgMaster Turret Drill Press : Burgmaster turret drill
Stations: 6
1/2" drill drill on it
Table Size: 23" x 39" (usable area)
Spindle Speed: 275 - 4015 rpm |
|
Ad # 12405 | Multi Spindle Drill Press |
|
Comander |
8-12 |
Good |
sold |
Photo /
More Info. |
8" throat 12 drill: Comander Multi Spindle Drill Press
12 Drills max
8" throat
4-adj drill positions:slots 5" long -adjustable
from: 12"+" max dia, min dia 2"-estimated
110 Volts
|
|
Ad # 9461 | Multi Spindle Drill Press |
2001 |
Controlled Automation |
BFC-530 |
Good |
sold |
Photo /
More Info. |
Used BeamLine for sale: 2001 Controlled Automation BFC-530 Beamline Punch (saw not included)
·Punching capacity: 1 1/16” dia. holes thru 1” mild steel
·In feed roller bed length: 65’
·In feed transfers width: 14’-6”
·Out feed roller bed length: 65’
·Out feed right side transfers width: 11’-6”
·Out feed left side transfers width: 21’-2”
·In feed and out feed roller bed widths 40”
|
|
Ad # 8489 | Multi Spindle Drill Press |
|
walker- turner |
|
Good |
Sold |
Photo /
More Info. |
7.5" throat , 1/2" chuck: 4 head manual feed drill units
7.5" throat
8" table to chuck
15" between spindles
1/2" chucks
1/2 HP |
|
Ad # 8480 | Multi Spindle Drill Press |
1971 |
Monarch/Edlund |
1-1/2F-12 |
Good |
sold |
No Photo /
More Info. |
Multi spindle drill press: 4 head unit
coolant
lift table
Variable speed heads 750-6000RPM |
|
Ad # 11225 | Multi Spindle Drill Press |
1950s |
Allen |
|
Fair |
sold |
Photo /
More Info. |
25" x 44" Table : 15Hp?
25" x 44" Table Size.
12" Throat.
adj crank table lift..
12" Spacing between Spindles. T Slot Bed. |
|
Ad # 11224 | Multi Spindle Drill Press |
1950s |
Allen |
|
Fair |
sold |
Photo /
More Info. |
Table Size 24" x 54": 10 Hp?
15" Throat.
24" Stroke. 25" Spacing between Spindles. T Slot
Bed. 24" x 54" |
|
Ad # 10294 | Multi Spindle Drill Press |
|
POWERMATIC |
1150 |
Good |
sold |
Photo /
More Info. |
4 HEAD DRILL PRESS: POWERMATIC 4 HEAD DRILL PRESS - 3 PHZ |
|
Ad # 7603 | Multi Spindle Drill Press |
|
Allen |
4 Spindle Drill |
Needs Work |
SOLD |
Photo /
More Info. |
Allen 4 Spindle Drill Unit: Has some problems with one of the spindles - otherwise in reasonable condit... |
|
Ad # 13275 | Multi Spindle Drill Press |
80's |
custom |
|
Good |
sold |
Photo /
More Info. |
multi spindle up to 36 holes at once: custom multi hole drilling unit
can drill up to 36 holes at once
2" drill spacing
68" overal bed length
uses a 6" 3 jaw chuck to hold part
coolant
chuck strokes in z axis approx 2" to do 72 holes in same plane
table has a 6" upstroke into drills
clamp system set up to do 1-2" dia pipe
this was used to drill holes in pipe at mutiple planes ..it indexes and rotates pipe
As far as I remember it is under power. I did say that the last time I turned it on it would not sequence through the drill/rotate cycle. There is a tenor drum timer (rotating drum with push pins that actuate switches) that is not indexing. I suspect the timer motor is defective. If I were going to use it, I would update it with a cheap (few hundred dollar) PLC.
We would ask $4,995 for it and unhook it, move it and load it for another $500.
There is a hydraulic motor, main drive motor and coolant motor. All of them are 575 3 phase.
Swapping them to 480 would require a motor change.
As far as I can tell, you can use any drill size that has a #1 Morse taper.
I found #1 Morse drills from 3/16 to 15/32.
The tool holders that we used go by the name of #1 Morse Taper Split Sleeve Drill and Reamer Drivers’. The split sleeve allows you to use up to a 3/8” straight shank.
I cannot see the motor data plate for HP, RPM, Frame etc. t looks like 15-20 HP.
There are 36 drilling positions spaced 2” apart. The chuck that holds the piece you are drilling not only rotates but goes in and out. This means the hole centers can be 1” or 2” apart longitudinally.
Sometimes we would skip drilling positions to increase the center distance between holes.
I will have to ask someone what the chuck degree stops are when rotating radially.
Remember, we built this gang drill for a very specific purpose.
|
|
Ad # 12022 | Multi Spindle Drill Press |
|
Allen |
|
Good |
sold |
Photo /
More Info. |
4 Spindle drill press: Allen 4 spindle drill press
5' x 2' table
150-1800 rpm
6" quills
#2 morse taper |
|
Ad # 2623 | Multi Spindle Drill Press |
80's |
|
|
Good |
Sold |
Photo /
More Info. |
Gang Drill Press-6 head : 6 Head Gang
Not a tapper |
|
Ad # 2584 | Multi Spindle Drill Press |
80's |
Allen |
27" |
Good |
Sold |
Photo /
More Info. |
Allen Gang Drill-3 head: 27"
3 Spindle
21" x 47" T-slot table
ac inverter on 1 spindle-variable speed
adj. table work height
3mt spindle
3Hp heads
auto downfeed
0-10" spindle height adj. |
|
Ad # 13168 | Multi Spindle Drill Press |
1990 |
Fanuc |
Drill Mate Model T |
Fair |
sold |
Photo /
More Info. |
10 Station atc: 19" x 14": Fanuc-Drill Taping Machine
Model Tape Drill Mate Model T
Yearˇ 1990
Country JAPAN
Controller Fanuc 0M
Tool Shank BT-30
Tool Number 10atc
X Axis Travel 19"
Y Axis 14"
Z-axis Travel 12"
Turn/rpm 6000rpm
|
|
Ad # 7251 | Multi Spindle Drill Press |
1965 |
DEKA |
HRG-1222-18 |
Very Good |
sold |
Photo /
More Info. |
16-Spindle Model HRG-1222-18 DEKA Multiple Spindle Hydraulic Drilling: 16-Spindle Model HRG-1222-18 DEKA Multiple Spindle Hydraulic Drilling and T... |
|
Ad # 7258 | Multi Spindle Drill Press |
1982 |
BURGMASTER |
2DCP |
Very Good |
Sold |
Photo /
More Info. |
BURGMASTER Six Spindle Turret Drilling and Tapping Machine, Model2DCP: BURGMASTER Six Spindle Turret Drilling and Tapping Machine, Model2DCP
Drilling capacity, mild steel 3/4"
Tapping capacity, mild steel 3/4" N.F.
Turret travel 8"
Table size 24" x 40"
Throat depth 11-1/2"
(12) Preselective spindle speeds, three ranges 225-3,000 R.P.M.
Carriage travel 15"
Work height, spindle nose to table, head up 9"
carriage down
Work height, spindle nose to table, head up 24"
carriage up
Feed, infinitely variable and preselective for each 1-45 I.P.M.
spindle
Rapid traverse, pre-selective in length for each 195 I.P.M.
spindle
Depth control, pre-selective in length for each plus or minus .002"
spindle
EQUIPPED WITH:
Electric feed system: Manual by fast or or slow Jog Control,
Semi-Automatic, orFully Automatic
Spindle Cycle Selector: allows complete automatic cycling. Each of the six spindles
can be programmed individually by the flick of the assigned thumbwheel. Rapid
approach points are adjustable through a cam setting. Automatic retraction at the
end of the machining operation (drilling, reaming, dwell for counterboring,
and boring). The turret then indexes bringing the tool into the new position. The
slide rapid traverses down to the new feed engagement point andthe new preselected machining operation occurs.
Spindle Function Selector is also programmed by thumbwheel. It provides the Cycle
Stop mode-that is, stopping the automatic cycle operation on a given spindle at the
conclusion of the spindle's preassigned cycle and also preselects the motor speed.
Key lock selector switch for Indexer Auto Enable
Rheastat for Reciprocating Feed (peck drill)
(6) 1/32"-1/2" Capacity ALBRECHT keyless drill chucks
External coolant pump and tank
2-1 H.P. 3/60/220-440 volt two-speed drive motor coupled to a two step belt drive
and electrical controls |
|
Ad # 13789 | Multi Spindle Drill Press |
|
Allen |
No. 2 1/2 Motor Spindle |
Fair |
sold |
Photo /
More Info. |
: Chas G. Allen
4 Spindle Drill Press
Table size: 25"x62" |
|
Ad # 11914 | Multi Spindle Drill Press |
1986 |
MSC |
|
Good |
SOLD |
Photo /
More Info. |
: In good working condition . Has all the various spindle attachments . Spind... |
|
Ad # 5664 | Multi Spindle Drill Press |
|
Allen |
2 Head |
Good |
Sold |
Photo /
More Info. |
2 -Headed multi spindle drill heads unit: 2 HP heads
800-2400RPM step pulley speed change
14" throat
24" spacing between main spindle heads
21 x 50" table
coolant
Auto down feed cycle & adj. feeds for tapping
Wiring prints included
up tp 9 drills can be adapted to each head type: Rockwell # 700 multi drill heads max spacing on head is 7" Dia.adjustable |
|
Ad # 7144 | Multi Spindle Drill Press |
|
South Bend/Deka |
HRG1222-28 |
Good |
Sold |
Photo /
More Info. |
4-Spindle South Bend/Deka Production Drill : Drill Stations: 4
Spindle Drive: 7.5 hp
Spindle Taper: # 0
Spindle Speeds: 260 - 2343 rpm
Table: 18" x 30"
|
|
Ad # 7143 | Multi Spindle Drill Press |
|
Allen |
4 Headed Drill Press |
Good |
Sold |
Photo /
More Info. |
Allen 4 Headed Drill Press With Power Feeds : 4-Heads
3 hp (each) |
|
Ad # 7145 | Multi Spindle Drill Press |
1991 |
BurgMaster |
1DLY |
Good |
SOLD |
Photo /
More Info. |
6-Station Turret Drill Press : Stations: 6
Table Size: 23" x 39" (usable area)
Spindle Speed: 275 - 4015 rpm
12" Throat
39" x 22" Table
6 Spindle Turret head.
|
|
Ad # 1674 | Multi Spindle Drill Press |
|
Leland-Gifford |
|
Fair |
SOLD |
Photo /
More Info. |
Variable Speed 3-Station Drill Press : Heavy duty |
|