Year |
Make |
Model |
Condition |
Price |
Details |
|
Ad # 10938 | Vertical Turret Lathe (VTL) |
1968 |
Gray |
Series 60 |
Good |
sold |
Photo /
More Info. |
84" table x 96" under rail: table-84"height under sadle-84"
height under ram face-
96"
plus
vert travel-48"
3" bore in ram head
max swing-96"
table top to floor-36"
overall mach. height-
14ft.
4 axis DRO system-both
rams up/down -left
/right
pit shown but not
required-due to
building
height restriction
Year 1967 or 1968 (not
quite sure)
This information below
was copied from
The G.A.
Gray Company Bulletin 92.
It seems accurate. There
is more room
under the rail than specified.
Machine size 84"
Table diameter 84"
Height under saddle 84"
Height under ram face
92"
Height under turret face
96"
Vertical travel (below
saddle) of ram
head
(std.) 48"
Vertical travel (below
saddle) of turret
head
(std) 30"
Vertical travel of side
head above table
80"
Horizontal travel of ram
head 54"
Horizontal travel of
turret head 57"
Horizontal travel of
side
head ram 32"
Travel past center - ram
head 1/2"
Travel past center -
turret head 1/2"
Travel of rail 74"
Swivel of ram head
either
side of
vertical 45
degrees
Size of bore in ram head
3"
Size of bore in turret
head 3"
Maximum swing, with or
without side head
96"
Feeds per revolution of
table (infinitely
variable) .002" - .250"
Table speed range rpm
(infinitely
variable) 0.8 - 194
Table top to floor 36
1/4"
Overall height machine
top to floor 14' -2"
Overall height pendant
top to floor 18'
Overall height top of
ram
to floor 18'
Two range simple
transmission
12,000 lbs table load
Automatic lubrication
Constant surface cutting
Power indexing turret
head
75 Hp DC table drive
All heads are DC drive
Rail head AC drive with
self leveling
feature
and automatic locking
There is a box full of
gears I suspect
are for
thread cutting and drum
scoring
1st I swapped the 5 HP
DC
drive control
for the
ram with the drive on the
on
the turret
head. I
chose to swap drives rather
than repair. 2nd
the
clutch slips on the turret
head when
raising/lowering the head.
We just put it
into the
fastest feed to get where
we
are going in a
hurry.
The machine has operated
like this for at
least 8
years and has never
bothered
us.
Everything else works as
it should i.e.
table,
rail, lube pump, way lube
feeders etc
I believe the machine was
made to be floor
mounted and we installed it in
a pit to lower
the overall height of the
machine for (1) hoist
rail bridge clearance and (2)
to keep the table
height lower. Currently our
hoist rail will not
clear the operator station
counterweighted
davit arm on top of the
machine
but it really
does not need to as we only
lift machining
parts not the Grays parts.
The pit depth is
20.5 and the table height to
the floor is
17.5. If floor mounted it
would put the table
at 38. Not a bad working
height. The 75 HP DC
motor is mounted on the
working
floor and is
belt driven to the table drive
sheave in the
pit. The DC motor is on a
separate frame so I
would think it may just be a
matter of some
shorter belts if both machine
and motor were on
top of the floor.
|
|
Ad # 15970 | Vertical Turret Lathe (VTL) |
|
Bullard |
56" Dynatrol |
Good |
sold |
Photo /
More Info. |
56" table dia: Bullard 56 dynatrol VTL
56" Bullard Dynatrol Vertical Turret
Lathe.
56'' table
66" swing
? under rail
6-jaw chuck
3 heads including a side head. |
|
Ad # 10743 | Vertical Turret Lathe (VTL) |
1940's |
CINCINNATI |
VBM 120 |
Good |
sold |
Photo /
More Info. |
126" max swing: CINCINNATI VBM-120" swing..Actual swing: 126"
ram travel 60"
table dia -84"
65" work height
RPM:0-40
50 HP
NO Pit required
table load over 25 Ton max
Under Power
2 heads
video possible
vintage 1940's no markings on it to give me a date
It now has a variable speed controller for both the main drive and the feeds. This eliminates the need for gearing and makes the speed and feed changes a lot easier
It also has an air clutch installed to eliminate the hard starting that the old system had
There has also been an upgrade to a modern lubrication system (Willie Vogel) which allows for ease of lubrication
no jaws with machine
cost to disasseble and load on truck: $ 10,000 |
|
Ad # 10740 | Vertical Turret Lathe (VTL) |
40's ? |
Betts |
|
Good |
Sold |
Photo /
More Info. |
78" dia chuck: 78" dia chuck
4 jaw chuck
20HP main motor
88" max swing between housings
60" side head travel
pit required
Buyer must pay rigging / loading |
|
Ad # 10739 | Vertical Turret Lathe (VTL) |
40's ?? |
Betts |
|
Good |
sold |
Photo /
More Info. |
9 ft chuck dia: 9 ft chuck Dia
14 ft max swing between housings
5ft max under rail
36" height under side head
hyd assist rail lift.
16 pc chuck jaws
60" arm travel -left to center, right to center
12" ram travel-up/down
ac vari speed drives
pit required
40 HP DC main motor
buyer must pay for rigging/loading..
electrical cabinet: 96" Wx 32" D x 64" H |
|
Ad # 10698 | Vertical Turret Lathe (VTL) |
|
Bullard |
Cutmaster |
Very Good |
Sold |
Photo /
More Info. |
42" : Turret and side head,
3 jaw chuck
5.5-200 RPM |
|
Ad # 11575 | Vertical Turret Lathe (VTL) |
? |
King Machine |
36" |
Very Good |
sold |
Photo /
More Info. |
40" VTL: King Machine
3 Jaw 36" Chuck Max turning Dia. 40"
4 Jaw Plate on Top of 3 Jaw Chuck
30" Max Hieght
0-25 degree cutter swing.
8-245 RPM
Feeds 0.010-0.5 Low Speed
0.003-0.125 HighSpeed
|
|
Ad # 7901 | Vertical Turret Lathe (VTL) |
60'S |
KING |
56 in |
Good |
sold |
Photo /
More Info. |
56" Table, 62" max swing --KING VTL: Max swing 62"
chuck Dia 56"
ram stroke-?
table is bearing type
turret head
Table Speed Range: 2.7 - 100 rpm in stages (gear driven)
Vertical Height Under Rail: 42"
Head Tiltable
no threading..
4 x Table/Chuck Clamps
Base Size: 7 Wide x 12 Deep x 12 High
Overall Size: 14 Wide x 13 Deep x 12 High
|
|
Ad # 8773 | Vertical Turret Lathe (VTL) |
|
bullard |
34 |
Good |
Sold |
Photo /
More Info. |
34" table dia: 34 CHUCK
24 UNDER THE RAIL
5 SIDE TURRETS
SIDE HEAD
24 HP MOTOR
TERMS AND CONDITIONS:
SPECIFICATIONS AND EQUIPMENT SUBJECT TO VERIFICATION WITH CORPORATE APPROVAL
FULL PAYMENT DUE PRIOR TO MACHINE PREPARATION FOR SHIPMENT
SUBJECT TO AVAILABILITY
|
|
Ad # 8772 | Vertical Turret Lathe (VTL) |
1952 |
Bullard Cutmaster |
30 |
Very Good |
Sold |
Photo /
More Info. |
30 in: CHUCK SIZE30
SWING WITH SIDEHEAD UP34
MAXIMUM SWING44
HEIGHT UNDER RAIL24
TURRET HEAD RAM TRAVEL26
TABLE SPEED6.2 RPM-225 RPM
FEEDS16: .026-.0005 IPR
MAIN MOTOR30 HP
RAM SWIVEL30 DEGREES
MACHINE WEIGHT APPROXIMATELY27,000 LBS
EQUIPPED WITH:
30 3-JAW MANUAL CHUCK
5 STATION TURRET HEAD
SIDE HEAD
TERMS AND CONDITIONS:
SPECIFICATIONS AND EQUIPMENT SUBJECT TO VERIFICATION WITH CORPORATE APPROVAL
FULL PAYMENT DUE PRIOR TO MACHINE PREPARATION FOR SHIPMENT
SUBJECT TO AVAILABILITY
|
|
Ad # 7863 | Vertical Turret Lathe (VTL) |
1968-69 |
Webster & Bennet |
48 in diam |
Good |
Sold |
Photo /
More Info. |
48" Webster & Bennet Vertical Turret Lathe with MIMIK Tracer Head: Hydraulic Tracer Unit (Mimik) |
|
Ad # 11506 | Vertical Turret Lathe (VTL) |
30s-40s |
Gisholt |
? |
Good |
sold |
Photo /
More Info. |
57" dia chuck x 42" 15 HP: Gisholt Machine 15 HP
57" Chuck
62" Max swing
24" Arm extension travel
40" ? height Under Arm
Has had 6000ibs Turned on table fine
Comes with tooling. |
|
Ad # 10590 | Vertical Turret Lathe (VTL) |
|
Bullard |
46" cutmaster/# 75 |
Needs Work |
sold |
Photo /
More Info. |
46" bullard cut master: 46" cut master-std specs please verify
Capacity: 46"
Motor: 40 HP 6.1-187 RPM
Under Rail: 48 in. Under Adjustable Rail
Features:
* 3 Jaw Chuck
* Adjustable Rail
* Side Head
* Square Turret
* Pendant Control
* Coolant
Table Diameter ........................ 46"
Maximum Swing W/Side Head ............. 52"
Maximum Swing Without Side Head ....... 59"
Max. Height Under Rail ................ 44"
Turret Stroke ......................... 30"
Table Speeds .......................... 6.8-250 RPM
Feeds ................................. .006-.125 IPR
Machine Weight ........................ 45,000 Lbs
EQUIPPED WITH:
4-Position Square Turret
Side Head
no threading capability
have some machine prints |
|
Ad # 6499 | Vertical Turret Lathe (VTL) |
|
KING |
M-36 |
Fair |
SOLD |
Photo /
More Info. |
36" King VTL With Side Head: 36" Diameter Table
5 Station Turret
Side Head |
|
Ad # 12473 | Vertical Turret Lathe (VTL) |
1960s |
Bullard |
42 |
Good |
sold |
Photo /
More Info. |
42": Bullard 42"
Voltage 220/440 wired 220
42" Chuck 48" Swing
5-168 RPM Chuck
32" Vertical Travel |
|
Ad # 6183 | Vertical Turret Lathe (VTL) |
|
SCHEISS |
040 |
Good |
Sold |
Photo /
More Info. |
40" VERTICAL TURRET LATHE: DIAMETER OF 4-JAW TABLE ............. 39-1/2"
SWING WITH SIDE HEAD IN PLACE ....... 42"
SWING WITHOUT SIDE HEAD ............. 50"
SPINDLE SPEEDS ...................... (16) 6.2 TO 310 RPM
MAXIMUM UNDER RAIL .................. 46"
HORIZONTAL TRAVEL OF TURRET HEAD .... 28"
VERTICAL TRAVEL OF TURRET HEAD ...... 27"
HORIZONTAL TRAVEL OF SIDE HEAD ...... 24"
VERTICAL TRAVEL OF SIDE HEAD ........ 28"
FEEDS............................... (12) .002 TO .259 IPR
EQUIPPED WITH:
5 POSITION TURRET HEAD ON RAIL
SIDE HEAD
PENDANT CONTROL
30 HORSEPOWER MAIN MOTOR |
|
Ad # 6181 | Vertical Turret Lathe (VTL) |
|
BULLARD |
CUTMASTER 036 |
Very Good |
SOLD |
Photo /
More Info. |
36" VERTICAL TURRET LATHE: 36" VERTICAL TURRET LATHE
DIAMETER OF 4 JAW TABLE ....... 36"
TABLE SPEEDS .................. (20) 4.93 - 180 RPM
FEEDS ......................... (16) .0026 TO .500 IPR
VERTICAL TURRET TRAVEL ........ 26"
FACE OF TURRET TO TABLE ....... 41-1/4" MAXIMUM
SWING, SIDE HEAD UP ........... 39"
SWING, SIDE HEAD DOWN ......... 45" DIAMETER
SWIVELING TURRET HEAD ......... YES
5-POSITION TURRET ON RAIL ..... YES
4-WAY TOOL POST ON SIDEHEAD ... YES
PENDANT CONTROL ............... YES
MOTOR ......................... 30 HORSEPOWER
|
|
Ad # 6184 | Vertical Turret Lathe (VTL) |
|
KING |
042 |
Good |
sold |
Photo /
More Info. |
42" VERTICAL TURRET LATHE: DIAMETER .............................. 42"
SWING ................................. 46"
TABLE SPEED ........................... 4.1 TO 125 RPM
TRAVEL OF THE RAM ....................26" VERTICAL
SADDLE TRAVEL ON RAIL ................37" RIGHT TO LEFT
HEIGHT UNDER RAIL ..................... 39" (RAM HIGHEST POSITION)
SIDE HEAD WITH 4 WAY TOOL POST ........ 1-1/4" SQUARE TOOL
HORIZONTAL TRAVEL ..................... 22"
VERTICAL TRAVEL ....................... 31"
FEED RATES FOR THE HEADS .............. 12
CHANGES ............................... 1/96" TO 1/2"
RAPID TRAVERSE ........................ YES TURRET RAIL HEAD AND SIDE HEAD ........ YES
4 JAW CHUCK ........................... YES MOTOR ................................. 20 HORSEPOWER
|
|
Ad # 6186 | Vertical Turret Lathe (VTL) |
|
BULLARD |
CUTMASTER 054 |
Good |
sold |
Photo /
More Info. |
54" VERTICAL TURRET LATHE: TABLE CHUCK DIAMETER (4-JAW) ....... 54"
MAXIMUM SWING W/O SIDE HEAD ........ 62"
TABLE SPEEDS ....................... (20) 3.3 TO 120 RPM
FEEDS .............................. (16) .0026 TO .500 IPR
THREADS (ENGLISH)................... (15) 2 TO 18 TPI
THREADS (METRIC) ................... (13) 1 TO 7 TPMM
MAXIMUM HEIGHT UNDER RAIL .......... 44"
VERTICAL CROSS RAIL TRAVEL ......... 32"
HORIZONTAL TURRET HEAD TRAVEL ...... 73-3/4"
VERTICAL TURRET HEAD SLIDE TRAVEL .. 30-3/8"
VERTICAL SIDE HEAD TRAVEL .......... 44-1/4"
HORIZONTAL SIDE HEAD SLIDE TRAVEL .. 27"
FLOOR TO TABLE ..................... 36"
1-SWIVEL TURRET RAIL HEAD W/TURCHAN HYDRAULIC TRACER (NEW 1968)
1-RIGHT HAND SIDE HEAD ............. YES
THREAD CUTTING ATTACHMENT .......... YES
TABLE DRIVE MOTOR, HORSEPOWER ...... 50
|
|
Ad # 13371 | Vertical Turret Lathe (VTL) |
|
Bullard |
36 |
Good |
sold |
Photo /
More Info. |
36": Bullard 36" VTL
30HP
3 Jaw 34" Chuck
36" Max swing
220/440 Wired 480
18" Cutter Travel
6 Tool Turret
|
|
Ad # 10381 | Vertical Turret Lathe (VTL) |
2010 |
YM |
C5225E |
Very Good |
sold |
Photo /
More Info. |
1: Main technical specification
NameunitC5225E
Max. turning diametermm2500
Table diametermm2250
Max. turning heightmm2000
Max. weight of workpieceT10
Max. cutting force of right tool postKn35
Max. cutting force of left tool postKn30
Max. torque of tableKn.m63
Stage number of variable speed16
Rotate range of tabler/min2-63
Feeding rangeMm0.25-90
Level stroke of tool postMm1400
Vertical stroke of tool postMm1000
Beam moving speed Mm/min350
Tool rest rapid traverse speedMm/min1560
Moving degree limit of vertical tool post‘ΐ30
Main motor powerKw55
Work platform guideway formPitot/static pressure
Weight(about)T35
|
|
Ad # 10380 | Vertical Turret Lathe (VTL) |
2010 |
YM |
CJ5240 |
Very Good |
sold |
Photo /
More Info. |
1: Main technical specification
Name Unit CJ5240
Max. turning diametermm4000
Table diametermm3600
Max. turning heightmm2500
Max.weight of workpieceT32
Max. cutting force of right tool postKn35
Max. cutting force of left tool postKn30
Total cutting forceKn65
Stage number of variable speedTwo gear+stepless/16
Max. torque of tableKn.m80
Rotate range of tabler/min0.5-50
Level stroke of vertical tool postMm2200
Vertical stroke of vertical tool postMm1300
Beam strokemm2250
Vertical tool post moving degree limitdegree30
Feeding stage number of tool post 18
Beam lifting speedMm/min350
Tool rest rapid traverse speedMm/min1560
Sectional dimension of cutter barmm40*50
Main motor powerKwDC75
Overall size(L*W*H)mm5800*5000*4600
Weight(about)T68
|
|
Ad # 13327 | Vertical Turret Lathe (VTL) |
1940s |
Bullard |
42 |
Needs Work |
sold |
Photo /
More Info. |
42" table dia: Bullard 42"
Chuck 42"
Max swing 46"
Voltage 220
Machine runs fine needs some work to keep machine in gear |
|
Ad # 12225 | Vertical Turret Lathe (VTL) |
1983 |
Monarch |
VTN 10 |
Fair |
sold |
Photo /
More Info. |
51" swing by 24" : Monarch VTN 10
48" Chuck
51" swing x 24"
GE Mark Century 1050 Control
Year 1983
6 Tool Holder Turret
Monarch VTN 10 CNC Lathe
General Electric Mark Century 1050 CNC
controller
5 position turret
53" Swing, 24.5" height
Spindle, 75 hp
loading/rigging fee $ 1600.00..must
remove
top ram ?? low boy --maybe ??
|
|
Ad # 14021 | Vertical Turret Lathe (VTL) |
50's |
Bullard |
|
Excellent |
sold |
Photo /
More Info. |
50" table: Table Diameter-50"
Swing Side Head Lowered-56"
Turret Face to Table48-1/2"
Clearance Under Cross Rail35-1/2"
Vert Turret Travel29-1/2"
Clearance Under Side Head Slide25"
Floor To Table34"
Turret Rail Treavel28"
Vert Side Head Travel29"
Horiz Side Head Travel 27"
Vert Rail Travel16"
Table Speeds (12)3.5 - 60rpm
Feeds (8) .011 - .500 ipr
Main Motor 25hp
|
|
Ad # 14613 | Vertical Turret Lathe (VTL) |
|
Bullard |
50" |
Fair |
sold |
Photo /
More Info. |
50" chuck: bullard Vertical turret lathe
chuck size: 50"
side arm acc
note: has not been run in a few years but
was working when last used. |
|
Ad # 12162 | Vertical Turret Lathe (VTL) |
|
Bullard |
42 |
Good |
sold |
Photo /
More Info. |
3 Jaw 42": Bullard 42"
6 Station Turret
42" Chuck 3 Jaw
Voltage 480
|
|
Ad # 8321 | Vertical Turret Lathe (VTL) |
1981 |
Toshiba |
TX-13 |
Excellent |
Sold |
Photo /
More Info. |
63in Swing TOSHIBA VTL: Nice unit, we have a Tx-16 as well, under power and ready with updated read... |
|
Ad # 5836 | Vertical Turret Lathe (VTL) |
1950's |
John Bertram |
|
Needs Work |
Sold |
Photo /
More Info. |
: 40" table, side cutting tool post, 5 position turret, ~1950 |
|
Ad # 10170 | Vertical Turret Lathe (VTL) |
|
Niles/Pond |
|
Good |
sold |
Photo /
More Info. |
16' Swing: 14' Table, 16' Swing,
16' under the rail, (2) ram heads, updated electrics.
tracer attach
pendent control |
|
Ad # 12010 | Vertical Turret Lathe (VTL) |
|
Schiess |
164 |
Good |
sold |
Photo /
More Info. |
48" width 42" hieght: Schiess 164
5 Turret Tool Holder
47" Chuck T slotted
Voltage 440/3 phase
4-125 RPM
48" x 48" aprrox working area |
|
Ad # 7296 | Vertical Turret Lathe (VTL) |
Nov 69? |
SIGMA |
DKZ 25000\ |
Very Good |
SOLD |
Photo /
More Info. |
88" Table, 100" Swing Sigma VTL: Table: 88" diameter
Swing: 100"
4-Jaw chuck arrangement
Table Drive: 36 kW (approx. 46 hp)
Table RPM: 1 - 50 rpm in 18 steps
Head Tilt
87" Under the Rail
Ram Travel: 64"
Drilling Depth from Cross Rail Arm: 63" (1,600 mm)
Feed Ranges:
0.0012" - 0.002" - 0.003"
0.005" - 0.008" - 0.012"
0.02" - 0.03" - 0.05"
0.6" - 0.12" - 0.2"
|
|
Ad # 13765 | Vertical Turret Lathe (VTL) |
|
King |
46 |
Needs Work |
sold |
Photo /
More Info. |
40 HP 46" Chuck: King Machine VTL
46" Chuck
6 Tool Turret
Cross slide
Prototrack DRO track 102
36" Arm Travel
43" inch Under Tool Turret
40HP
Wired 460 Volts
Machine works for the most part but has minor electrical issues.
|
|
Ad # 8147 | Vertical Turret Lathe (VTL) |
1975? |
Schiess |
EK-125 |
Good |
sold |
Photo /
More Info. |
48 inch VTL: 48" Dia table, swing 51"-54" max
height under rail: 32-36" max
side arm cutter
column up/down-reverse switches need minor repair
table feed
coolant
3 & 4 jaw chuck included
Type of machine Vertical Turret Lathe - Single Column
Make SCHIESS
Technical details
faceplate diameter 1300 mm
chuck diameter 1200 mm
turning height 1250 mm
spindle speeds 8 - 95 u / min
Additional information
Single Column Vertical Turret Lathe Machine with Side Head, Tool-Holders, 4 Table Jaws,
rigging/loading fee approx $2000.00
|
|
Ad # 7130 | Vertical Turret Lathe (VTL) |
?? |
King |
46" Table Machine |
Good |
sold |
Photo /
More Info. |
46" Diameter, KING VTL With Side Head and Taper Attachment : Table Diameter: 46"
Swing: 56"
Vertical Clearance Under Rail: 42"
Drive: 40 hp
Table Speed: Infinitely Variable from 0 - 240 rpm
Feeds: 0.002" to 0.25 i/rev
Turret: 5 Stations
Side Head
Taper Attachment
2-Axis DRO: Trak 102 in X and Y |
|
Ad # 9159 | Vertical Turret Lathe (VTL) |
1954 |
King |
M-36 |
Excellent |
sold |
Photo /
More Info. |
36" Chuck: King 36" VTL bought NEW from Gov't storage in 1995 has only 10 years servic... |
|
Ad # 13071 | Vertical Turret Lathe (VTL) |
|
bullard |
36 |
Good |
sold |
Photo /
More Info. |
36 inch table: Bullard with 36 inch table
good working condition.
taken out of production on 01-10-2013 machine was overkill for our application , gaurds come with it , make offer |
|
Ad # 15399 | Vertical Turret Lathe (VTL) |
1950's |
Bullard |
42" |
Good |
sold |
Photo /
More Info. |
42" 3 jaw chuck: Vertical Turret Lathe
Make: Bullard (Spiral Drive)
Model: 42"
Electrical: 220/3 phase
Table Size: 42"
Max Swing: 44"
Height Under Cross Rail: 33"
Height Under Turret Face: 43-1/2"
Table Speeds: (12) 4.1 to 70 RPM
Vertical Head Movement: 27"
Vertical Head Will Face: 44"
Vertical Movement Of Side Head: 25"
Horizontal Movement Of Side Head: 21"
30 HP Drive Motor
42" 3-Jaw Chuck
|
|