Year |
Make |
Model |
Condition |
Price |
Details |
|
Ad # 4325 | Ram Type & Saddle Type Turret Lathes |
67? |
Gisholt |
2-L/13W-9137 |
Good |
sold |
Photo /
More Info. |
Heavy Duty Turret Lathe: Swing: 24"
Distance Between centers: 60"
Spindle Bore: 4.25"
4 way toolpost
notes:below
air gap and a chuck at 22 and 24
diameters.
The
22 clears the ways and the 24 would hit
the
ways. It also shows the dimension from
center
of
the chuck to a level point across the
ways.
Dimensions:
The total distance outside the ways is
17
(his
was 15). The operator side way is 4 ½
across.
The opposite side way is 3 across. The
air
between the ways is 9 ½ (his was 7 ½).
The
ways
are 1 Ό thick.
The center of the chuck to level across
the
ways
is 11. The swing is debatable
22
definitely
clears the ways. A circle drawn at chuck
center
point could be a little less than 24
before
touching the ways considering the air
gap is
also on center.
Voltage:
575 3 phase
The drive motor, rapid
traverse
motor and coolant pump most likely can be
rewound
for 230/460. There is a small multi-tap
control
transformer inside the control cabinet. It
is
wired for 575 but has the connections for
230
and
460 as well.
Condition:
I dont know if it runs. The headstock
and
rapid
traverse oil site gauges show middle of
the
sight glass bulls eye.
Manual etc.
I have a manual and what looks to be a
complete
electrical print.
Other stuff:
It has a chuck switch and inch
switch.
This
is used on our other Gisholts to maneuver
the
chuck so as to insert the chuck wrench.
loading fee: $ 800.00
|
|
Ad # 9768 | Ram Type & Saddle Type Turret Lathes |
1982 |
Shibaura |
S-2040 |
Very Good |
sold |
Photo /
More Info. |
table 2000mm Max swing4000: Shibura single column ram type vertical lathe
YOP 1982
Table 2000
Max swing 4000
Height 1600
DRO 2axes
Under power
|
|
Ad # 11685 | Ram Type & Saddle Type Turret Lathes |
|
Jones & Lambson |
# 4 |
Fair |
sold |
Photo /
More Info. |
# 4Turret Lathe: J & L #4 turret lathe
12" 3 jaw chuck
2-1/2" spindle bore
|
|
Ad # 4024 | Ram Type & Saddle Type Turret Lathes |
|
Warner & Swasey |
Model 1A |
Needs Work |
sold |
Photo /
More Info. |
Warner & Swasey Turret Lathe: Swing: 18"
Spindle Bore: 3"
Turret: 6-Station
Comes with some Collets |
|
Ad # 4022 | Ram Type & Saddle Type Turret Lathes |
|
Libby |
|
Fair |
Sold |
Photo /
More Info. |
Libby Turret Lathe: Swing: 24"
Turret: 6 -Stations
Spindle Bore: 3 1/2" |
|
Ad # 4013 | Ram Type & Saddle Type Turret Lathes |
1941 |
Morey |
Model 2-G |
Fair |
SOLD |
Photo /
More Info. |
Second Operation Turret Lathe: Swing: 15"
Bed Length: 30"
6-Station Ram-Type Turret
Spindle: 1" Through Bore |
|
Ad # 3990 | Ram Type & Saddle Type Turret Lathes |
?66 |
Warner & Swasey |
# 3 |
Fair |
Sold |
Photo /
More Info. |
Heavy Duty W&S # 3 TURRET LATHE: Swing: Approx: 15"
Bed Length: 36"
Cross Slide
Spindle Bore: 1.5"
6-Station Turret |
|
Ad # 15351 | Ram Type & Saddle Type Turret Lathes |
? |
Warner & Swasey |
# 3 /M1200 |
Good |
sold |
Photo /
More Info. |
12" chuck: Warner & swasey # 3 turret lathe
std mfg specs below-please verify actual machines
Hardened and ground bedways - Maximum swing over bedways: 15-3/8 - Spindle bore: 1-27/32 - 12 spindle speeds: 67 to 1480 RPM - Standard feeds on both aprons - A1-6 American standard spindle taper - Includes 10 3 jaw manual chuck - Includes hex turret - Chip pan and miscellaneous guards - Approx. weight: 3,250 LBS Elect.
Specs: - HP: 5/2.5 - Volts: 220 - Phase: 3 - Cycle: 60
Type A Spindle Nose, 6" size. There are both outer and inner bolt circles, (23) 1/2-13 tapped holes in M-1200
Note: nice machine,qc tool post not included |
|
Ad # 1311 | Ram Type & Saddle Type Turret Lathes |
? |
Hitachi Seiki |
5AII |
Fair |
Sold |
Photo /
More Info. |
Hitachi Seiki Turret Lathe (Made in Japan): Max Swing 20"
Swing Over Slide 14"
Z 24"
Spindle Bore 3"
6 Station tuttet (plumbed for coolant)
|
|
Ad # 10717 | Ram Type & Saddle Type Turret Lathes |
|
Hardinge |
DSM-59 |
Good |
sold |
Photo /
More Info. |
: collet closer
4.5" swing over slide
die head
parting tool
6 station turret
variable speed spindle-230-3500RPM
some tooling
1 hp |
|
Ad # 12630 | Ram Type & Saddle Type Turret Lathes |
|
Warner & Swasey |
No 4 |
Good |
Sold |
Photo /
More Info. |
Threading!!!: Warner & Swasey # 4
turret lathe
No 4
6 Tool Turret
8" chuck 3 jaws
!!!!Threading!!!!
Air Power Chuck |
|
Ad # 12627 | Ram Type & Saddle Type Turret Lathes |
|
Sundstrand |
Model 8 |
Good |
sold |
Photo /
More Info. |
10" x 25": Sundstrand Model 8
Fully Automatic
9HP
Hydrailic Tail Stock
Air chuck
Cam Drive
|
|
Ad # 12623 | Ram Type & Saddle Type Turret Lathes |
1980 |
Herbert |
No 2 |
Good |
sold |
Photo /
More Info. |
10" x 25": Herbert No 2 Turret Lathe
50-2000 Rpm
6 Tool Turret
3 Jaw 8" Chuck
11" Of turret travel
2" Spindle Bore with Bar feed
2D Collets
Power Feed On Z
|
|
Ad # 5218 | Ram Type & Saddle Type Turret Lathes |
1970 |
WARNER & SWASEY |
M4670 |
Very Good |
Sold |
Photo /
More Info. |
#5-4 1/2 WARNER & SWASEY M4670 Ram Type Turret Lathe, : Specifications:
Swing over Bed 20"
Swing over Cross-Slide 10-1/4"
Spindle Bore 4-5/8"
Spindle Mount A1-11
Spindle Speeds (Preselect Head) (24) 25 to 1000 RPM
Carriage Feeds (6) .005 to .047 IPR
Cross Feeds (6) .002 to .018 IPR
Turret Feeds (6) .004 to .045 IPR
Motor 20/10HP 440V 3Ph 60C
Weight (Approximate) 10,000 Lbs.
Floor Space (excluding barfeed) 129" x 75" x 60"Ht.
Equipped with Collet Setup, Collet Pads, Hydraulic Barfeed; Square Turret Tool Post, Rear Cutoff Toolpost; Taper Attachment, Leadscrew Threading Attachment and Hydraulic Rapid Traverse on Cross Slide Carriage; Coolant; 2 each Short and Long Flange Tool Holders
|
|
Ad # 6509 | Ram Type & Saddle Type Turret Lathes |
|
Jones & Lamson |
# 5 |
Good |
SOLD |
Photo /
More Info. |
10" x 40" Universal Turret Lathe, Model # 5: Swing: 10"
Bed Length: 40"
Includes:
Collet Chuck and set of collets
Bar Feeder |
|
Ad # 14202 | Ram Type & Saddle Type Turret Lathes |
|
Jones & Lamson |
No 3 |
Good |
Sold |
Photo /
More Info. |
2" Spindle Bore : Jones and Lamson No 3
Turret Lathe
note: below are
std mfg
specs..please
verify actual
machines
10"
Chuck
30-
1500 RPM
10
HP
6
station Turret
Spindle Bore 2"
Swing over bed Ways
21"-1/4"
Swing over Carriage
/saddle 9.5 and 11"
over cross slife
Total Carriage
Travel
29" 3/4"
12 SPINDLE
SPEEDS
30-1500 RPM
24 THREADS
CHANGING SCREWS
4 -32 TPI
9 FEEDS ON
CARRIAGE AND TURRET
.005-.100 IPM
little
tooling: 4 jaw
chuck,toolpost,
|
|
Ad # 6395 | Ram Type & Saddle Type Turret Lathes |
1967 |
Herbert |
# 2-D |
Good |
sold |
Photo /
More Info. |
Herbert # 2-D Peg Board Automatic Turret Lathe: Large selection of tooling including collets.
Static Bar Feeder
Parts Catcher
All manuals |
|
Ad # 9506 | Ram Type & Saddle Type Turret Lathes |
|
WARNER & SWAYSEY |
2A |
Good |
SOLD |
Photo /
More Info. |
18" CHUCK: 4" Spindle Hole
Spindle RPM Range 16 to 1117rpm
Square Turret on Cross Slide
18" 4 Jaw Scroll Chuck? (as pictured).
All Tool Holders (as pictured)20/40 hp main motor 220/3/60
|
|
Ad # 8524 | Ram Type & Saddle Type Turret Lathes |
|
Jones & lamson/J& L |
# 5 |
Very Good |
sold |
Photo /
More Info. |
# 5 ---12in swing x 24 centers: 12" swing, 24" centers
2-1/2" spindle bore
12" 3 jaw chuck
ram type
misc tooling included
rigging fee to load onto your truck: $600.00 |
|
Ad # 8525 | Ram Type & Saddle Type Turret Lathes |
|
Warner Swasey |
# 2A |
Fair |
sold |
Photo /
More Info. |
: saddle type
15" 3 jaw chuck
3-3/4" spindle bore |
|
Ad # 10411 | Ram Type & Saddle Type Turret Lathes |
|
feeler |
fsm-59 |
Good |
sold |
Photo /
More Info. |
hardinge style turret lathe: |
|
Ad # 2919 | Ram Type & Saddle Type Turret Lathes |
1950's |
J & L |
# 7A |
Good |
Sold |
Photo /
More Info. |
J & L "Saddle Type" Turret Lathe: 20-1000 rpm
12" swing over cross slide
18" swing over ways
16" - 3 jaw chuck
60" distance between centers
Hydraulic chuck actuator and unit |
|
Ad # 2917 | Ram Type & Saddle Type Turret Lathes |
1950's |
J & L |
#5 |
Good |
sold |
Photo /
More Info. |
J & L Ram Type Turret Lathe: 3" spindle bore
20" swing over ways
12" over cross slide
12"-3 jaw chuck
36" distance between centers
4 way tool post
Miscellaneous tooling and holders |
|
Ad # 8434 | Ram Type & Saddle Type Turret Lathes |
|
Warner & Swasey |
# 2, 1330 |
Very Good |
Sold |
Photo /
More Info. |
Warner & Swasey # 2 Turret Lathe: Spindle Speeds 67 to 740. RPM
Swing Over Bed 14" |
|
Ad # 5957 | Ram Type & Saddle Type Turret Lathes |
1971 |
GISHOLT |
No.5-3 |
Very Good |
sold |
Photo /
More Info. |
No.5-3 GISHOLT Masterline Ram type turret lathe with SCR drive: No.5-3 GISHOLT Masterline Ram type turret lathe with SCR drive
Swing over bed ways 21 Ύ
Swing over carriage wings 18 Ύ
Swing over cross slide 12 1/8
Bar capacity 3
Bed width 12
Spindle nose A1-8
Cross slide travel 11 Ύ
Longitudinal travel of cross slide 25 Ύ
(8)Power longitudinal & cross feeds .003-.031 IPR
Hexagon turret turning length 15.62
Max. distance spindle to turret face 37
8 power longitudinal feeds of turret .003-.031 IPR
24 Spindle speeds 30-1500 RPM
EQUIPPED WITH:
Hardened bed ways
Curvic couplings on both hexagon & square turrets
Leader type threading with (5) leaders
Square front turret tool post
Hexagon turret
Mimik hydraulic tracer attachment mounted on rear slide
Pneumatic collet chuck with approx. (50) sets of collets
8 Ό dia. 3-jaw universal chuck
Swing type pendant control
Power assisted turret indexing
Dual feeds on cross slide
(5)short flange type tool holders
(1)long flange type tool holders
(1)live center
(1) drill chuck
Pan bed and coolant
Variable speed drive with up-dated Square D-Altvar
S.S. controls, pendant control mount
3/60/440 volt control voltage
|
|
Ad # 5956 | Ram Type & Saddle Type Turret Lathes |
1957 |
BARDONS & OLIVER |
No.4 |
Good |
sold |
Photo /
More Info. |
No. 4 BARDONS & OLIVER Ram type turret Lathe: No. 4 BARDONS & OLIVER Ram type turret Lathe
Bar capacity 4
Hole thru spindle 4 Ό
Max. swing over bed 18 1/8
Max. swing over carriage guides 16 ½
Max. swing over cross slide 9 ½
Max. distance end of spindle to face of turret 32 ½
Width across bed ways 9
Hexagon turret travel 12
Cross slide cross travel 9 ½
Cross slide carriage longitudinal travel 26
16 Spindle speeds 31-1550 RPM
12 longitudinal feeds .0025-.050 IPR
12 hexagon turret feeds .0025-.050 IPR
12 cross feeds .0015-.030 IPR
EQUIPPED WITH:
Preselector headstock
Hardened bed ways
Hexagon turret
Front square tool holder
Rear tool holders
Large quantity of collet pads, turret tooling, boring bars
Power operated collet chuck
12 Dia. 4-jaw chuck
Pan bed and coolant
10 H.P. 3/60/220-440 Volt Motor w/ controls
3/60/440 Volt operation
|
|
Ad # 5958 | Ram Type & Saddle Type Turret Lathes |
1957 |
WARNER & SWASEY |
M-3500 |
Good |
SOLD |
Photo /
More Info. |
#3A WARNER & SWASEY Square Head Saddle Type Turret Lathe, Model M-3500: #3A WARNER & SWASEY Square Head Saddle Type Turret Lathe, Model M-3500
Maximum swing over carriage guard: 23-1/2"
Maximum swing over bed: 24-1/2"
Maximum swing over carriage horn: 18"
Bar capacity - Round: 4-1/2"
Square: 3-3/16"
Hexagon: 3-7/8"
Spindle nose: A-11"
Cross slide specs: Cross travel - 14-3/8"
16-Cross feeds - .0025 to .082 IPR
Longitudinal travel - 51"
16-Longitudinal feeds - .005 to .167 IPR
Hexagon turret specs: Longitudinal travel - 51"
16-Longitudinal feeds - .005 to .167 IPR
Diameter of holes - 5"
Maximum distance, spindle to turret face - 59"
Length turned: 43"
16-Spindle speeds: 12 to 426 RPM
EQUIPPED WITH:
Square, pre-selector headstock
Hardened ways
Square toolpost
Rapid traverse to side carriage
Telescopic way covers
Overhead pilot bar
21" Dia. 3-jaw universal chuck
Chuck guard
(2) 2-Hole vertical slide tools
(1) Multiple boring head with pilot hole
(2) Long flange type toolholders
(1) Short flange type toolholder
(3) Boring tools
Pan bed with splash guard
30 H.P. 3/60/220-440 volt motor with controls
Machine wired for 3/60/440 volt operation
|
|
Ad # 7626 | Ram Type & Saddle Type Turret Lathes |
|
Morey |
2-G |
Very Good |
sold |
Photo /
More Info. |
Morey 2-G: Turret Lathe With Collet Chuck: Morey 2G turret lathe
Collet Chuck with some collets included
14" swing over bed, 6" over cross slide. 3hp variable speed Reeves drive, 220v, 3ph. 4 speed power feed to 6 position turret. 180 rpm back gear to 1800 max.
Hole through spindle 1 9/32, push bar for collet operator . Lever operated cross slide, hand wheel feed to carriage.
This is a very nice (old) machine!! |
|
Ad # 7622 | Ram Type & Saddle Type Turret Lathes |
|
Acme |
# 1 |
Fair |
sold |
Photo /
More Info. |
Acme # 1 Turrel Lathe: 12 in 3 jaw chuck |
|
Ad # 7618 | Ram Type & Saddle Type Turret Lathes |
|
Gisholt |
# 4 |
Fair |
Sold |
Photo /
More Info. |
Gishold # 4, 2-1/2" Spindle Bore Turret Lathe: Spindle Bore: 2-1/2" diameter
Comes with a barfeeder |
|
Ad # 7619 | Ram Type & Saddle Type Turret Lathes |
|
Libby |
4-R Chucker |
|
sold |
Photo /
More Info. |
Libby 4-R Chucker Lathe: A great general purpose or spares machine
12 inch 3 jaw chuck
swing over cross slide:6"over cross slide |
|
Ad # 2716 | Ram Type & Saddle Type Turret Lathes |
|
Bardons & Oliver |
#2 |
Fair |
sold |
Photo /
More Info. |
Bardons & Oliver Manual Turret Lathe: 1" spindle bore
12" centers
4 speed
no tooling included
6 position turret
Belt drive-flat
on a skid |
|
Ad # 13927 | Ram Type & Saddle Type Turret Lathes |
1960's ? |
Warner & Swasey |
No.3 |
Good |
sold |
Photo /
More Info. |
15" Swing over bed: Warner & Swasey Turret Lathe
Model: No. 3
Swing over ways:15
Swing over cross slide:7
Cross slide travel:8
Carriage travel:17
Carriage feeds:.0025-.026 TPR
Max distance turret face to spindle nose:26
(approx.)
Turret feeds:.003-.030 TPR
Max turret stroke:10
Spindle speeds (12):67-1480 RPM
Spindle hole:1-3/4
Spindle nose:A-6
Bar feed capacity:1-1/2
Motor:7.5 HP, 220 volt, 3 phase
Includes 3 Jaw Chuck, Collet Closer with collet
pad set, 4 way Tool Post |
|
Ad # 4691 | Ram Type & Saddle Type Turret Lathes |
1954 |
MONARCH |
10" EE |
Very Good |
sold |
Photo /
More Info. |
10" EE MONARCH TURRET LATHE: 10" EE MONARCH TURRET LATHE
ACTUAL SWING 12"
DATE BUILT 1954
6 POS TURRET COMPOUND FEEDS .002/.012
CUT OFF AND CROSS SLIDE RPM 1/4000
VARIABLE SPEED
SPRING COLLET
SYSTEM W/COLLETS |
|
Ad # 143 | Ram Type & Saddle Type Turret Lathes |
1955 |
Gisholt |
Turret Lathe 13W-9136 |
Fair |
sold |
Photo /
More Info. |
Large 25" Turret Lathe w/ Tooling: Large 6 station Turret Lathe
Swing 25" over ways
18" chuck-3-jaw w/T-slot
Length 5'from chuck to turret
Misc Tooling
4" spindle bore |
|
Ad # 13803 | Ram Type & Saddle Type Turret Lathes |
1960's |
Warner & Swasey |
M-2250 # 5 |
Good |
sold |
Photo /
More Info. |
20" Turret with tooling: Warner & Swasey Turret Lathe
Model: M-2250 # 5 Lot 34
Electrical: 460/3 phase
Tooling and cabinet included
Swing Over Ways: 20"
Swing Over Carriage: 10-1/4"
Swing in Gap: 31-1/2"
Gap Bed Will Slide Back: Approx. 20"
Max. Distance Chuck to Turret, Bed Closed: Approx. 28"
Max. Distance Chuck to Turret, Bed Open: Approx. 47"
Spindle Speeds: 25 to 1556 RPM
Spindle Hole: 2-7/8"
Spindle Nose: A1-8
(6) Carriage Feeds: .004 to .045 TPR
(6) Cross Slide Feeds: .003 to .027 TPR
(6) Turret Feeds: .005 to .048 TPR
Turret Stroke: 12"
20/10 HP Motor
|
|
Ad # 9216 | Ram Type & Saddle Type Turret Lathes |
|
Warner |
1SC |
Fair |
sold |
Photo /
More Info. |
Turret Lathe 12 in chuck: 84-2000 rpm
5330 control
12 station turret
all books included
2-3/8 Dia bar feeder capacity-needs work
lots and lots of tooling included
it runs
|
|
Ad # 14540 | Ram Type & Saddle Type Turret Lathes |
? |
G & L |
# 5-3 |
Good |
sold |
Photo /
More Info. |
16" x 24": G & L Universal turret lathe #5-3
16" swing over ways
3.5" spindle bore
24" center dist
rpm: 30-1500
threading with right acc...not included
6 position turret
|
|
Ad # 14540 | Ram Type & Saddle Type Turret Lathes |
? |
G & L |
# 5-3 |
Good |
sold |
Photo /
More Info. |
16" x 24": G & L Universal turret lathe #5-3
16" swing over ways
3.5" spindle bore
24" center dist
rpm: 30-1500
threading with right acc...not included
6 position turret
|
|
Ad # 1755 | Ram Type & Saddle Type Turret Lathes |
|
Gisholt |
# 3 |
Good |
SOLD |
Photo /
More Info. |
Gisholt # 3 Turret Lathe: Swing: 20"
DBC: 26"
Spindle Bore: 3 1/4"
6 Station Turret
10" 3-Jaw Chuck
|
|
Ad # 9197 | Ram Type & Saddle Type Turret Lathes |
|
Warner & Swasey |
#3 |
Very Good |
sold |
Photo /
More Info. |
67-1480RPM: Barfeed, includes some collets up to 1&1/2", Operation and maint. manual. |
|
Ad # 7157 | Ram Type & Saddle Type Turret Lathes |
|
Jones & Lamson |
# 3 (1-1/2in) |
Good |
sold |
Photo /
More Info. |
1-1/2" Jones & Lamson # 3 Universal Turret Lathe : Spindle Bore: 1-1/2" diameter
Includes:
10" 3-Jaw Chuck
Collet Chuck with lots of Collets
2 x Tool Posts
|
|
Ad # 13125 | Ram Type & Saddle Type Turret Lathes |
|
Jones & Lamson |
No. 9 B |
Good |
sold |
Photo /
More Info. |
: 15" 3 Jaw Chuck ,
swing over ways 12 , over table 9" ,distance
between centers 50" to 60" , chip pan , 6
position
turret , 4 position tool post , machine was
running when it was put in storage . make offer |
|
Ad # 4398 | Ram Type & Saddle Type Turret Lathes |
1944 |
Monarch |
12"CKK |
Fair |
SOLD |
Photo /
More Info. |
Quality built manual lathe14.5" x 30": 14.5" swing over bed
30" between centers
Inch threading
QC toolpost W/ misc holders
1.5" spindle bore
8" 3 Jaw chuck
taper attachment
13-560 RPM |
|
Ad # 8148 | Ram Type & Saddle Type Turret Lathes |
|
Warner & Swasey |
4A |
Good |
SOLD |
Photo /
More Info. |
28" swing x 50" centers: 28" swing over bed
24" Chuck
50" center dist.
4-212 RPM |
|
Ad # 11863 | Ram Type & Saddle Type Turret Lathes |
1992 |
Enco |
112-8100 |
Needs Work |
sold |
Photo /
More Info. |
: Enco # 112-8100 turret lathe
6-POSITION TURRET
COOLANT
COLLET CLOSER
1850 rpm spindle. 6 position turret. 27 collets. |
|
Ad # 9146 | Ram Type & Saddle Type Turret Lathes |
? |
Warner and Swasey |
#3 w/barfeed |
Good |
sold |
Photo /
More Info. |
# 3 w/ bar feed: With Barfeeder, oversized spindle bore (approximate 2")and chuck, uses #4 c... |
|
Ad # 11812 | Ram Type & Saddle Type Turret Lathes |
? |
Warner & Swasey |
1A - M3400 |
Good |
sold |
Photo /
More Info. |
W & S # 1A # M3400 turret lathe: Warner $ Sawsey # 1A -m3400 lot 6 turret lathe
30 HP
16" swing over bed
12" 3 jaw chuck
36" centers
great condition
rigger required to load add $ 800.00 |
|